Search
Search

Download für EAP330 V2

Bitte wählen Sie Ihre Hardware-Version aus.:

V2

>Wie finde ich die Hardware Version auf einem TP-Link Gerät?

WICHTIG: Die Verfügbarkeit von Modellnummer und Hardwareversion hängt von Ihrer Region ab. Bitte schauen Sie auf Ihrer lokalen TP-Link-Webpräsenz nach, um die Produktverfügbarkeit zu überprüfen.
Dokument

EAP330

Setup Video

  • How to manage TP-Link EAPs centrally via the Software Controller

    This video demonstrates how to manage TP-Link EAPs centrally via the Software Controller. The setup consists of three steps:
    • Install the Software
    • Configure Discovery Utility (If your EAPs and the Controller Host are on different subnets)
    • Configure Software Controller

    THIS VIDEO APPLIES TO:
    • All TP-Link EAP models (except EAP120 and EAP220)
    • Omada Software Controller
    • Mass EAPs (usually more than three)

    Weitere Informationen

  • How to set up a TP Link EAP via your mobile phone

    This video demonstrates how to set up a TP-Link EAP via your mobile phone. The setup consists of four steps:
    • Connect the EAP to the network
    • Download the Omada APP
    • Connect to the EAP's wireless network
    • Set up the EAP using the Omada APP

    THIS VIDEO APPLIES TO:
    • All TP-Link EAP models. (except EAP120 and EAP220)
    • A small number (1-3) of EAPs.

    Weitere Informationen

  • How to setup the OC200 via a web browser

    This video will demonstrate how to set up the OC200 via a web browser. The setup consists of six steps:
    • Connect the OC200 to your local network.
    • Get ready for setup.
    • Create a TP-Link ID.
    • Log into your TP-Link ID.
    • Add the OC200 to your TP-Link ID.
    • Follow the wizard to set up the OC200.

    THIS VIDEO APPLIES TO:
    • All TP-Link EAP models (except EAP120 and EAP220)
    • Omada Cloud Controller OC200
    • Mass EAPs (usually more than three)

    Weitere Informationen

  • How to setup the OC200 via your mobile phone

    This video will demonstrate how to set up the OC200 via your mobile phone. You need to use the Omada APP to complete the setup. The setup consists of six steps:
    • Connect the OC200 to your local network.
    • Get ready for setup.
    • Create a TP-Link ID.
    • Log into your TP-Link ID.
    • Add the OC200 to your TP-Link ID.
    • Follow the wizard to set up the OC200.
    THIS VIDEO APPLIES TO:
    • All TP-Link EAP models (except EAP120 and EAP220)
    • Omada Cloud Controller OC200
    • Mass EAPs (usually more than three)

    Weitere Informationen

  • How to manage TP-Link EAPs centrally from a remote place via a web browser

    You can manage TP-Link EAPs at any time from anywhere with the Cloud Access function of our Omada Controller Software. This video introduces both the application scenario and concrete steps you can follow. Don't hesitate to give it a try.
    THIS VIDEO APPLIES TO:
    • All TP-Link EAP models (except EAP120 and EAP220)
    • Omada Controller Software (version 3.0.2 or above)
    • Mass EAPs (usually more than three)

    Weitere Informationen

  • How to Set up a TP-Link EAP via Web browser

    This video will demonstrate how to set up a TP-Link EAP via a web browser. The setup consists of three steps:
    1. Connect the EAP to the network
    2. Log into the EAP (via a wired/wireless connection)
    3. Change the default SSID
    This video is suitable for users with a small number (1-3) of EAPs .

    Weitere Informationen

Feature Filter: Alles Configuration GuideQ&A of functional explanation or specification parametersUser Application RequirementTroubleshooting

Häufig gestellte Fragen

Firmware

Ein Firmware-Update kann für Sie neue Funktionen und Fehlerbehebungen und Performanceverbesserungen bereithalten.

Zum Firmware-Upgrade

HINWEIS: Um Fehler bei der Aktualisierung zu vermeiden, lesen Sie sich bitte folgende Hinweise durch, bevor Sie das Upgrade tätigen.

  • Bitte stellen Sie sicher, dass die Firmwareversion, die Sie zu installieren beabsichtigen, für Ihre Hardwareversion freigegeben ist. Eine nicht passende Firmware kann Ihr Gerät beschädigen und Ihren Anspruch auf Garantie erlöschen lassen. Normalerweise gilt V1.x=V1.
    Es wird NICHT empfohlen, eine nicht für Ihren Standort vorgesehene Firmware zu installieren. Klicken Sie hier, um Ihren Standort zu wählen und dann eine geeignete Firmware herunterzuladen (z.B. bestehen Unterschiede zwischen der EU- und der US-Version)
  • Trennen Sie während des Upgradevorgangs KEINESFALLS die Spannungsversorgung.
  • Aktualisieren Sie die Firmware NICHT über eine WLAN-Verbindung, außer Ihr Gerät verfügt über keinen Kabelanschluss.
  • Es wird empfohlen, während des Upgrades keine Internetanwendungen auszuführen bzw. einfach vor dem Upgrade die Internetverbindung des Gerätes zu trennen.
  • Verwenden Sie Entpack-Software wie WinZIP oder WinRAR, um die heruntergeladene Datei vor dem Upgrade zu entpacken.
EAP330(EU)_V2_1.4.0 Build 20180925
Datum der Veröffentlichung: 2018-10-16 Sprache: Englisch Dateigröße: 7.73 MB

Recommended Controller Software Version:  Omada Controller v 2.6.x or above

 

New Features/Improvements:

1. Support Omada APP management method.

2. Support HTTPS redirection of portal authentication page.

3. Support URL Free Authentication Policy

4. Support rate limit function for a single client. (If you have set SSID, Client, Voucher rate limit together, the minimum limit value will take effect.)

5. Omada Controller increased the synchronization update process when the IP address of EAP is changed.

6. EAP will report Client RSSI information to Omada Controller.

7. The hardware version will be displayed as 1.0/2.0 in the management page.

 

Bug Fixed:

1. Fixed the bug that EAP will reboot automatically when Airtime Fairness function is enabled.

2. Fixed the bug that wireless clients may be displayed with abnormal IP address in Omada Controller.

3. Fixed the bug that HTTPS redirection of Portal authentication page will be inoperative when the IP address of Omada EAP and wireless clients belong to different subnet.

4. Optimized the problem that EAP will be disconnected from Omada Controller.

 

Notes:

1. For EAP330 (EU)_V2 only.

2. Your device's configuration won't be lost after upgrading.
EAP330(EU)_V2_170930
Datum der Veröffentlichung: 2017-09-30 Sprache: Englisch Dateigröße: 7.63 MB

Recommended Controller Software Version: Omada Controller v 2.5.x

New Features/Improvements:

1. Support new SMS, Facebook and other authentication methods of Omada Controller 2.5.x.

2. Voucher supports speed limit of clients.

Bug Fixed:

1. Web management pages have syntax errors or inconsistent formats

2. EAP330 cannot be managed across different subnets when management VLAN is enabled.

Notes:

1. For EAP330 (EU) v2

2. Your device's configuration won't be lost after upgrading.
EAP330(EU)_V2_170711
Datum der Veröffentlichung: 2017-07-11 Sprache: Englisch Dateigröße: 7.60 MB

Recommended Controller Software Version: Omada Controller v 2.4.x

New Features/Improvements:

Enhance the capability of anti-interference.

Bug Fixed:

Fix the bug that the Security Mode will turn to None if using a space character in the WPA/WPA2-PSK password.

Notes:

1. For EAP330(EU) v2.

2. Your device's configuration won't be lost after upgrading.

Verwendung von Third-Party-Firmware auf TP-Link-Produkten

Die Original-Firmware einiger TP-Link-Produkte kann durch Third-Party-Firmware wie DD-WRT ersetzt werden. TP-Link ist weder verpflichtet, für derart modifizierte Geräte Support oder Garantie zu leisten noch für deren Stabilität oder Leistungsfähigkeit zu garantieren. TP-Link wird keinerlei durch Third-Party-Firmware verursachte Schäden ersetzen.

Open-Source-Code für Entwickler (GPL)

Die folgenden Informationen sind für Entwickler gedacht und für die meisten Nutzer von TP-Link-Produkten uninteressant.

TP-Link-Produkte enthalten teilweise von Dritten entwickelten Softwarecode, darunter Code, der unter die GNU General Public Licence (“GPL“), Version 1/Version 2/Version 3 oder die GNU Lesser General Public License ("LGPL") gestellt ist. Diese Software können Sie unter Beachtung der damit verbundenen Bedingungen benutzen.

Sie können die GPL-Lizenzbedingungen hier ansehen, herunterladen und drucken. Sie bekommen die GPL-Sourcecodes der in TP-Link-Produkten verwendeten Software per Direktdownload sowie weitere Information, unter Anderem eine Liste der TP-Link-Software, welche GPL-Softwarecode enthält, unter GPL Code Center.

Diese Programme werden OHNE JEGLICHE GEWÄHRLEISTUNG weitergegeben. Auch die HERSTELLERGARANTIE und die GEWÄHRLEISTUNG gelten für diese nicht. Für Details sei auf die GNU General Public License verwiesen.

Controller Software

Der EAP-Controller ist dazu da, mehrere EAPs gemeinsam und zentral zu steuern.

Datum der Veröffentlichung: 2020-04-20 Sprache: Englisch Dateigröße: 120.54MB
Betriebssystem: Windows 7/8/10/Server

New Feature/Enhancement:

1. Added the feature that the system logs can be exported.

2. Changed the priority that non-administrator role cannot change the history data retention settings.

3. Optimized the UI of Statistics in Omada Controller.

 

Bug Fixed:

1. Fixed the bug that the External Web Portal cannot authenticate successfully if the SSID of this portal has special characters.

2. Fixed the bug that the Cloud Access cannot be displayed normally in the low version of Firefox.

3. Fixed the bug that Omada Controller allow any user to read the files of controller.

4. Fixed the bug that controller will report an error when Top Usage data is empty.

 

Notes:

1. To use Omada Controller 3.2.X new features, you need to upgrade your EAP's firmware to the corresponding version.

2. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

3. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.X or earlier version.
Datum der Veröffentlichung: 2020-04-20 Sprache: Englisch Dateigröße: 124.46MB
Betriebssystem: Windows 7/8/10/Server

New Feature/Enhancement:

1. Added the feature that the system logs can be exported.

2. Changed the priority that non-administrator role cannot change the history data retention settings.

3. Optimized the UI of Statistics in Omada Controller.

 

Bug Fixed:

1. Fixed the bug that the External Web Portal cannot authenticate successfully if the SSID of this portal has special characters.

2. Fixed the bug that the Cloud Access cannot be displayed normally in the low version of Firefox.

3. Fixed the bug that Omada Controller allow any user to read the files of controller.

4. Fixed the bug that controller will report an error when Top Usage data is empty.

 

Notes:

1. To use Omada Controller 3.2.X new features, you need to upgrade your EAP's firmware to the corresponding version.

2. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

3. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.X or earlier version.
Datum der Veröffentlichung: 2020-04-20 Sprache: Englisch Dateigröße: 99.4MB
Betriebssystem: Ubuntu 14.04/16.04/17.04/18.04/Debian 9.8

Bug Fixed:

1. Fixed the bug that Omada Controller allow any user to read the files of controller.

2. Fixed the bug that controller will report an error when Top Usage data is empty. 

 

Notes:

1. To use new features on Omada Controller 3.2.X, you need to upgrade your EAP's firmware to the corresponding version.

2. The Omada Controller program needs to use the system's netstat command. If the Linux system does not have net-tools installed (which contain the netstat command), the program may not be able to run normally.

3. Support 64-bit Linux operating system including Ubuntu 14.04/16.04/17.04/18.04/Debian 9.8

4. Built-in JRE 1.8 Java environment.

5. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

6. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.8.
Datum der Veröffentlichung: 2020-04-20 Sprache: Englisch Dateigröße: 125.64MB
Betriebssystem: Ubuntu 14.04/16.04/17.04/18.04, CentOS 6.x/7.x and Fedora 20 or above, Debian 9.8.

Bug Fixed:

1. Fixed the bug that Omada Controller allow any user to read the files of controller.

2. Fixed the bug that controller will report an error when Top Usage data is empty. 

 

Notes:

1. To use new features on Omada Controller 3.2.x, you need to upgrade your EAP's firmware to the corresponding version.

2. The Omada Controller program needs to use the system's netstat command. If the Linux system does not have net-tools installed (which contain the netstat command), the program may not be able to run normally.

3. Support 64-bit Linux operating system including Ubuntu 14.04/16.04/17.04/18.04, CentOS 6.x/7.x and Fedora 20 or above, Debian 9.8.

4. Built-in JRE 1.8 Java environment.

5. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

6. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.8.

7. When upgrading from Controller 2.5.3 Linux to this version via install.sh, you need to uninstall old version of Controller first.
Datum der Veröffentlichung: 2020-04-09 Sprache: Englisch Dateigröße: 99.39MB
Betriebssystem: Ubuntu 14.04/16.04/17.04/18.04/Debian 9.8

New Feature/Enhancement:

1. Add the feature that the system logs can be exported.

2. Change the priority that non-administrator role cannot change the history data retention settings.

3. Optimize the UI of Statistics in Omada Controller.

 

Bug Fixed:

1. Fix the bug that the External Web Portal cannot authenticate successfully if the SSID of this portal has special characters.

2. Fix the bug that the Cloud Access cannot be displayed normally in the low version of Firefox.

 

Notes:

1. To use new features on Omada Controller 3.2.X, you need to upgrade your EAP's firmware to the corresponding version.

2. The Omada Controller program needs to use the system's netstat command. If the Linux system does not have net-tools installed (which contain the netstat command), the program may not be able to run normally.

3. Support 64-bit Linux operating system including Ubuntu 14.04/16.04/17.04/18.04/Debian 9.8

4. Built-in JRE 1.8 Java environment.

5. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

6. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.8.
Datum der Veröffentlichung: 2020-04-09 Sprache: Englisch Dateigröße: 123.36MB
Betriebssystem: Ubuntu 14.04/16.04/17.04/18.04, CentOS 6.x/7.x and Fedora 20 or above, Debian 9.8.

New Feature/Enhancement:

1. Add the feature that the system logs can be exported.

2. Change the priority that non-administrator role cannot change the history data retention settings.

3. Optimize the UI of Statistics in Omada Controller.

 

Bug Fixed:

1. Fix the bug that the External Web Portal cannot authenticate successfully if the SSID of this portal has special characters.

2. Fix the bug that the Cloud Access cannot be displayed normally in the low version of Firefox.

 

 

Notes:

1. To use new features on Omada Controller 3.2.x, you need to upgrade your EAP's firmware to the corresponding version.

2. The Omada Controller program needs to use the system's netstat command. If the Linux system does not have net-tools installed (which contain the netstat command), the program may not be able to run normally.

3. Support 64-bit Linux operating system including Ubuntu 14.04/16.04/17.04/18.04, CentOS 6.x/7.x and Fedora 20 or above, Debian 9.8.

4. Built-in JRE 1.8 Java environment.

5. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

6. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.8.

7. When upgrading from Controller 2.5.3 Linux to this version via install.sh, you need to uninstall old version of Controller first.
Datum der Veröffentlichung: 2020-01-21 Sprache: Englisch Dateigröße: 120.53MB
Betriebssystem: Windows 7/8/10/Server

New Feature/Enhancement:

1. Expand the number of Omada Controller’s User Account to 500.  

2. Optimize the External Portal Server to support URL with parameters.

 

Notes:

1. To use Omada Controller 3.2.X new features, you need to upgrade your EAP's firmware to the corresponding version.

2. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

3. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.X or earlier version.

 
Datum der Veröffentlichung: 2020-01-21 Sprache: Englisch Dateigröße: 124.45MB
Betriebssystem: Windows 7/8/10/Server

New Feature/Enhancement:

1. Expand the number of Omada Controller’s User Account to 500.  

2. Optimize the External Portal Server to support URL with parameters.

 

Notes:

1. To use Omada Controller 3.2.X new features, you need to upgrade your EAP's firmware to the corresponding version.

2. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

3. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.X or earlier version.
Datum der Veröffentlichung: 2020-01-16 Sprache: Englisch Dateigröße: 123.35MB
Betriebssystem: Ubuntu 14.04/16.04/17.04/18.04, CentOS 6.x/7.x and Fedora 20 or above, Debian 9.8.

New Feature/Enhancement:

1. Change the mechanism that when adopting an EAP, the Controller will retain the IP configuration of EAP in Standalone mode.

2. Change the mechanism that multiple Omada Controllers can run on the same subnet.

3. Add the button of “Start Omada Controller after installation” and check it by default.

4. Extend the Max Associated Clients in Load Balance to 255.

5. Optimize the UI of Channel Utilization.

6. Optimize the authentication page of portal.

7. Optimize the UI of the portal that you cannot click Apply when you are uploading a photo.

8. Optimize the External Portal Server to support URL with parameters.

 

Bug Fixed:

1. Fixed the bug that the page of MAC filter may not display all groups when there are more than 5 groups.

2. Fixed the bug that after deleting a site, the Voucher code and Local user of this site still exist.

3. Fixed the bug that the site configuration will fail to restore when the imported site contains same Voucher code as the current Controller.

4. Fixed the bug that when mesh AP is powered off during upgrade, Controller may fail to upgrade other APs, with a prompt message “Other APs are upgrading”.

 

Notes:

1. To use new features on Omada Controller 3.2.x, you need to upgrade your EAP's firmware to the corresponding version.

2. The Omada Controller program needs to use the system's netstat command. If the Linux system does not have net-tools installed (which contain the netstat command), the program may not be able to run normally.

3. Support 64-bit Linux operating system including Ubuntu 14.04/16.04/17.04/18.04, CentOS 6.x/7.x and Fedora 20 or above, Debian 9.8.

4. Built-in JRE 1.8 Java environment.

5. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

6. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.8.

7. When upgrading from Controller 2.5.3 Linux to this version via install.sh, you need to uninstall old version of Controller first.

 
Datum der Veröffentlichung: 2020-01-16 Sprache: Englisch Dateigröße: 99.4MB
Betriebssystem: Ubuntu 14.04/16.04/17.04/18.04/Debian 9.8

New Feature/Enhancement:

1. Change the mechanism that when adopting an EAP, the Controller will retain the IP configuration of EAP in Standalone mode.

2. Change the mechanism that multiple Omada Controllers can run on the same subnet.

3. Add the button of “Start Omada Controller after installation” and check it by default.

4. Extend the Max Associated Clients in Load Balance to 255.

5. Optimize the UI of Channel Utilization.

6. Optimize the authentication page of portal.

7. Optimize the UI of the portal that you cannot click Apply when you are uploading a photo.

8. Optimize the External Portal Server to support URL with parameters.

 

Bug Fixed:

1. Fixed the bug that the page of MAC filter may not display all groups when there are more than 5 groups.

2. Fixed the bug that after deleting a site, the Voucher code and Local user of this site still exist.

3. Fixed the bug that the site configuration will fail to restore when the imported site contains same Voucher code as the current Controller.

4. Fixed the bug that when mesh AP is powered off during upgrade, Controller may fail to upgrade other APs, with a prompt message “Other APs are upgrading”.

 

Notes:

1. To use new features on Omada Controller 3.2.X, you need to upgrade your EAP's firmware to the corresponding version.

2. The Omada Controller program needs to use the system's netstat command. If the Linux system does not have net-tools installed (which contain the netstat command), the program may not be able to run normally.

3. Support 64-bit Linux operating system including Ubuntu 14.04/16.04/17.04/18.04/Debian 9.8

4. Built-in JRE 1.8 Java environment.

5. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

6. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.8.
Datum der Veröffentlichung: 2020-01-09 Sprache: Englisch Dateigröße: 120.53MB
Betriebssystem: Windows 7/8/10/Server

New Feature/Enhancement:

1. Change the mechanism that when adopting an EAP, the Controller will retain the IP configuration of EAP in Standalone mode.

2. Change the mechanism that multiple Omada Controllers can run on the same subnet.

3. Add the button of “Start Omada Controller after installation” and check it by default.

4. Extend the Max Associated Clients in Load Balance to 255.

5. Optimize the UI of Channel Utilization.

6. Optimize the authentication page of portal.

7. Optimize the UI of the portal that you cannot click Apply when you are uploading a photo.

 

Bug Fixed:

1. Fixed the bug that the page of MAC filter may not display all groups when there are more than 5 groups.

2. Fixed the bug that after deleting a site, the Voucher code and Local user of this site still exist.

3. Fixed the bug that the site configuration will fail to restore when the imported site contains same Voucher code as the current Controller.

4. Fixed the bug that when mesh AP is powered off during upgrade, Controller may fail to upgrade other APs, with a prompt message “Other APs are upgrading”.

 

Notes:

1. To use Omada Controller 3.2.X new features, you need to upgrade your EAP's firmware to the corresponding version.

2. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

3. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.X or earlier version.
Datum der Veröffentlichung: 2020-01-09 Sprache: Englisch Dateigröße: 124.44MB
Betriebssystem: Windows 7/8/10/Server

New Feature/Enhancement:

1. Change the mechanism that when adopting an EAP, the Controller will retain the IP configuration of EAP in Standalone mode.

2. Change the mechanism that multiple Omada Controllers can run on the same subnet.

3. Add the button of “Start Omada Controller after installation” and check it by default.

4. Extend the Max Associated Clients in Load Balance to 255.

5. Optimize the UI of Channel Utilization.

6. Optimize the authentication page of portal.

7. Optimize the UI of the portal that you cannot click Apply when you are uploading a photo.

 

Bug Fixed:

1. Fixed the bug that the page of MAC filter may not display all groups when there are more than 5 groups.

2. Fixed the bug that after deleting a site, the Voucher code and Local user of this site still exist.

3. Fixed the bug that the site configuration will fail to restore when the imported site contains same Voucher code as the current Controller.

4. Fixed the bug that when mesh AP is powered off during upgrade, Controller may fail to upgrade other APs, with a prompt message “Other APs are upgrading”.

 

Notes:

1. To use Omada Controller 3.2.X new features, you need to upgrade your EAP's firmware to the corresponding version.

2. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

3. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.X or earlier version.
Datum der Veröffentlichung: 2019-11-08 Sprache: Englisch Dateigröße: 99.4MB
Betriebssystem: Ubuntu 14.04/16.04/17.04/18.04/Debian 9.8

New Feature/Enhancement:

1. Add “Select Page” feature on voucher management page.

2. Change default status of “Terms of Service” on default portal page to uncheck.

3. Optimize the “Free Authentication Policy” to support URL with suffixes.

4. Change the default status of new added “Free Authentication Policy” to enable.

 

Bug Fixed:

1. Fixed the bug that when clients disconnect from the Facebook portal, the connection time and traffic usage of these clients may be zero in the log.

2. Fixed the bug that AP may disconnect from Omada Controller when it is upgrading the firmware.

3. Fixed the bug that in some cases, the channel configuration of 2.4G frequency may show up in 5G by mistake.

4. Fixed the bug that the configuration of SSID will not be issued correctly when changing the WLAN Group on the provisioning status.

 

Notes:

1. To use new features on Omada Controller 3.2.X, you need to upgrade your EAP's firmware to the corresponding version.

2. The Omada Controller program needs to use the system's netstat command. If the Linux system does not have net-tools installed (which contain the netstat command), the program may not be able to run normally.

3. Support 64-bit Linux operating system including Ubuntu 14.04/16.04/17.04/18.04/Debian 9.8

4. Built-in JRE 1.8 Java environment.

5. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

6. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.8.
Datum der Veröffentlichung: 2019-11-08 Sprache: Englisch Dateigröße: 123.35MB
Betriebssystem: Ubuntu 14.04/16.04/17.04/18.04, CentOS 6.x/7.x and Fedora 20 or above, Debian 9.8.

New Feature/Enhancement:

1. Add “Select Page” feature on the management page of vouchers.

2. Change the default status of “Terms of Service” to uncheck.

3. Optimize the “Free Authentication Policy” to support URL with suffixes.

4. Change the default status of new added “Free Authentication Policy” to enable.

 

Bug Fixed:

1. Fixed the bug that when clients disconnect from the Facebook portal, the connection time and traffic usage of these clients may be zero in the log.

2. Fixed the bug that AP may disconnect from Omada Controller when it is upgrading the firmware.

3. Fixed the bug that in some cases, the channel configuration of 2.4G frequency may show up in 5G by mistake.

4. Fixed the bug that the configuration of SSID will not be issued correctly when changing the WLAN Group on the provisioning status.

 

 

Notes:

1. To use new features on Omada Controller 3.2.x, you need to upgrade your EAP's firmware to the corresponding version.

2. The Omada Controller program needs to use the system's netstat command. If the Linux system does not have net-tools installed (which contain the netstat command), the program may not be able to run normally.

3. Support 64-bit Linux operating system including Ubuntu 14.04/16.04/17.04/18.04, CentOS 6.x/7.x and Fedora 20 or above, Debian 9.8.

4. Built-in JRE 1.8 Java environment.

5. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

6. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.8.

7. When upgrading from Controller 2.5.3 Linux to this version via install.sh, you need to uninstall old version of Controller first.
Datum der Veröffentlichung: 2019-11-08 Sprache: Englisch Dateigröße: 120.52MB
Betriebssystem: Windows 7/8/10/Server

New Feature/Enhancement:

1. Add “Select Page” feature on the voucher management page.

2. Change the default status of “Terms of Service” on default portal page to uncheck.

3. Optimize the “Free Authentication Policy” to support URL with suffixes.

4. Change the default status of new added “Free Authentication Policy” to enable.

 

Bug Fixed:

1. Fixed the bug that when clients disconnect from the Facebook portal, the connection time and traffic usage of these clients may be zero in the log.

2. Fixed the bug that AP may disconnect from Omada Controller when it is upgrading the firmware.

3. Fixed the bug that in some cases, the channel configuration of 2.4G frequency may show up in 5G by mistake.

4. Fixed the bug that the configuration of SSID will not be issued correctly when changing the WLAN Group on the provisioning status.

 

Notes:

1. To use Omada Controller 3.2.x new features, you need to upgrade your EAP's firmware to the corresponding version.

2. Once upgraded to this version of Omada Controller, you will NOT be able to downgrade to an earlier version.

3. Portal configuration will be lost after upgrading to Omada Controller 3.2.X from 2.4.X or earlier version.

4. You are recommended to create a backup before upgrading, or you will not be permitted to install this version of Omada Controller.
Datum der Veröffentlichung: 2019-11-08 Sprache: Englisch Dateigröße: 124.43MB
Betriebssystem: Windows 7/8/10/Server

New Feature/Enhancement:

1. Add “Select Page” feature on the voucher management page.

2. Change the default status of “Terms of Service” on default portal page to uncheck.

3. Optimize the “Free Authentication Policy” to support URL with suffixes.

4. Change the default status of new added “Free Authentication Policy” to enable.

 

Bug Fixed:

1. Fixed the bug that when clients disconnect from the Facebook portal, the connection time and traffic usage of these clients may be zero in the log.

2. Fixed the bug that AP may disconnect from Omada Controller when it is upgrading the firmware.

3. Fixed the bug that in some cases, the channel configuration of 2.4G frequency may show up in 5G by mistake.

4. Fixed the bug that the configuration of SSID will not be issued correctly when changing the WLAN Group on the provisioning status.

 

Notes:

1. To use Omada Controller 3.2.x new features, you need to upgrade your EAP's firmware to the corresponding version.

2. Once upgraded to this version of Omada Controller, you will NOT be able to downgrade to an earlier version.

3. Portal configuration will be lost after upgrading to Omada Controller 3.2.X from 2.4.X or earlier version.

4. You are recommended to create a backup before upgrading, or you will not be permitted to install this version of Omada Controller.
Datum der Veröffentlichung: 2019-07-26 Sprache: Englisch Dateigröße: 99.23MB
Betriebssystem: Ubuntu 14.04/16.04/17.04/18.04/Debian 9.8

New Feature/Enhancement:

1. Optimize the performance of Controller to manage up to 1500 EAPs.

2. Optimize the interactive process between EAP and Controller to decrease the processing time.

3. Limit the entry number of client/client history/guest to 1.2 million/1.2 million /6 million.

4. Optimize display page of map and log when there are a lot of entries.

 

Bug Fixed:

1. Fixed the bug that CPU and memory may be highly used when Fast Roaming is enabled.

2. Fixed the bug that Omada Controller reports timeout error when adopting multiple EAPs simultaneously.

3. Fixed the bug that Controller will print all Voucher codes even only some of the codes are selected.

 

Notes:

1. To use new features on Omada Controller 3.2.X, you need to upgrade your EAP's firmware to the corresponding version.

2. The Omada Controller program needs to use the system's netstat command. If the Linux system does not have net-tools installed (which contain the netstat command), the program may not be able to run normally.

3. Support 64-bit Linux operating system including Ubuntu 14.04/16.04/17.04/18.04/Debian 9.8

4. Built-in JRE 1.8 Java environment.

5. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

6. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.8.

 
Datum der Veröffentlichung: 2019-07-26 Sprache: Englisch Dateigröße: 123.15MB
Betriebssystem: Ubuntu 14.04/16.04/17.04/18.04, CentOS 6.x/7.x and Fedora 20 or above, Debian 9.8.

New Feature/Enhancement:

1. Optimize the performance of Controller to manage up to 1500 EAPs.

2. Optimize the interactive process between EAP and Controller to decrease the processing time.

3. Limit the entry number of client/client history/guest to 1.2 million/1.2 million /6 million.

4. Optimize display page of map and log when there are a lot of entries.

 

Bug Fixed:

1. Fixed the bug that CPU and memory may be highly used when Fast Roaming is enabled.

2. Fixed the bug that Omada Controller reports timeout error when adopting multiple EAPs simultaneously.

3. Fixed the bug that Controller will print all Voucher codes even only some of the codes are selected.

 

Notes:

1. To use new features on Omada Controller 3.2.x, you need to upgrade your EAP's firmware to the corresponding version.

2. The Omada Controller program needs to use the system's netstat command. If the Linux system does not have net-tools installed (which contain the netstat command), the program may not be able to run normally.

3. Support 64-bit Linux operating system including Ubuntu 14.04/16.04/17.04/18.04, CentOS 6.x/7.x and Fedora 20 or above, Debian 9.8.

4. Built-in JRE 1.8 Java environment.

5. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

6. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.8.

7. When upgrading from Controller 2.5.3 Linux to this version via install.sh, you need to uninstall old version of Controller first.
Datum der Veröffentlichung: 2019-07-04 Sprache: Englisch Dateigröße: 120.29MB
Betriebssystem: Windows 7/8/10/Server

New Feature/Enhancement:

1. Optimize the performance of Controller to manage up to 1500 EAPs.

2. Optimize the interactive process between EAP and Controller to decrease the process time.

3. Limit the entry number of client/client history/guest to 1.2 million/1.2 million /6 million.

4. Optimize display page of map and log when there are a lot of entries.

 

Bug Fixed:

1. Fixed the bug that CPU and memory may be highly used when Fast Roaming is enabled.

2. Fixed the bug that Omada Controller reports timeout error when adopting multiple EAPs simultaneously.

3. Fixed the bug that Controller will print all Voucher codes even only some of the codes are selected.

 

Notes:

1. To use Omada Controller 3.2.x new features, you need to upgrade your EAP's firmware to the corresponding version.

2. Once upgraded to this version of Omada Controller, you will NOT be able to downgrade to an earlier version.

3. Portal configuration will be lost after upgrading to Omada Controller 3.2.X from 2.4.X or earlier version.
Datum der Veröffentlichung: 2019-07-04 Sprache: Englisch Dateigröße: 124.2MB
Betriebssystem: Windows 7/8/10/Server

New Feature/Enhancement:

1. Optimize the performance of Controller to manage up to 1500 EAPs.

2. Optimize the interactive process between EAP and Controller to decrease the process time.

3. Limit the entry number of client/client history/guest to 1.2 million/1.2 million /6 million.

4. Optimize display page of map and log when there are a lot of entries.

 

Bug Fixed:

1. Fixed the bug that CPU and memory may be highly used when Fast Roaming is enabled.

2. Fixed the bug that Omada Controller reports timeout error when adopting multiple EAPs simultaneously.

3. Fixed the bug that Controller will print all Voucher codes even only some of the codes are selected.

 

Notes:

1. To use Omada Controller 3.2.x new features, you need to upgrade your EAP's firmware to the corresponding version.

2. Once upgraded to this version of Omada Controller, you will NOT be able to downgrade to an earlier version.

3. Portal configuration will be lost after upgrading to Omada Controller 3.2.X from 2.4.X or earlier version.
Datum der Veröffentlichung: 2019-03-08 Sprache: Englisch Dateigröße: 123.6MB
Betriebssystem: Windows 7/8/10/Server

New Feature/Enhancement:

1. Merge 2.4GHz and 5GHz SSID.

2. Add Guest Network function.

3. Optimize log field and content.

4. Add SSID Radius accounting to WPA-Enterprise security mode.

5. Optimize the site list which allows us to inquire the specific site based on the site name and add new entrance for the hotspot.

6. Add SSL encryption in Log Server, and Log setting/Mail Server can be only accessed by administrator account.

7. Add Layer-3 Accessibility in SSH.

8. Add Mesh settings to Backup and Restore file.

9. Add CHAP encryption and NAS ID in Radius portal authentication and the Radius Client role is transferred from EAP to Omada Controller.

10. Add SSID MAC Authentication to none security mode.

11. Add channel utilization function.

12. Add Full-Sector DFS function in Mesh network.

13. Channel limit is revised from private configuration to site settings.

14. Support inputting domain name in SMTP server.

 

Notes:

1. The log will be cleared when you upgrade the software from version 3.0.x to version 3.1.4.

2. Add push notification to Omada APP of version 2.1.4 or above when EAP is connected/disconnected from Omada Controller.

3. This version of Omada Controller is applied to Omada APP of version 2.1.4 or above.

4. When you upgrade your controller or backup files from lower version, the 2.4GHz and 5GHz SSID entries with the same name will be merged and it will inherit the parameters of the original 2.4GHz SSID.

5. If you use External Radius Server with External Web Portal in old version controller, pay attention that the API has been changed in this version, thus you have to modify your External Web Portal, refer to FAQ-2390 for more details.

6. The log generated by EAP will be managed and storaged by Controller if you manage EAPs by Omada Controller.

7. Channel utilization will take effect only with new firmware.
Datum der Veröffentlichung: 2019-03-08 Sprache: Englisch Dateigröße: 127.5MB
Betriebssystem: Windows 7/8/10/Server

New Feature/Enhancement:

1. Merge 2.4GHz and 5GHz SSID.

2. Add Guest Network function.

3. Optimize log field and content.

4. Add SSID Radius accounting to WPA-Enterprise security mode.

5. Optimize the site list which allows us to inquire the specific site based on the site name and add new entrance for the hotspot.

6. Add SSL encryption in Log Server, and Log setting/Mail Server can be only accessed by administrator account.

7. Add Layer-3 Accessibility in SSH.

8. Add Mesh settings to Backup and Restore file.

9. Add CHAP encryption and NAS ID in Radius portal authentication and the Radius Client role is transferred from EAP to Omada Controller.

10. Add SSID MAC Authentication to none security mode.

11. Add channel utilization function.

12. Add Full-Sector DFS function in Mesh network.

13. Channel limit is revised from private configuration to site settings.

14. Support inputting domain name in SMTP server.

 

Notes:

1. The log will be cleared when you upgrade the software from version 3.0.x to version 3.1.4.

2. Add push notification to Omada APP of version 2.1.4 or above when EAP is connected/disconnected from Omada Controller.

3. This version of Omada Controller is applied to Omada APP of version 2.1.4 or above.

4. When you upgrade your controller or backup files from lower version, the 2.4GHz and 5GHz SSID entries with the same name will be merged and it will inherit the parameters of the original 2.4GHz SSID.

5. If you use External Radius Server with External Web Portal in old version controller, pay attention that the API has been changed in this version, thus you have to modify your External Web Portal, refer to FAQ-2390 for more details.

6. The log generated by EAP will be managed and storaged by Controller if you manage EAPs by Omada Controller.

7. Channel utilization will take effect only with new firmware.

EAP Discovery Tool

Das EAP-Discovery-Tool sorgt dafür, dass der EAP-Controller Ihre EAPs auch bei Layer3-Management findet.

Weiterhin bietet es die Möglichkeit, die IP-Adresse eines EAPs herauszufinden.

Datum der Veröffentlichung: 2019-08-06 Sprache: Englisch Dateigröße: 25.85 MB
Betriebssystem: WinXP/Vista/7/8/8.1/10/Server2008/Server2012/Mac OS X 10.7/10.8/10.9/10.10/10.11

Bug fixed:

1. Fixed the bug that the Discovery Utility may fail to find EAPs.

2. Fixed the bug that the Cancel button may overlap with the display box after managing APs.

 

Note:

1. This version of software can be used in both Windows and Mac operation system.

2. Double click the software or run the command “java –jar **.jar” to run the software on MacOS (**.jar is the name of this software).

3. To run this software, you need to install JRE 8.0 on your PC first.
Datum der Veröffentlichung: 2019-06-14 Sprache: Englisch Dateigröße: 23.54 MB
Betriebssystem: WinXP/Vista/7/8/8.1/10/Server2008/Server2012/Mac OS X 10.7/10.8/10.9/10.10/10.11

Bug fixed:

1. Fixed the bug that when the Discovery Utility issues Controller_IP to EAPs which are in factory status, Controller cannot batch manage the EAPs.

2. Fixed the bug that sometimes the Discovery Utility cannot find all EAPs when running in MacOS.

Note:

1. This version of software can be used in both Windows and Mac operation system.

2. Double click the software or run the command “java –jar **.jar” to run the software on MacOS(**.jar is the name of this software).

3. To run this software, you need to install JRE 8.0 on your PC.
Datum der Veröffentlichung: 2018-07-24 Sprache: Englisch Dateigröße: 84.16 MB
Betriebssystem: Mac OS X 10.7/10.8/10.9/10.10/10.11

New Feature/Enhancement:
1. Change name to "Omada Discovery Utility".
2. Update background picture during installation.
3. Limit the maximum length of controller hostname to 79.
 
Bug Fixed:
Fix the bug that searching in the search box will cause the software to hang.
 
Note:
Operating System: Mac OS X 10.7/10.8/10.9/10.10/10.11.
Datum der Veröffentlichung: 2017-08-11 Sprache: Englisch Dateigröße: 3.39 MB
Betriebssystem: WinXP/Vista/7/8/8.1/10/Server2008/Server2012

GPL-Code

Emulatoren

Firmware-Version
(sechs- oder achtstellige Build-Nummer)
Working Mode
Sprache
170930(EU)
-
Englisch

Feature Filter: Alles EAP AdoptionPortalManagementQuick StartConfigurationConfiguration Example

Q&A

Feature Configuration Guide

T2700G-28TQ License Download
License Model: T2700G-28TQ-L1000

Find your product MAC and Serial Number.
License Key:
Product Serial Number:
Product MAC:
Checking code:

Newsletter abonnieren Für TP-Link ist Datenschutz sehr wichtig. Weitere Informationen zu unseren Datenschutzbedingungen finden Sie in der Datenschutzerklärung von TP-Link.

Folge uns

Über TP-Link
Informationen
Bezugsquellen
Product Catalogue
Learning Center
Deutschland / Deutsch
Copyright © 2020 TP-Link Technologies Co., Ltd. Alle Rechte vorbehalten.