Setup Video

  • How to manage TP-Link EAPs centrally via the Software Controller

    This video demonstrates how to manage TP-Link EAPs centrally via the Software Controller. The setup consists of three steps:
    • Install the Software
    • Configure Discovery Utility (If your EAPs and the Controller Host are on different subnets)
    • Configure Software Controller

    THIS VIDEO APPLIES TO:
    • All TP-Link EAP models (except EAP120 and EAP220)
    • Omada Software Controller
    • Mass EAPs (usually more than three)

    Weitere Informationen

  • How to set up a TP Link EAP via your mobile phone

    This video demonstrates how to set up a TP-Link EAP via your mobile phone. The setup consists of four steps:
    • Connect the EAP to the network
    • Download the Omada APP
    • Connect to the EAP's wireless network
    • Set up the EAP using the Omada APP

    THIS VIDEO APPLIES TO:
    • All TP-Link EAP models. (except EAP120 and EAP220)
    • A small number (1-3) of EAPs.

    Weitere Informationen

  • How to setup the OC200 via a web browser

    This video will demonstrate how to set up the OC200 via a web browser. The setup consists of six steps:
    • Connect the OC200 to your local network.
    • Get ready for setup.
    • Create a TP-Link ID.
    • Log into your TP-Link ID.
    • Add the OC200 to your TP-Link ID.
    • Follow the wizard to set up the OC200.

    THIS VIDEO APPLIES TO:
    • All TP-Link EAP models (except EAP120 and EAP220)
    • Omada Cloud Controller OC200
    • Mass EAPs (usually more than three)

    Weitere Informationen

  • How to setup the OC200 via your mobile phone

    This video will demonstrate how to set up the OC200 via your mobile phone. You need to use the Omada APP to complete the setup. The setup consists of six steps:
    • Connect the OC200 to your local network.
    • Get ready for setup.
    • Create a TP-Link ID.
    • Log into your TP-Link ID.
    • Add the OC200 to your TP-Link ID.
    • Follow the wizard to set up the OC200.
    THIS VIDEO APPLIES TO:
    • All TP-Link EAP models (except EAP120 and EAP220)
    • Omada Cloud Controller OC200
    • Mass EAPs (usually more than three)

    Weitere Informationen

  • How to manage TP-Link EAPs centrally from a remote place via a web browser

    You can manage TP-Link EAPs at any time from anywhere with the Cloud Access function of our Omada Controller Software. This video introduces both the application scenario and concrete steps you can follow. Don't hesitate to give it a try.
    THIS VIDEO APPLIES TO:
    • All TP-Link EAP models (except EAP120 and EAP220)
    • Omada Controller Software (version 3.0.2 or above)
    • Mass EAPs (usually more than three)

    Weitere Informationen

  • A Quick Overview of EAP Management Methods

    This video introduces how to choose the optimum method to manage TP-Link EAPs in your scenario.
    Here are 3 most common scenarios and their corresponding methods:
    • Manage 1 or 2 EAPs locally
    • Manage 3 or more EAPs locally
    • Manage 3 or more EAPs remotely
    When choosing the method, consider the following questions:
    1. Standalone Mode or Controller Mode?
    2. In Controller mode, what kind of controller will you use, an OC200 or a PC with Omada Software Controller?
    3. What kind of user interface will you use, a web browser or the Omada app?

    Weitere Informationen

  • How to Set up a TP-Link EAP via Web browser

    This video will demonstrate how to set up a TP-Link EAP via a web browser. The setup consists of three steps:
    1. Connect the EAP to the network
    2. Log into the EAP (via a wired/wireless connection)
    3. Change the default SSID
    This video is suitable for users with a small number (1-3) of EAPs .

    Weitere Informationen

Häufig gestellte Fragen

Firmware

Ein Firmware-Update kann für Sie neue Funktionen und Fehlerbehebungen und Performanceverbesserungen bereithalten.

Zum Firmware-Upgrade

HINWEIS: Um Fehler bei der Aktualisierung zu vermeiden, lesen Sie sich bitte folgende Hinweise durch, bevor Sie das Upgrade tätigen.

  • Bitte stellen Sie sicher, dass die Firmwareversion, die Sie zu installieren beabsichtigen, für Ihre Hardwareversion freigegeben ist. Eine nicht passende Firmware kann Ihr Gerät beschädigen und Ihren Anspruch auf Garantie erlöschen lassen. Normalerweise gilt V1.x=V1.
    Es wird NICHT empfohlen, eine nicht für Ihren Standort vorgesehene Firmware zu installieren. Klicken Sie hier, um Ihren Standort zu wählen und dann eine geeignete Firmware herunterzuladen (z.B. bestehen Unterschiede zwischen der EU- und der US-Version)
  • Trennen Sie während des Upgradevorgangs KEINESFALLS die Spannungsversorgung.
  • Aktualisieren Sie die Firmware NICHT über eine WLAN-Verbindung, außer Ihr Gerät verfügt über keinen Kabelanschluss.
  • Es wird empfohlen, während des Upgrades keine Internetanwendungen auszuführen bzw. einfach vor dem Upgrade die Internetverbindung des Gerätes zu trennen.
  • Verwenden Sie Entpack-Software wie WinZIP oder WinRAR, um die heruntergeladene Datei vor dem Upgrade zu entpacken.
EAP225-Outdoor(EU)_V1_1.6.0 Build 20190722
Datum der Veröffentlichung: 2019-09-24 Sprache: Englisch Dateigröße: 7.74 MB

Recommended Controller Software Version: Omada Controller v3.2.x or above

 

New Feature/Enhancement:

1. Change the OpenSSL version to 1.0.2q.

2. Optimize UI, including character optimization and display error correction.

3. Update the time zone of Caracas from GMT-4:30 to GMT-4:00.

 

Bug Fixed:

1. Fixed the bug that client devices can pass the portal authentication after disconnected from the Controller.

2. Fixed the bug that untag packets can be transferred to SSIDs with different VLANs.

3. Fixed the bug that mesh AP may disconnect from the Controller after long-time running.

4. Fixed the bug that fast roaming may not take effect in some mesh network.

5. Fixed the bug that some EAPs may disconnect from the Omada Controller in large scale network.

6. Fixed the bug that the management page may not be accessed after EAP is disconnected from the Controller.

7. Fixed the bug that when APs are disconnected from Controller, the rate limit configuration will be not issued to these APs after they are back to connected again.

8. Fixed the bug that when the time of EAP is synchronized with PC, it will be the same as PC’s time not considering different time zones.

9. Fixed the bug that packets with VLAN tag can be forwarded to the SSID without wireless VLAN setting.

 

Notes:

1. For EAP225-Outdoor v1 only.

2. Your device's configuration won't be lost after upgrading.

3. This version of firmware is applied to Omada APP of version 2.1.X or above.

Verwendung von Third-Party-Firmware auf TP-Link-Produkten

Die Original-Firmware einiger TP-Link-Produkte kann durch Third-Party-Firmware wie DD-WRT ersetzt werden. TP-Link ist weder verpflichtet, für derart modifizierte Geräte Support oder Garantie zu leisten noch für deren Stabilität oder Leistungsfähigkeit zu garantieren. TP-Link wird keinerlei durch Third-Party-Firmware verursachte Schäden ersetzen.

Open-Source-Code für Entwickler (GPL)

Die folgenden Informationen sind für Entwickler gedacht und für die meisten Nutzer von TP-Link-Produkten uninteressant.

TP-Link-Produkte enthalten teilweise von Dritten entwickelten Softwarecode, darunter Code, der unter die GNU General Public Licence (“GPL“), Version 1/Version 2/Version 3 oder die GNU Lesser General Public License ("LGPL") gestellt ist. Diese Software können Sie unter Beachtung der damit verbundenen Bedingungen benutzen.

Sie können die GPL-Lizenzbedingungen hier ansehen, herunterladen und drucken. Sie bekommen die GPL-Sourcecodes der in TP-Link-Produkten verwendeten Software per Direktdownload sowie weitere Information, unter Anderem eine Liste der TP-Link-Software, welche GPL-Softwarecode enthält, unter GPL Code Center.

Diese Programme werden OHNE JEGLICHE GEWÄHRLEISTUNG weitergegeben. Auch die HERSTELLERGARANTIE und die GEWÄHRLEISTUNG gelten für diese nicht. Für Details sei auf die GNU General Public License verwiesen.

Controller Software

The EAP Controller is used to manage multiple EAPs intensively.

Datum der Veröffentlichung: 2019-07-04 Sprache: Englisch Dateigröße: 120.29MB
Betriebssystem: Windows 7/8/10/Server

New Feature/Enhancement:

1. Optimize the performance of Controller to manage up to 1500 EAPs.

2. Optimize the interactive process between EAP and Controller to decrease the process time.

3. Limit the entry number of client/client history/guest to 1.2 million/1.2 million /6 million.

4. Optimize display page of map and log when there are a lot of entries.

 

Bug Fixed:

1. Fixed the bug that CPU and memory may be highly used when Fast Roaming is enabled.

2. Fixed the bug that Omada Controller reports timeout error when adopting multiple EAPs simultaneously.

3. Fixed the bug that Controller will print all Voucher codes even only some of the codes are selected.

 

Notes:

1. To use Omada Controller 3.2.x new features, you need to upgrade your EAP's firmware to the corresponding version.

2. Once upgraded to this version of Omada Controller, you will NOT be able to downgrade to an earlier version.

3. Portal configuration will be lost after upgrading to Omada Controller 3.2.X from 2.4.X or earlier version.

Datum der Veröffentlichung: 2019-07-04 Sprache: Englisch Dateigröße: 124.2MB
Betriebssystem: Windows 7/8/10/Server

New Feature/Enhancement:

1. Optimize the performance of Controller to manage up to 1500 EAPs.

2. Optimize the interactive process between EAP and Controller to decrease the process time.

3. Limit the entry number of client/client history/guest to 1.2 million/1.2 million /6 million.

4. Optimize display page of map and log when there are a lot of entries.

 

Bug Fixed:

1. Fixed the bug that CPU and memory may be highly used when Fast Roaming is enabled.

2. Fixed the bug that Omada Controller reports timeout error when adopting multiple EAPs simultaneously.

3. Fixed the bug that Controller will print all Voucher codes even only some of the codes are selected.

 

Notes:

1. To use Omada Controller 3.2.x new features, you need to upgrade your EAP's firmware to the corresponding version.

2. Once upgraded to this version of Omada Controller, you will NOT be able to downgrade to an earlier version.

3. Portal configuration will be lost after upgrading to Omada Controller 3.2.X from 2.4.X or earlier version.

EAP Discovery Tool

The EAP Discovery Tool can help the EAP Controller to adopt the EAP in L3 Network, and you can also use the EAP Discovery Tool to find the EAP’s IP address.

Datum der Veröffentlichung: 2019-06-14 Sprache: Englisch Dateigröße: 23.54 MB
Betriebssystem: WinXP/Vista/7/8/8.1/10/Server2008/Server2012/Mac OS X 10.7/10.8/10.9/10.10/10.11

Bug fixed:

1. Fixed the bug that when the Discovery Utility issues Controller_IP to EAPs which are in factory status, Controller cannot batch manage the EAPs.

2. Fixed the bug that sometimes the Discovery Utility cannot find all EAPs when running in MacOS.

Note:

1. This version of software can be used in both Windows and Mac operation system.

2. Double click the software or run the command “java –jar **.jar” to run the software on MacOS(**.jar is the name of this software).

3. To run this software, you need to install JRE 8.0 on your PC.

T2700G-28TQ License Download
License Model: T2700G-28TQ-L1000

Find your product MAC and Serial Number.
License Key:
Product Serial Number:
Product MAC:
Checking code:

Subscription Für TP-Link ist Datenschutz sehr wichtig. Weitere Informationen zu unseren Datenschutzbedingungen finden Sie in der Datenschutzerklärung von TP-Link.

From United States (English)?

Check products and services for your region.