Download für EAP225-Outdoor
- Produktübersicht
- Dokument
-
- Omada Controller Software 3.1.13_User Guide
- Omada Controller Software 3.2.1_User Guide
- Omada Controller Software 3.0.5_Windows/Linux_User Guide
- EAP225-Outdoor(EU)_V1_Installation Guide
- Omada Controller Software 3.1.4_User Guide
- Omada Controller Software 3.0.2_User Guide
- Omada Access Points_User Guide
1.0_1511143090094u.jpg)
AC1200-Dualband-Gigabit-WLAN-Outdoor-Accesspoint mit MU-MIMOSetup Video
-
How to manage TP-Link EAPs centrally via the Software Controller
This video demonstrates how to manage TP-Link EAPs centrally via the Software Controller. The setup consists of three steps:
• Install the Software
• Configure Discovery Utility (If your EAPs and the Controller Host are on different subnets)
• Configure Software Controller
THIS VIDEO APPLIES TO:
• All TP-Link EAP models (except EAP120 and EAP220)
• Omada Software Controller
• Mass EAPs (usually more than three)
Weitere Informationen
-
How to set up a TP Link EAP via your mobile phone
This video demonstrates how to set up a TP-Link EAP via your mobile phone. The setup consists of four steps:
• Connect the EAP to the network
• Download the Omada APP
• Connect to the EAP's wireless network
• Set up the EAP using the Omada APP
THIS VIDEO APPLIES TO:
• All TP-Link EAP models. (except EAP120 and EAP220)
• A small number (1-3) of EAPs.
Weitere Informationen
-
How to setup the OC200 via a web browser
This video will demonstrate how to set up the OC200 via a web browser. The setup consists of six steps:
• Connect the OC200 to your local network.
• Get ready for setup.
• Create a TP-Link ID.
• Log into your TP-Link ID.
• Add the OC200 to your TP-Link ID.
• Follow the wizard to set up the OC200.
THIS VIDEO APPLIES TO:
• All TP-Link EAP models (except EAP120 and EAP220)
• Omada Cloud Controller OC200
• Mass EAPs (usually more than three)
Weitere Informationen
-
How to setup the OC200 via your mobile phone
This video will demonstrate how to set up the OC200 via your mobile phone. You need to use the Omada APP to complete the setup. The setup consists of six steps:
• Connect the OC200 to your local network.
• Get ready for setup.
• Create a TP-Link ID.
• Log into your TP-Link ID.
• Add the OC200 to your TP-Link ID.
• Follow the wizard to set up the OC200.
THIS VIDEO APPLIES TO:
• All TP-Link EAP models (except EAP120 and EAP220)
• Omada Cloud Controller OC200
• Mass EAPs (usually more than three)
Weitere Informationen
-
How to manage TP-Link EAPs centrally from a remote place via a web browser
You can manage TP-Link EAPs at any time from anywhere with the Cloud Access function of our Omada Controller Software. This video introduces both the application scenario and concrete steps you can follow. Don't hesitate to give it a try.
THIS VIDEO APPLIES TO:
• All TP-Link EAP models (except EAP120 and EAP220)
• Omada Controller Software (version 3.0.2 or above)
• Mass EAPs (usually more than three)
Weitere Informationen
-
A Quick Overview of EAP Management Methods
This video introduces how to choose the optimum method to manage TP-Link EAPs in your scenario.
Here are 3 most common scenarios and their corresponding methods:
• Manage 1 or 2 EAPs locally
• Manage 3 or more EAPs locally
• Manage 3 or more EAPs remotely
When choosing the method, consider the following questions:
1. Standalone Mode or Controller Mode?
2. In Controller mode, what kind of controller will you use, an OC200 or a PC with Omada Software Controller?
3. What kind of user interface will you use, a web browser or the Omada app?
Weitere Informationen
-
How to Set up a TP-Link EAP via Web browser
This video will demonstrate how to set up a TP-Link EAP via a web browser. The setup consists of three steps:
1. Connect the EAP to the network
2. Log into the EAP (via a wired/wireless connection)
3. Change the default SSID
This video is suitable for users with a small number (1-3) of EAPs .
Weitere Informationen
Häufig gestellte Fragen
- How to manage EAPs at different places across internet using Omada Controller (via NAT Port Forwarding and EAP Discovery Utility)? (New UI)
- How to manage EAPs at different places across Internet using Omada Controller (via NAT Port Forwarding and DHCP Option 138)? (New UI)
- How to Install TP-Link Omada Discovery Utility on Windows and macOS PCs?
- Wie kann man EAPs in verschiedenen VLANs mit dem Omada Controller verwalten?
- Wie kann man EAPs an verschiedenen Standorten über das Internet mit dem EAP/Omada Controller verwalten (über NAT Port Forwarding für Controller Host mit DHCP Option138)?
- Wie man EAPs an verschiedenen Standorten über das Internet mit dem EAP-Controller verwaltet (über NAT Port Forwarding für Controller Host mit EAP Discover Utility).
- Wie kann man EAPs an verschiedenen Standorten über das Internet mit dem EAP/Omada Controller (über VPN Tunnel mit DHCP Option138) verwalten?
- How to manage EAPs at different sites across Internet using Omada Controller (via VPN Tunnel with EAP Discover Utility)? (Old UI)
- Wie kann man EAPs in verschiedenen Subnetzen mit dem EAP/Omada Controller (über DHCP Option 138) verwalten?
- Wie kann man EAPs in verschiedenen Subnetzen mit dem EAP/Omada-Controller (über das EAP Discover Utility) verwalten?
- How to manage EAPs in different subnets using Omada controller (via EAP Discovery Utility)? (New UI)
- Frequently Asked Questions about EAP Outdoor Products?
- Häufig gestellte Fragen zum EAP-Mesh-Netzwerk
- Fragen und Antworten für die TP-Link Omada Ap
- How to adopt EAP in Controller Mode?
- Wie kann man detaillierte Kundeninformationen zu einem EAP anzeigen?
- Was ist der Unterschied zwischen Login-Konto, Cloud-Konto, Gerätekonto und Benutzerkonto in Omada Controller?
- How to configure the WLAN Group function on the Software Controller (or OC200)
- Troubleshooting of Wireless Issues for Omada EAP Products
- How to back up and restore the configuration and data of your Software Controller (or OC200)
- What should I do when the controller fails to discover the EAP?
- Was ist "Airtime Fairness" bei TP-Link EAP/CAP?
- So wählen Sie EAP-Produkte aus
- Wie kann ich die Firmware meines EAP-Geräts über den Webbrowser aktualisieren?
- Wie finde ich die Firmware-Version meines EAP-Geräts?
- Was ist TP-Link EAP/CAP MU-MIMO?
- Wie konfiguriert man den Reboot-Zeitplan und die W-LAN-Zeitplanfunktion des Omada Controllers?
- Wie konfiguriert man den Load Balance Omada Controller
- So konfigurieren Sie die kostenlose Authentifizierungsrichtlinie für den EAP-Controller
- How to optimize wireless performance of EAP products
- Funktioniert die Konfiguration auch dann noch mit EAPs, wenn der Omada-Controller offline geht?
- So konfigurieren Sie den Omada-Controller als Windows-Dienst （höher als Controller 2.5.4）
- Was soll ich tun, wenn ich einen Zertifikatsfehler habe?
- Was ist Schnelles Roaming von TP-Link Business Wi-Fi-Produkten?
- So konfigurieren Sie mehrere SSIDs mit mehreren Subnetzen auf EAP-Produkten
- Was ist TP-Link EAP Beamforming?
- Wie konfiguriere ich die Voucher-Authentifizierung am Omada-Controller?
- The Requirements of Establishing an External Portal Server (above Omada Controller 2.6.0)
- What Can I Do If I Fail to Log In to the EAP via the Domain Name?
- Source code template for External Web Portal (Standalone Mode)
- How to Change the Language of the Printed Voucher Code？
- How to Configure Band Steering on TP-Link Omada Controller?
- Warum kann mein EAP-Controller einen EAP nicht übernehmen („Adopt“ schlägt fehl)?
Firmware
Ein Firmware-Update kann für Sie neue Funktionen und Fehlerbehebungen und Performanceverbesserungen bereithalten.
Zum Firmware-Upgrade
HINWEIS: Um Fehler bei der Aktualisierung zu vermeiden, lesen Sie sich bitte folgende Hinweise durch, bevor Sie das Upgrade tätigen.
- Bitte stellen Sie sicher, dass die Firmwareversion, die Sie zu installieren beabsichtigen, für Ihre Hardwareversion freigegeben ist. Eine nicht passende Firmware kann Ihr Gerät beschädigen und Ihren Anspruch auf Garantie erlöschen lassen. Normalerweise gilt V1.x=V1.
Es wird NICHT empfohlen, eine nicht für Ihren Standort vorgesehene Firmware zu installieren. Klicken Sie hier, um Ihren Standort zu wählen und dann eine geeignete Firmware herunterzuladen (z.B. bestehen Unterschiede zwischen der EU- und der US-Version) - Trennen Sie während des Upgradevorgangs KEINESFALLS die Spannungsversorgung.
- Aktualisieren Sie die Firmware NICHT über eine WLAN-Verbindung, außer Ihr Gerät verfügt über keinen Kabelanschluss.
- Es wird empfohlen, während des Upgrades keine Internetanwendungen auszuführen bzw. einfach vor dem Upgrade die Internetverbindung des Gerätes zu trennen.
- Verwenden Sie Entpack-Software wie WinZIP oder WinRAR, um die heruntergeladene Datei vor dem Upgrade zu entpacken.
| EAP225-Outdoor(EU)_V1_1.6.1 Build 20191022 | |||
|---|---|---|---|
| Datum der Veröffentlichung: 2019-12-25 | Sprache: Englisch | Dateigröße: 7.75 MB | |
|
|||
| EAP225-Outdoor(EU)_V1_1.6.0 Build 20190722 | |||
|---|---|---|---|
| Datum der Veröffentlichung: 2019-09-24 | Sprache: Englisch | Dateigröße: 7.74 MB | |
|
|||
| EAP225-Outdoor(EU)_V1_1.5.0 Build 20190404 | |||
|---|---|---|---|
| Datum der Veröffentlichung: 2019-05-05 | Sprache: Englisch | Dateigröße: 7.39 MB | |
|
|||
Verwendung von Third-Party-Firmware auf TP-Link-Produkten
Die Original-Firmware einiger TP-Link-Produkte kann durch Third-Party-Firmware wie DD-WRT ersetzt werden. TP-Link ist weder verpflichtet, für derart modifizierte Geräte Support oder Garantie zu leisten noch für deren Stabilität oder Leistungsfähigkeit zu garantieren. TP-Link wird keinerlei durch Third-Party-Firmware verursachte Schäden ersetzen.
Open-Source-Code für Entwickler (GPL)
Die folgenden Informationen sind für Entwickler gedacht und für die meisten Nutzer von TP-Link-Produkten uninteressant.
TP-Link-Produkte enthalten teilweise von Dritten entwickelten Softwarecode, darunter Code, der unter die GNU General Public Licence (“GPL“), Version 1/Version 2/Version 3 oder die GNU Lesser General Public License ("LGPL") gestellt ist. Diese Software können Sie unter Beachtung der damit verbundenen Bedingungen benutzen.
Sie können die GPL-Lizenzbedingungen hier ansehen, herunterladen und drucken. Sie bekommen die GPL-Sourcecodes der in TP-Link-Produkten verwendeten Software per Direktdownload sowie weitere Information, unter Anderem eine Liste der TP-Link-Software, welche GPL-Softwarecode enthält, unter GPL Code Center.
Diese Programme werden OHNE JEGLICHE GEWÄHRLEISTUNG weitergegeben. Auch die HERSTELLERGARANTIE und die GEWÄHRLEISTUNG gelten für diese nicht. Für Details sei auf die GNU General Public License verwiesen.
Controller Software
Der EAP-Controller ist dazu da, mehrere EAPs gemeinsam und zentral zu steuern.
| Datum der Veröffentlichung: 2020-01-21 | Sprache: Englisch | Dateigröße: 120.53MB |
Betriebssystem: Windows 7/8/10/Server |
||
New Feature/Enhancement: 1. Expand the number of Omada Controller’s User Account to 500. 2. Optimize the External Portal Server to support URL with parameters.
Notes: 1. To use Omada Controller 3.2.X new features, you need to upgrade your EAP's firmware to the corresponding version. 2. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version. 3. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.X or earlier version.
|
||
| Datum der Veröffentlichung: 2020-01-21 | Sprache: Englisch | Dateigröße: 124.45MB |
Betriebssystem: Windows 7/8/10/Server |
||
New Feature/Enhancement: 1. Expand the number of Omada Controller’s User Account to 500. 2. Optimize the External Portal Server to support URL with parameters.
Notes: 1. To use Omada Controller 3.2.X new features, you need to upgrade your EAP's firmware to the corresponding version. 2. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version. 3. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.X or earlier version. |
||
| Datum der Veröffentlichung: 2020-01-16 | Sprache: Englisch | Dateigröße: 123.35MB |
Betriebssystem: Ubuntu 14.04/16.04/17.04/18.04, CentOS 6.x/7.x and Fedora 20 or above, Debian 9.8. |
||
New Feature/Enhancement: 1. Change the mechanism that when adopting an EAP, the Controller will retain the IP configuration of EAP in Standalone mode. 2. Change the mechanism that multiple Omada Controllers can run on the same subnet. 3. Add the button of “Start Omada Controller after installation” and check it by default. 4. Extend the Max Associated Clients in Load Balance to 255. 5. Optimize the UI of Channel Utilization. 6. Optimize the authentication page of portal. 7. Optimize the UI of the portal that you cannot click Apply when you are uploading a photo. 8. Optimize the External Portal Server to support URL with parameters.
Bug Fixed: 1. Fixed the bug that the page of MAC filter may not display all groups when there are more than 5 groups. 2. Fixed the bug that after deleting a site, the Voucher code and Local user of this site still exist. 3. Fixed the bug that the site configuration will fail to restore when the imported site contains same Voucher code as the current Controller. 4. Fixed the bug that when mesh AP is powered off during upgrade, Controller may fail to upgrade other APs, with a prompt message “Other APs are upgrading”.
Notes: 1. To use new features on Omada Controller 3.2.x, you need to upgrade your EAP's firmware to the corresponding version. 2. The Omada Controller program needs to use the system's netstat command. If the Linux system does not have net-tools installed (which contain the netstat command), the program may not be able to run normally. 3. Support 64-bit Linux operating system including Ubuntu 14.04/16.04/17.04/18.04, CentOS 6.x/7.x and Fedora 20 or above, Debian 9.8. 4. Built-in JRE 1.8 Java environment. 5. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version. 6. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.8. 7. When upgrading from Controller 2.5.3 Linux to this version via install.sh, you need to uninstall old version of Controller first.
|
||
| Datum der Veröffentlichung: 2020-01-16 | Sprache: Englisch | Dateigröße: 99.4MB |
Betriebssystem: Ubuntu 14.04/16.04/17.04/18.04. |
||
New Feature/Enhancement: 1. Change the mechanism that when adopting an EAP, the Controller will retain the IP configuration of EAP in Standalone mode. 2. Change the mechanism that multiple Omada Controllers can run on the same subnet. 3. Add the button of “Start Omada Controller after installation” and check it by default. 4. Extend the Max Associated Clients in Load Balance to 255. 5. Optimize the UI of Channel Utilization. 6. Optimize the authentication page of portal. 7. Optimize the UI of the portal that you cannot click Apply when you are uploading a photo. 8. Optimize the External Portal Server to support URL with parameters.
Bug Fixed: 1. Fixed the bug that the page of MAC filter may not display all groups when there are more than 5 groups. 2. Fixed the bug that after deleting a site, the Voucher code and Local user of this site still exist. 3. Fixed the bug that the site configuration will fail to restore when the imported site contains same Voucher code as the current Controller. 4. Fixed the bug that when mesh AP is powered off during upgrade, Controller may fail to upgrade other APs, with a prompt message “Other APs are upgrading”.
Notes: 1. To use new features on Omada Controller 3.2.X, you need to upgrade your EAP's firmware to the corresponding version. 2. The Omada Controller program needs to use the system's netstat command. If the Linux system does not have net-tools installed (which contain the netstat command), the program may not be able to run normally. 3. Support 64-bit Linux operating system including Ubuntu 14.04/16.04/17.04/18.04. 4. Built-in JRE 1.8 Java environment. 5. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version. 6. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.8. |
||
| Datum der Veröffentlichung: 2020-01-09 | Sprache: Englisch | Dateigröße: 120.53MB |
Betriebssystem: Windows 7/8/10/Server |
||
New Feature/Enhancement: 1. Change the mechanism that when adopting an EAP, the Controller will retain the IP configuration of EAP in Standalone mode. 2. Change the mechanism that multiple Omada Controllers can run on the same subnet. 3. Add the button of “Start Omada Controller after installation” and check it by default. 4. Extend the Max Associated Clients in Load Balance to 255. 5. Optimize the UI of Channel Utilization. 6. Optimize the authentication page of portal. 7. Optimize the UI of the portal that you cannot click Apply when you are uploading a photo.
Bug Fixed: 1. Fixed the bug that the page of MAC filter may not display all groups when there are more than 5 groups. 2. Fixed the bug that after deleting a site, the Voucher code and Local user of this site still exist. 3. Fixed the bug that the site configuration will fail to restore when the imported site contains same Voucher code as the current Controller. 4. Fixed the bug that when mesh AP is powered off during upgrade, Controller may fail to upgrade other APs, with a prompt message “Other APs are upgrading”.
Notes: 1. To use Omada Controller 3.2.X new features, you need to upgrade your EAP's firmware to the corresponding version. 2. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version. 3. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.X or earlier version. |
||
| Datum der Veröffentlichung: 2020-01-09 | Sprache: Englisch | Dateigröße: 124.44MB |
Betriebssystem: Windows 7/8/10/Server |
||
New Feature/Enhancement: 1. Change the mechanism that when adopting an EAP, the Controller will retain the IP configuration of EAP in Standalone mode. 2. Change the mechanism that multiple Omada Controllers can run on the same subnet. 3. Add the button of “Start Omada Controller after installation” and check it by default. 4. Extend the Max Associated Clients in Load Balance to 255. 5. Optimize the UI of Channel Utilization. 6. Optimize the authentication page of portal. 7. Optimize the UI of the portal that you cannot click Apply when you are uploading a photo.
Bug Fixed: 1. Fixed the bug that the page of MAC filter may not display all groups when there are more than 5 groups. 2. Fixed the bug that after deleting a site, the Voucher code and Local user of this site still exist. 3. Fixed the bug that the site configuration will fail to restore when the imported site contains same Voucher code as the current Controller. 4. Fixed the bug that when mesh AP is powered off during upgrade, Controller may fail to upgrade other APs, with a prompt message “Other APs are upgrading”.
Notes: 1. To use Omada Controller 3.2.X new features, you need to upgrade your EAP's firmware to the corresponding version. 2. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version. 3. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.X or earlier version. |
||
| Datum der Veröffentlichung: 2019-11-08 | Sprache: Englisch | Dateigröße: 99.4MB |
Betriebssystem: Ubuntu 14.04/16.04/17.04/18.04 |
||
New Feature/Enhancement: 1. Add “Select Page” feature on voucher management page. 2. Change default status of “Terms of Service” on default portal page to uncheck. 3. Optimize the “Free Authentication Policy” to support URL with suffixes. 4. Change the default status of new added “Free Authentication Policy” to enable.
Bug Fixed: 1. Fixed the bug that when clients disconnect from the Facebook portal, the connection time and traffic usage of these clients may be zero in the log. 2. Fixed the bug that AP may disconnect from Omada Controller when it is upgrading the firmware. 3. Fixed the bug that in some cases, the channel configuration of 2.4G frequency may show up in 5G by mistake. 4. Fixed the bug that the configuration of SSID will not be issued correctly when changing the WLAN Group on the provisioning status.
Notes: 1. To use new features on Omada Controller 3.2.X, you need to upgrade your EAP's firmware to the corresponding version. 2. The Omada Controller program needs to use the system's netstat command. If the Linux system does not have net-tools installed (which contain the netstat command), the program may not be able to run normally. 3. Support 64-bit Linux operating system including Ubuntu 14.04/16.04/17.04/18.04. 4. Built-in JRE 1.8 Java environment. 5. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version. 6. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.8. |
||
| Datum der Veröffentlichung: 2019-11-08 | Sprache: Englisch | Dateigröße: 123.35MB |
Betriebssystem: Ubuntu 14.04/16.04/17.04/18.04, CentOS 6.x/7.x and Fedora 20 or above, Debian 9.8. |
||
New Feature/Enhancement: 1. Add “Select Page” feature on the management page of vouchers. 2. Change the default status of “Terms of Service” to uncheck. 3. Optimize the “Free Authentication Policy” to support URL with suffixes. 4. Change the default status of new added “Free Authentication Policy” to enable.
Bug Fixed: 1. Fixed the bug that when clients disconnect from the Facebook portal, the connection time and traffic usage of these clients may be zero in the log. 2. Fixed the bug that AP may disconnect from Omada Controller when it is upgrading the firmware. 3. Fixed the bug that in some cases, the channel configuration of 2.4G frequency may show up in 5G by mistake. 4. Fixed the bug that the configuration of SSID will not be issued correctly when changing the WLAN Group on the provisioning status.
Notes: 1. To use new features on Omada Controller 3.2.x, you need to upgrade your EAP's firmware to the corresponding version. 2. The Omada Controller program needs to use the system's netstat command. If the Linux system does not have net-tools installed (which contain the netstat command), the program may not be able to run normally. 3. Support 64-bit Linux operating system including Ubuntu 14.04/16.04/17.04/18.04, CentOS 6.x/7.x and Fedora 20 or above, Debian 9.8. 4. Built-in JRE 1.8 Java environment. 5. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version. 6. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.8. 7. When upgrading from Controller 2.5.3 Linux to this version via install.sh, you need to uninstall old version of Controller first. |
||
| Datum der Veröffentlichung: 2019-11-08 | Sprache: Englisch | Dateigröße: 120.52MB |
Betriebssystem: Windows 7/8/10/Server |
||
New Feature/Enhancement: 1. Add “Select Page” feature on the voucher management page. 2. Change the default status of “Terms of Service” on default portal page to uncheck. 3. Optimize the “Free Authentication Policy” to support URL with suffixes. 4. Change the default status of new added “Free Authentication Policy” to enable.
Bug Fixed: 1. Fixed the bug that when clients disconnect from the Facebook portal, the connection time and traffic usage of these clients may be zero in the log. 2. Fixed the bug that AP may disconnect from Omada Controller when it is upgrading the firmware. 3. Fixed the bug that in some cases, the channel configuration of 2.4G frequency may show up in 5G by mistake. 4. Fixed the bug that the configuration of SSID will not be issued correctly when changing the WLAN Group on the provisioning status.
Notes: 1. To use Omada Controller 3.2.x new features, you need to upgrade your EAP's firmware to the corresponding version. 2. Once upgraded to this version of Omada Controller, you will NOT be able to downgrade to an earlier version. 3. Portal configuration will be lost after upgrading to Omada Controller 3.2.X from 2.4.X or earlier version. 4. You are recommended to create a backup before upgrading, or you will not be permitted to install this version of Omada Controller. |
||
| Datum der Veröffentlichung: 2019-11-08 | Sprache: Englisch | Dateigröße: 124.43MB |
Betriebssystem: Windows 7/8/10/Server |
||
New Feature/Enhancement: 1. Add “Select Page” feature on the voucher management page. 2. Change the default status of “Terms of Service” on default portal page to uncheck. 3. Optimize the “Free Authentication Policy” to support URL with suffixes. 4. Change the default status of new added “Free Authentication Policy” to enable.
Bug Fixed: 1. Fixed the bug that when clients disconnect from the Facebook portal, the connection time and traffic usage of these clients may be zero in the log. 2. Fixed the bug that AP may disconnect from Omada Controller when it is upgrading the firmware. 3. Fixed the bug that in some cases, the channel configuration of 2.4G frequency may show up in 5G by mistake. 4. Fixed the bug that the configuration of SSID will not be issued correctly when changing the WLAN Group on the provisioning status.
Notes: 1. To use Omada Controller 3.2.x new features, you need to upgrade your EAP's firmware to the corresponding version. 2. Once upgraded to this version of Omada Controller, you will NOT be able to downgrade to an earlier version. 3. Portal configuration will be lost after upgrading to Omada Controller 3.2.X from 2.4.X or earlier version. 4. You are recommended to create a backup before upgrading, or you will not be permitted to install this version of Omada Controller. |
||
| Datum der Veröffentlichung: 2019-07-26 | Sprache: Englisch | Dateigröße: 99.23MB |
Betriebssystem: Ubuntu 14.04/16.04/17.04/18.04. |
||
New Feature/Enhancement: 1. Optimize the performance of Controller to manage up to 1500 EAPs. 2. Optimize the interactive process between EAP and Controller to decrease the processing time. 3. Limit the entry number of client/client history/guest to 1.2 million/1.2 million /6 million. 4. Optimize display page of map and log when there are a lot of entries.
Bug Fixed: 1. Fixed the bug that CPU and memory may be highly used when Fast Roaming is enabled. 2. Fixed the bug that Omada Controller reports timeout error when adopting multiple EAPs simultaneously. 3. Fixed the bug that Controller will print all Voucher codes even only some of the codes are selected.
Notes: 1. To use new features on Omada Controller 3.2.X, you need to upgrade your EAP's firmware to the corresponding version. 2. The Omada Controller program needs to use the system's netstat command. If the Linux system does not have net-tools installed (which contain the netstat command), the program may not be able to run normally. 3. Support 64-bit Linux operating system including Ubuntu 14.04/16.04/17.04/18.04. 4. Built-in JRE 1.8 Java environment. 5. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version. 6. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.8.
|
||
| Datum der Veröffentlichung: 2019-07-26 | Sprache: Englisch | Dateigröße: 123.15MB |
Betriebssystem: Ubuntu 14.04/16.04/17.04/18.04, CentOS 6.x/7.x and Fedora 20 or above, Debian 9.8. |
||
New Feature/Enhancement: 1. Optimize the performance of Controller to manage up to 1500 EAPs. 2. Optimize the interactive process between EAP and Controller to decrease the processing time. 3. Limit the entry number of client/client history/guest to 1.2 million/1.2 million /6 million. 4. Optimize display page of map and log when there are a lot of entries.
Bug Fixed: 1. Fixed the bug that CPU and memory may be highly used when Fast Roaming is enabled. 2. Fixed the bug that Omada Controller reports timeout error when adopting multiple EAPs simultaneously. 3. Fixed the bug that Controller will print all Voucher codes even only some of the codes are selected.
Notes: 1. To use new features on Omada Controller 3.2.x, you need to upgrade your EAP's firmware to the corresponding version. 2. The Omada Controller program needs to use the system's netstat command. If the Linux system does not have net-tools installed (which contain the netstat command), the program may not be able to run normally. 3. Support 64-bit Linux operating system including Ubuntu 14.04/16.04/17.04/18.04, CentOS 6.x/7.x and Fedora 20 or above, Debian 9.8. 4. Built-in JRE 1.8 Java environment. 5. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version. 6. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.8. 7. When upgrading from Controller 2.5.3 Linux to this version via install.sh, you need to uninstall old version of Controller first. |
||
| Datum der Veröffentlichung: 2019-07-04 | Sprache: Englisch | Dateigröße: 120.29MB |
Betriebssystem: Windows 7/8/10/Server |
||
New Feature/Enhancement: 1. Optimize the performance of Controller to manage up to 1500 EAPs. 2. Optimize the interactive process between EAP and Controller to decrease the process time. 3. Limit the entry number of client/client history/guest to 1.2 million/1.2 million /6 million. 4. Optimize display page of map and log when there are a lot of entries.
Bug Fixed: 1. Fixed the bug that CPU and memory may be highly used when Fast Roaming is enabled. 2. Fixed the bug that Omada Controller reports timeout error when adopting multiple EAPs simultaneously. 3. Fixed the bug that Controller will print all Voucher codes even only some of the codes are selected.
Notes: 1. To use Omada Controller 3.2.x new features, you need to upgrade your EAP's firmware to the corresponding version. 2. Once upgraded to this version of Omada Controller, you will NOT be able to downgrade to an earlier version. 3. Portal configuration will be lost after upgrading to Omada Controller 3.2.X from 2.4.X or earlier version. |
||
| Datum der Veröffentlichung: 2019-07-04 | Sprache: Englisch | Dateigröße: 124.2MB |
Betriebssystem: Windows 7/8/10/Server |
||
New Feature/Enhancement: 1. Optimize the performance of Controller to manage up to 1500 EAPs. 2. Optimize the interactive process between EAP and Controller to decrease the process time. 3. Limit the entry number of client/client history/guest to 1.2 million/1.2 million /6 million. 4. Optimize display page of map and log when there are a lot of entries.
Bug Fixed: 1. Fixed the bug that CPU and memory may be highly used when Fast Roaming is enabled. 2. Fixed the bug that Omada Controller reports timeout error when adopting multiple EAPs simultaneously. 3. Fixed the bug that Controller will print all Voucher codes even only some of the codes are selected.
Notes: 1. To use Omada Controller 3.2.x new features, you need to upgrade your EAP's firmware to the corresponding version. 2. Once upgraded to this version of Omada Controller, you will NOT be able to downgrade to an earlier version. 3. Portal configuration will be lost after upgrading to Omada Controller 3.2.X from 2.4.X or earlier version. |
||
| Datum der Veröffentlichung: 2019-05-28 | Sprache: Englisch | Dateigröße: 102.8MB |
Betriebssystem: Ubuntu 14.04/16.04/17.04/18.04 |
||
New Feature/Enhancement: 1. Add RADIUS Accounting. 2. Add Controller migrate and Site migrate. 3. Add log for some of portal authentication results. 4. Support POST request for External Web Portal. 5. Optimize Site Management to allow you to import site. 6. Optimize the performance when batch importing MAC address in MAC Filter.
Notes: 1. To use Omada Controller 3.1.X new features, you need to upgrade your EAP's firmware to the corresponding version. 2. The Omada Controller program needs to use the system's netstat command. If the Linux system does not have net-tools installed (which contain the netstat command), the program may run abnormally. 3. Supporting 64-bit Linux operating system, including Ubuntu 14.04/16.04/17.04/18.04. 4. Built-in JRE 1.8 Java environment. 5. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version. 6. Portal configuration will be lost after upgraded to Omada Controller 3.1.X from 2.4.8. 7. The log will be cleared when you upgrade the software from version 3.0.x to version 3.1.X. |
||
| Datum der Veröffentlichung: 2019-05-28 | Sprache: Englisch | Dateigröße: 129.13MB |
Betriebssystem: Ubuntu 14.04/16.04/17.04/18.04, CentOS 6.x/7.x and Fedora 20 or above, Debian 9.8 |
||
New Feature/Enhancement: 1. Add RADIUS Accounting. 2. Add Controller migrate and Site migrate. 3. Add log for some of portal authentication results. 4. Support POST request for External Web Portal. 5. Optimize Site Management to allow you to import site. 6. Optimize the performance when batch importing MAC address in MAC Filter.
Notes: 1. To use Omada Controller 3.1.X new features, you need to upgrade your EAP's firmware to the corresponding version. 2. The Omada Controller program needs to use the system's netstat command. If the Linux system does not have net-tools installed (which contain the netstat command), the program may run abnormally. 3. Supporting 64-bit Linux operating system, including Ubuntu 14.04/16.04/17.04/18.04, CentOS 6.x/7.x and Fedora 20 or above, Debian 9.8. 4. Built-in JRE 1.8 Java environment. 5. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version. 6. Portal configuration will be lost after upgraded to Omada Controller 3.1.X from 2.4.8. 7. The log will be cleared when you upgrade the software from version 3.0.x to version 3.1.X. 8. When upgrading from Controller 2.5.3 Linux to this version via install.sh, you need to uninstall old version of Controller first. |
||
| Datum der Veröffentlichung: 2019-03-25 | Sprache: Englisch | Dateigröße: 102.73MB |
Betriebssystem: Ubuntu 14.04/16.04/17.04/18.04 |
||
New Feature/Enhancement: 1. Merge 2.4GHz and 5GHz SSID. 2. Add Guest Network function. 3. Optimize log field and content. 4. Add SSID Radius accounting to WPA-Enterprise security mode. 5. Optimize the site list which allows us to inquire the specific site based on the site name and add new entrance for the hotspot. 6. Add SSL encryption in Log Server, and Log setting/Mail Server can be only accessed by administrator account. 7. Add Layer-3 Accessibility in SSH. 8. Add Mesh settings to Backup and Restore file. 9. Add CHAP encryption and NAS ID in Radius portal authentication and the Radius Client role is transferred from EAP to Omada Controller. 10. Add SSID MAC Authentication to none security mode. 11. Add channel utilization function. 12. Add Full-Sector DFS function in Mesh network. 13. Channel limit is revised from private configuration to site settings. 14. Support inputting domain name in SMTP server.
Notes: 1. To use Omada Controller 3.1.x new features, you need to upgrade your EAP's firmware to the corresponding version. 2. The Omada Controller program needs to use the system's netstat command. If the Linux system does not have net-tools installed (which contain the netstat command), the program may run abnormally. 3. Supporting 64-bit Linux operating system, including Ubuntu 14.04/16.04/17.04/18.04. 4. Built-in JRE 1.8 Java environment. 5. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version. 6. Portal configuration will be lost after upgraded to Omada Controller 3.1.X from 2.4.8. 7. The log will be cleared when you upgrade the software from version 3.0.x to version 3.1.4. 8. Add push notification to Omada APP of version 2.1.4 or above when EAP is connected/disconnected from Omada Controller. 9. This version of Omada Controller is applied to Omada APP of version 2.1.4 or above. 10. When you upgrade your controller or backup files from lower version, the 2.4GHz and 5GHz SSID entries with the same name will be merged and it will inherit the parameters of the original 2.4GHz SSID. 11. If you use External Radius Server with External Web Portal in old version controller, pay attention that the API has been changed in this version, thus you have to modify your External Web Portal, refer to FAQ-2390 for more details. 12. The log generated by EAP will be managed and storaged by Controller if you manage EAPs by Omada Controller. 13. Channel utilization will take effect only with new firmware. |
||
| Datum der Veröffentlichung: 2019-03-25 | Sprache: Englisch | Dateigröße: 129.07MB |
Betriebssystem: Ubuntu 14.04/16.04/17.04/18.04, CentOS 6.x/7.x and Fedora 20 or above, Debian 9.8 |
||
New Feature/Enhancement: 1. Merge 2.4GHz and 5GHz SSID. 2. Add Guest Network function. 3. Optimize log field and content. 4. Add SSID Radius accounting to WPA-Enterprise security mode. 5. Optimize the site list which allows us to inquire the specific site based on the site name and add new entrance for the hotspot. 6. Add SSL encryption in Log Server, and Log setting/Mail Server can be only accessed by administrator account. 7. Add Layer-3 Accessibility in SSH. 8. Add Mesh settings to Backup and Restore file. 9. Add CHAP encryption and NAS ID in Radius portal authentication and the Radius Client role is transferred from EAP to Omada Controller. 10. Add SSID MAC Authentication to none security mode. 11. Add channel utilization function. 12. Add Full-Sector DFS function in Mesh network. 13. Channel limit is revised from private configuration to site settings. 14. Support inputting domain name in SMTP server.
Notes: 1. To use Omada Controller 3.1.x new features, you need to upgrade your EAP's firmware to the corresponding version. 2. The Omada Controller program needs to use the system's netstat command. If the Linux system does not have net-tools installed (which contain the netstat command), the program may run abnormally. 3. Supporting 64-bit Linux operating system, including Ubuntu 14.04/16.04/17.04/18.04, CentOS 6.x/7.x and Fedora 20 or above, Debian 9.8. 4. Built-in JRE 1.8 Java environment. 5. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version. 6. Portal configuration will be lost after upgraded to Omada Controller 3.1.X from 2.4.8. 7. This version software needs you to install manually via curl command. 8. The log will be cleared when you upgrade the software from version 3.0.x to version 3.1.4. 9. Add push notification to Omada APP of version 2.1.4 or above when EAP is connected/disconnected from Omada Controller. 10. This version of Omada Controller is applied to Omada APP of version 2.1.4 or above. 11. When you upgrade your controller or backup files from lower version, the 2.4GHz and 5GHz SSID entries with the same name will be merged and it will inherit the parameters of the original 2.4GHz SSID. 12. If you use External Radius Server with External Web Portal in old version controller, pay attention that the API has been changed in this version, thus you have to modify your External Web Portal, refer to FAQ-2390 for more details. 13. The log generated by EAP will be managed and storaged by Controller if you manage EAPs by Omada Controller. 14. Channel utilization will take effect only with new firmware.
|
||
| Datum der Veröffentlichung: 2019-03-08 | Sprache: Englisch | Dateigröße: 123.6MB |
Betriebssystem: Windows 7/8/10/Server |
||
New Feature/Enhancement: 1. Merge 2.4GHz and 5GHz SSID. 2. Add Guest Network function. 3. Optimize log field and content. 4. Add SSID Radius accounting to WPA-Enterprise security mode. 5. Optimize the site list which allows us to inquire the specific site based on the site name and add new entrance for the hotspot. 6. Add SSL encryption in Log Server, and Log setting/Mail Server can be only accessed by administrator account. 7. Add Layer-3 Accessibility in SSH. 8. Add Mesh settings to Backup and Restore file. 9. Add CHAP encryption and NAS ID in Radius portal authentication and the Radius Client role is transferred from EAP to Omada Controller. 10. Add SSID MAC Authentication to none security mode. 11. Add channel utilization function. 12. Add Full-Sector DFS function in Mesh network. 13. Channel limit is revised from private configuration to site settings. 14. Support inputting domain name in SMTP server.
Notes: 1. The log will be cleared when you upgrade the software from version 3.0.x to version 3.1.4. 2. Add push notification to Omada APP of version 2.1.4 or above when EAP is connected/disconnected from Omada Controller. 3. This version of Omada Controller is applied to Omada APP of version 2.1.4 or above. 4. When you upgrade your controller or backup files from lower version, the 2.4GHz and 5GHz SSID entries with the same name will be merged and it will inherit the parameters of the original 2.4GHz SSID. 5. If you use External Radius Server with External Web Portal in old version controller, pay attention that the API has been changed in this version, thus you have to modify your External Web Portal, refer to FAQ-2390 for more details. 6. The log generated by EAP will be managed and storaged by Controller if you manage EAPs by Omada Controller. 7. Channel utilization will take effect only with new firmware. |
||
| Datum der Veröffentlichung: 2019-03-08 | Sprache: Englisch | Dateigröße: 127.5MB |
Betriebssystem: Windows 7/8/10/Server |
||
New Feature/Enhancement: 1. Merge 2.4GHz and 5GHz SSID. 2. Add Guest Network function. 3. Optimize log field and content. 4. Add SSID Radius accounting to WPA-Enterprise security mode. 5. Optimize the site list which allows us to inquire the specific site based on the site name and add new entrance for the hotspot. 6. Add SSL encryption in Log Server, and Log setting/Mail Server can be only accessed by administrator account. 7. Add Layer-3 Accessibility in SSH. 8. Add Mesh settings to Backup and Restore file. 9. Add CHAP encryption and NAS ID in Radius portal authentication and the Radius Client role is transferred from EAP to Omada Controller. 10. Add SSID MAC Authentication to none security mode. 11. Add channel utilization function. 12. Add Full-Sector DFS function in Mesh network. 13. Channel limit is revised from private configuration to site settings. 14. Support inputting domain name in SMTP server.
Notes: 1. The log will be cleared when you upgrade the software from version 3.0.x to version 3.1.4. 2. Add push notification to Omada APP of version 2.1.4 or above when EAP is connected/disconnected from Omada Controller. 3. This version of Omada Controller is applied to Omada APP of version 2.1.4 or above. 4. When you upgrade your controller or backup files from lower version, the 2.4GHz and 5GHz SSID entries with the same name will be merged and it will inherit the parameters of the original 2.4GHz SSID. 5. If you use External Radius Server with External Web Portal in old version controller, pay attention that the API has been changed in this version, thus you have to modify your External Web Portal, refer to FAQ-2390 for more details. 6. The log generated by EAP will be managed and storaged by Controller if you manage EAPs by Omada Controller. 7. Channel utilization will take effect only with new firmware. |
||
EAP Discovery Tool
Das EAP-Discovery-Tool sorgt dafür, dass der EAP-Controller Ihre EAPs auch bei Layer3-Management findet.
Weiterhin bietet es die Möglichkeit, die IP-Adresse eines EAPs herauszufinden.
| Datum der Veröffentlichung: 2019-08-06 | Sprache: Englisch | Dateigröße: 25.85 MB |
Betriebssystem: WinXP/Vista/7/8/8.1/10/Server2008/Server2012/Mac OS X 10.7/10.8/10.9/10.10/10.11 |
||
Bug fixed: 1. Fixed the bug that the Discovery Utility may fail to find EAPs. 2. Fixed the bug that the Cancel button may overlap with the display box after managing APs.
Note: 1. This version of software can be used in both Windows and Mac operation system. 2. Double click the software or run the command “java –jar **.jar” to run the software on MacOS (**.jar is the name of this software). 3. To run this software, you need to install JRE 8.0 on your PC first. |
||
| Datum der Veröffentlichung: 2019-06-14 | Sprache: Englisch | Dateigröße: 23.54 MB |
Betriebssystem: WinXP/Vista/7/8/8.1/10/Server2008/Server2012/Mac OS X 10.7/10.8/10.9/10.10/10.11 |
||
Bug fixed: 1. Fixed the bug that when the Discovery Utility issues Controller_IP to EAPs which are in factory status, Controller cannot batch manage the EAPs. 2. Fixed the bug that sometimes the Discovery Utility cannot find all EAPs when running in MacOS. Note: 1. This version of software can be used in both Windows and Mac operation system. 2. Double click the software or run the command “java –jar **.jar” to run the software on MacOS(**.jar is the name of this software). 3. To run this software, you need to install JRE 8.0 on your PC. |
||
| Datum der Veröffentlichung: 2018-07-24 | Sprache: Englisch | Dateigröße: 84.16 MB |
Betriebssystem: Mac OS X 10.7/10.8/10.9/10.10/10.11 |
||
New Feature/Enhancement: |
||
| Datum der Veröffentlichung: 2017-12-15 | Sprache: Englisch | Dateigröße: 3.39MB |
Betriebssystem: WinXP/Vista/7/8/8.1/10/Server2008/Server2012 |
||
Apps
- Omada APP
-
TP-Link Omada lets you configure settings, monitor network status and manage clients, all from the convenience of a smart phone or tablet. Learn more about Compatible Devices.
Note: To use Omada, please update your EAP's firmware to the latest version.
Emulatoren
Firmware-Version (sechs- oder achtstellige Build-Nummer) |
Working Mode |
Sprache |
|
|---|---|---|---|
180411(EU) |
- |
Englisch |
Q&A
Feature Configuration Guide
- Introduction of EAP Adoption
- Configuration Guide for Facebook Portal on Omada Controller 2.6.x
- How To Configure Cloud Access for Remote Management
- Methods for Managing the Omada EAPs Network
- Quick Start Guide_Standalone_EAP
- Managing System_Standalone EAP
- Managing EAP_Standalone EAP
- Configuring EAP_Standalone EAP
- Application Example_ Standalone EAP
- Configuration Guide for Facebook Portal on EAP Controller 2.5.x