Download for EAP110 V4

Please choose hardware version:

V4

>How to find the hardware version on a TP-Link device?

IMPORTANT: Model and hardware version availability varies by region. Please refer to your TP-Link regional website to determine product availability.
Product Overview
Manual
300Mbps Wireless N Ceiling Mount Access Point
EAP110

Setup Video

  • How to manage TP-Link EAPs centrally via the Software Controller

    This video demonstrates how to manage TP-Link EAPs centrally via the Software Controller. The setup consists of three steps:
    • Install the Software
    • Configure Discovery Utility (If your EAPs and the Controller Host are on different subnets)
    • Configure Software Controller

    THIS VIDEO APPLIES TO:
    • All TP-Link EAP models (except EAP120 and EAP220)
    • Omada Software Controller
    • Mass EAPs (usually more than three)

    Learn More

  • How to set up a TP Link EAP via your mobile phone

    This video demonstrates how to set up a TP-Link EAP via your mobile phone. The setup consists of four steps:
    • Connect the EAP to the network
    • Download the Omada APP
    • Connect to the EAP's wireless network
    • Set up the EAP using the Omada APP

    THIS VIDEO APPLIES TO:
    • All TP-Link EAP models. (except EAP120 and EAP220)
    • A small number (1-3) of EAPs.

    Learn More

  • How to setup the OC200 via a web browser

    This video will demonstrate how to set up the OC200 via a web browser. The setup consists of six steps:
    • Connect the OC200 to your local network.
    • Get ready for setup.
    • Create a TP-Link ID.
    • Log into your TP-Link ID.
    • Add the OC200 to your TP-Link ID.
    • Follow the wizard to set up the OC200.

    THIS VIDEO APPLIES TO:
    • All TP-Link EAP models (except EAP120 and EAP220)
    • Omada Cloud Controller OC200
    • Mass EAPs (usually more than three)

    Learn More

  • How to setup the OC200 via your mobile phone

    This video will demonstrate how to set up the OC200 via your mobile phone. You need to use the Omada APP to complete the setup. The setup consists of six steps:
    • Connect the OC200 to your local network.
    • Get ready for setup.
    • Create a TP-Link ID.
    • Log into your TP-Link ID.
    • Add the OC200 to your TP-Link ID.
    • Follow the wizard to set up the OC200.
    THIS VIDEO APPLIES TO:
    • All TP-Link EAP models (except EAP120 and EAP220)
    • Omada Cloud Controller OC200
    • Mass EAPs (usually more than three)

    Learn More

  • How to manage TP-Link EAPs centrally from a remote place via a web browser

    You can manage TP-Link EAPs at any time from anywhere with the Cloud Access function of our Omada Controller Software. This video introduces both the application scenario and concrete steps you can follow. Don't hesitate to give it a try.
    THIS VIDEO APPLIES TO:
    • All TP-Link EAP models (except EAP120 and EAP220)
    • Omada Controller Software (version 3.0.2 or above)
    • Mass EAPs (usually more than three)

    Learn More

  • A Quick Overview of EAP Management Methods

    This video introduces how to choose the optimum method to manage TP-Link EAPs in your scenario.
    Here are 3 most common scenarios and their corresponding methods:
    • Manage 1 or 2 EAPs locally
    • Manage 3 or more EAPs locally
    • Manage 3 or more EAPs remotely
    When choosing the method, consider the following questions:
    1. Standalone Mode or Controller Mode?
    2. In Controller mode, what kind of controller will you use, an OC200 or a PC with Omada Software Controller?
    3. What kind of user interface will you use, a web browser or the Omada app?

    Learn More

  • How to Set up a TP-Link EAP via Web browser

    This video will demonstrate how to set up a TP-Link EAP via a web browser. The setup consists of three steps:
    1. Connect the EAP to the network
    2. Log into the EAP (via a wired/wireless connection)
    3. Change the default SSID
    This video is suitable for users with a small number (1-3) of EAPs .

    Learn More

Feature Filter: All Q&A of functional explanation or specification parametersConfiguration GuideUser Application RequirementTroubleshooting

FAQs

Firmware

A firmware update can resolve issues that the previous firmware version may have and improve its current performance.

To Upgrade

IMPORTANT: To prevent upgrade failures, please read the following before proceeding with the upgrade process

  • Please upgrade firmware from the local TP-Link official website of the purchase location for your TP-Link device, otherwise it will be against the warranty. Please click here to change site if necessary.
  • Please verify the hardware version of your device for the firmware version. Wrong firmware upgrade may damage your device and void the warranty. （Normally V1.x=V1）
    How to find the hardware version on a TP-Link device?
  • Do NOT turn off the power during the upgrade process, as it may cause permanent damage to the product.
  • To avoid wireless disconnect issue during firmware upgrade process, it's recommended to upload firmware with wired connection unless there is no LAN/Ethernet port on your TP-Link device.
  • It's recommended that users stop all Internet applications on the computer, or simply disconnect Internet line from the device before the upgrade.
  • Use decompression software such as WinZIP or WinRAR to extract the file you download before the upgrade.
EAP110(EU)_V4_3.5.0 Build 20200113
Published Date: 2020-03-04 Language: English File Size: 5.91 MB

Recommended Controller Software Version: Omada Controller v3.2.6 or above

 

New Feature/Enhancement:

1. Change the mechanism that the IP configuration in Standalone mode will be retained after the EAP is adopted by the Controller.

2. Add anti-brute force cracking mechanism that you cannot login to the EAP via SSH or webserver in two hours if you fail to login up to 30 times in half an hour.

3. Optimize NTP server to support domain name.

4. Change the “Term of Service” of portal settings page in standalone mode as unchecked by default.

5. Optimize the UI of SSID and Free Authentication Policy in Standalone mode.

6. Optimize the DNS resolution process of EAP to avoid parsing wrong IP.

7. Reduce the time interval to 5s and limit the size to 2k bytes of the More Client Detail Log in Log Settings.

8. Change the OpenSSL version to 1.0.2q.

9. Optimize UI, including character optimization and display error correction.

10. Update the time zone of Caracas from GMT-4:30 to GMT-4:00.

 

Bug Fixed:

1. Fixed the bug that client devices can pass the portal authentication after disconnected from the Controller.

2. Fixed the bug that untagged packets can be transferred to SSIDs with different VLANs.

3. Fixed the bug that packets with VLAN tag can be forwarded to the SSID without wireless VLAN setting.

4. Fixed the bug that External Radius Server portal page may not pop up in some clients.

5. Fixed the bug that when adding an SSID with no password and change the encryption mode to WPA on Omada APP, the clients can still connect to the SSID without password.

6. Fixed the bug that the management page may not be accessed after EAP is disconnected from the Controller.

7. Fixed the bug that when APs are disconnected from Controller, the rate limit configuration will be not issued to these APs after they are back to connected again.

8. Fixed the bug that the EAP may hang after clicking save in wireless VLAN page in Standalone mode.

9. Fixed the bug that the EAP may hang if scanning rogue AP in high frequency.

10. Fixed the bug that when the time of EAP is synchronized with PC, it will be the same as PC’s time not considering different time zones.

 

Notes:

1. For EAP110 v4 only.

2. Your device's configuration won't be lost after upgrading.

3. This version of firmware is applied to Omada APP of version 2.1.X or above.

4. You cannot downgrade if you upgrade from the firmware released in 2018 or earlier to this version directly.
EAP110(EU)_V4_3.4.0 Build 20191014
Published Date: 2020-01-14 Language: English File Size: 5.70 MB

Recommended Controller Software Version: Omada Controller v3.2.x or above

Bug Fixed:
1. Fixed the bug that the CPU usage of EAP may be high when EAPs are deployed densely.
2. Fixed the bug that EAP may disconnect from Omada Controller when EAPs are deployed densely. 

Notes:
1. For EAP110 v4 only.
2. Your device's configuration won't be lost after upgrading.
3. This version of firmware is applied to Omada APP of version 2.1.X or above.

4. You cannot downgrade if you upgrade from 2018 or older firmware to this version directly.
EAP110(EU)_V4_3.3.0 Build 20190301
Published Date: 2019-04-11 Language: English File Size: 5.70 MB

Recommended Controller Software Version: Omada Controller v3.1.x or above

 

New Feature/Enhancement:

1. Add Radius Accounting to External Radius Server in standalone mode.

2. Add SSID Radius accounting to WPA-Enterprise security mode.

3. Add SSL encryption in Auto Mail of Log Settings.

4. Support the feature of merging 2.4GHz and 5GHz SSID with Controller 3.1.4.

5. Support SSID MAC Authentication to none security mode with Controller 3.1.4.

6. Support channel utilization function with Controller 3.1.4.

7. Support Layer-3 Accessibility in SSH with Controller 3.1.4.

8. Change the rule of the LED when resetting/rebooting EAP.

 

Notes:

1. For EAP110 v4 only.

2. Your device's configuration won't be lost after upgrading.

3. This version of firmware is applied to Omada APP of version 2.1.X or above.

To Use Third Party Firmware In TP-Link Products

Some official firmware of TP-Link products can be replaced by the third party firmware such as DD-WRT. TP-Link is not obligated to provide any maintenance or support for it, and does not guarantee the performance and stability of third party firmware. Damage to the product as a result of using third party firmware will void the product's warranty.

Open Source Code For Programmers (GPL)

Please note: The products of TP-Link partly contain software code developed by third parties, including software code subject to the GNU General Public Licence (“GPL“), Version 1/Version 2/Version 3 or GNU Lesser General Public License ("LGPL"). You may use the respective software condition to following the GPL licence terms.

You can review, print and download the respective GPL licence terms here. You receive the GPL source codes of the respective software used in TP-Link products for direct download and further information, including a list of TP-Link software that contain GPL software code under GPL Code Center.

The respective programs are distributed WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the respective GNU General Public License for more details.

Controller Software

The EAP Controller is used to manage multiple EAPs intensively.

Published Date: 2020-01-21 Language: English File Size: 120.53MB
Operating System: Windows 7/8/10/Server

New Feature/Enhancement:

1. Expand the number of Omada Controller’s User Account to 500.  

2. Optimize the External Portal Server to support URL with parameters.

 

Notes:

1. To use Omada Controller 3.2.X new features, you need to upgrade your EAP's firmware to the corresponding version.

2. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

3. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.X or earlier version.

 
Published Date: 2020-01-21 Language: English File Size: 124.45MB
Operating System: Windows 7/8/10/Server

New Feature/Enhancement:

1. Expand the number of Omada Controller’s User Account to 500.  

2. Optimize the External Portal Server to support URL with parameters.

 

Notes:

1. To use Omada Controller 3.2.X new features, you need to upgrade your EAP's firmware to the corresponding version.

2. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

3. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.X or earlier version.
Published Date: 2020-01-16 Language: English File Size: 123.35MB
Operating System: Ubuntu 14.04/16.04/17.04/18.04, CentOS 6.x/7.x and Fedora 20 or above, Debian 9.8.

New Feature/Enhancement:

1. Change the mechanism that when adopting an EAP, the Controller will retain the IP configuration of EAP in Standalone mode.

2. Change the mechanism that multiple Omada Controllers can run on the same subnet.

3. Add the button of “Start Omada Controller after installation” and check it by default.

4. Extend the Max Associated Clients in Load Balance to 255.

5. Optimize the UI of Channel Utilization.

6. Optimize the authentication page of portal.

7. Optimize the UI of the portal that you cannot click Apply when you are uploading a photo.

8. Optimize the External Portal Server to support URL with parameters.

 

Bug Fixed:

1. Fixed the bug that the page of MAC filter may not display all groups when there are more than 5 groups.

2. Fixed the bug that after deleting a site, the Voucher code and Local user of this site still exist.

3. Fixed the bug that the site configuration will fail to restore when the imported site contains same Voucher code as the current Controller.

4. Fixed the bug that when mesh AP is powered off during upgrade, Controller may fail to upgrade other APs, with a prompt message “Other APs are upgrading”.

 

Notes:

1. To use new features on Omada Controller 3.2.x, you need to upgrade your EAP's firmware to the corresponding version.

2. The Omada Controller program needs to use the system's netstat command. If the Linux system does not have net-tools installed (which contain the netstat command), the program may not be able to run normally.

3. Support 64-bit Linux operating system including Ubuntu 14.04/16.04/17.04/18.04, CentOS 6.x/7.x and Fedora 20 or above, Debian 9.8.

4. Built-in JRE 1.8 Java environment.

5. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

6. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.8.

7. When upgrading from Controller 2.5.3 Linux to this version via install.sh, you need to uninstall old version of Controller first.

 
Published Date: 2020-01-16 Language: English File Size: 99.4MB
Operating System: Ubuntu 14.04/16.04/17.04/18.04/Debian 9.8

New Feature/Enhancement:

1. Change the mechanism that when adopting an EAP, the Controller will retain the IP configuration of EAP in Standalone mode.

2. Change the mechanism that multiple Omada Controllers can run on the same subnet.

3. Add the button of “Start Omada Controller after installation” and check it by default.

4. Extend the Max Associated Clients in Load Balance to 255.

5. Optimize the UI of Channel Utilization.

6. Optimize the authentication page of portal.

7. Optimize the UI of the portal that you cannot click Apply when you are uploading a photo.

8. Optimize the External Portal Server to support URL with parameters.

 

Bug Fixed:

1. Fixed the bug that the page of MAC filter may not display all groups when there are more than 5 groups.

2. Fixed the bug that after deleting a site, the Voucher code and Local user of this site still exist.

3. Fixed the bug that the site configuration will fail to restore when the imported site contains same Voucher code as the current Controller.

4. Fixed the bug that when mesh AP is powered off during upgrade, Controller may fail to upgrade other APs, with a prompt message “Other APs are upgrading”.

 

Notes:

1. To use new features on Omada Controller 3.2.X, you need to upgrade your EAP's firmware to the corresponding version.

2. The Omada Controller program needs to use the system's netstat command. If the Linux system does not have net-tools installed (which contain the netstat command), the program may not be able to run normally.

3. Support 64-bit Linux operating system including Ubuntu 14.04/16.04/17.04/18.04/Debian 9.8

4. Built-in JRE 1.8 Java environment.

5. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

6. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.8.
Published Date: 2020-01-09 Language: English File Size: 120.53MB
Operating System: Windows 7/8/10/Server

New Feature/Enhancement:

1. Change the mechanism that when adopting an EAP, the Controller will retain the IP configuration of EAP in Standalone mode.

2. Change the mechanism that multiple Omada Controllers can run on the same subnet.

3. Add the button of “Start Omada Controller after installation” and check it by default.

4. Extend the Max Associated Clients in Load Balance to 255.

5. Optimize the UI of Channel Utilization.

6. Optimize the authentication page of portal.

7. Optimize the UI of the portal that you cannot click Apply when you are uploading a photo.

 

Bug Fixed:

1. Fixed the bug that the page of MAC filter may not display all groups when there are more than 5 groups.

2. Fixed the bug that after deleting a site, the Voucher code and Local user of this site still exist.

3. Fixed the bug that the site configuration will fail to restore when the imported site contains same Voucher code as the current Controller.

4. Fixed the bug that when mesh AP is powered off during upgrade, Controller may fail to upgrade other APs, with a prompt message “Other APs are upgrading”.

 

Notes:

1. To use Omada Controller 3.2.X new features, you need to upgrade your EAP's firmware to the corresponding version.

2. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

3. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.X or earlier version.
Published Date: 2020-01-09 Language: English File Size: 124.44MB
Operating System: Windows 7/8/10/Server

New Feature/Enhancement:

1. Change the mechanism that when adopting an EAP, the Controller will retain the IP configuration of EAP in Standalone mode.

2. Change the mechanism that multiple Omada Controllers can run on the same subnet.

3. Add the button of “Start Omada Controller after installation” and check it by default.

4. Extend the Max Associated Clients in Load Balance to 255.

5. Optimize the UI of Channel Utilization.

6. Optimize the authentication page of portal.

7. Optimize the UI of the portal that you cannot click Apply when you are uploading a photo.

 

Bug Fixed:

1. Fixed the bug that the page of MAC filter may not display all groups when there are more than 5 groups.

2. Fixed the bug that after deleting a site, the Voucher code and Local user of this site still exist.

3. Fixed the bug that the site configuration will fail to restore when the imported site contains same Voucher code as the current Controller.

4. Fixed the bug that when mesh AP is powered off during upgrade, Controller may fail to upgrade other APs, with a prompt message “Other APs are upgrading”.

 

Notes:

1. To use Omada Controller 3.2.X new features, you need to upgrade your EAP's firmware to the corresponding version.

2. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

3. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.X or earlier version.
Published Date: 2019-11-08 Language: English File Size: 99.4MB
Operating System: Ubuntu 14.04/16.04/17.04/18.04/Debian 9.8

New Feature/Enhancement:

1. Add “Select Page” feature on voucher management page.

2. Change default status of “Terms of Service” on default portal page to uncheck.

3. Optimize the “Free Authentication Policy” to support URL with suffixes.

4. Change the default status of new added “Free Authentication Policy” to enable.

 

Bug Fixed:

1. Fixed the bug that when clients disconnect from the Facebook portal, the connection time and traffic usage of these clients may be zero in the log.

2. Fixed the bug that AP may disconnect from Omada Controller when it is upgrading the firmware.

3. Fixed the bug that in some cases, the channel configuration of 2.4G frequency may show up in 5G by mistake.

4. Fixed the bug that the configuration of SSID will not be issued correctly when changing the WLAN Group on the provisioning status.

 

Notes:

1. To use new features on Omada Controller 3.2.X, you need to upgrade your EAP's firmware to the corresponding version.

2. The Omada Controller program needs to use the system's netstat command. If the Linux system does not have net-tools installed (which contain the netstat command), the program may not be able to run normally.

3. Support 64-bit Linux operating system including Ubuntu 14.04/16.04/17.04/18.04/Debian 9.8

4. Built-in JRE 1.8 Java environment.

5. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

6. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.8.
Published Date: 2019-11-08 Language: English File Size: 123.35MB
Operating System: Ubuntu 14.04/16.04/17.04/18.04, CentOS 6.x/7.x and Fedora 20 or above, Debian 9.8.

New Feature/Enhancement:

1. Add “Select Page” feature on the management page of vouchers.

2. Change the default status of “Terms of Service” to uncheck.

3. Optimize the “Free Authentication Policy” to support URL with suffixes.

4. Change the default status of new added “Free Authentication Policy” to enable.

 

Bug Fixed:

1. Fixed the bug that when clients disconnect from the Facebook portal, the connection time and traffic usage of these clients may be zero in the log.

2. Fixed the bug that AP may disconnect from Omada Controller when it is upgrading the firmware.

3. Fixed the bug that in some cases, the channel configuration of 2.4G frequency may show up in 5G by mistake.

4. Fixed the bug that the configuration of SSID will not be issued correctly when changing the WLAN Group on the provisioning status.

 

 

Notes:

1. To use new features on Omada Controller 3.2.x, you need to upgrade your EAP's firmware to the corresponding version.

2. The Omada Controller program needs to use the system's netstat command. If the Linux system does not have net-tools installed (which contain the netstat command), the program may not be able to run normally.

3. Support 64-bit Linux operating system including Ubuntu 14.04/16.04/17.04/18.04, CentOS 6.x/7.x and Fedora 20 or above, Debian 9.8.

4. Built-in JRE 1.8 Java environment.

5. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

6. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.8.

7. When upgrading from Controller 2.5.3 Linux to this version via install.sh, you need to uninstall old version of Controller first.
Published Date: 2019-11-08 Language: English File Size: 120.52MB
Operating System: Windows 7/8/10/Server

New Feature/Enhancement:

1. Add “Select Page” feature on the voucher management page.

2. Change the default status of “Terms of Service” on default portal page to uncheck.

3. Optimize the “Free Authentication Policy” to support URL with suffixes.

4. Change the default status of new added “Free Authentication Policy” to enable.

 

Bug Fixed:

1. Fixed the bug that when clients disconnect from the Facebook portal, the connection time and traffic usage of these clients may be zero in the log.

2. Fixed the bug that AP may disconnect from Omada Controller when it is upgrading the firmware.

3. Fixed the bug that in some cases, the channel configuration of 2.4G frequency may show up in 5G by mistake.

4. Fixed the bug that the configuration of SSID will not be issued correctly when changing the WLAN Group on the provisioning status.

 

Notes:

1. To use Omada Controller 3.2.x new features, you need to upgrade your EAP's firmware to the corresponding version.

2. Once upgraded to this version of Omada Controller, you will NOT be able to downgrade to an earlier version.

3. Portal configuration will be lost after upgrading to Omada Controller 3.2.X from 2.4.X or earlier version.

4. You are recommended to create a backup before upgrading, or you will not be permitted to install this version of Omada Controller.
Published Date: 2019-11-08 Language: English File Size: 124.43MB
Operating System: Windows 7/8/10/Server

New Feature/Enhancement:

1. Add “Select Page” feature on the voucher management page.

2. Change the default status of “Terms of Service” on default portal page to uncheck.

3. Optimize the “Free Authentication Policy” to support URL with suffixes.

4. Change the default status of new added “Free Authentication Policy” to enable.

 

Bug Fixed:

1. Fixed the bug that when clients disconnect from the Facebook portal, the connection time and traffic usage of these clients may be zero in the log.

2. Fixed the bug that AP may disconnect from Omada Controller when it is upgrading the firmware.

3. Fixed the bug that in some cases, the channel configuration of 2.4G frequency may show up in 5G by mistake.

4. Fixed the bug that the configuration of SSID will not be issued correctly when changing the WLAN Group on the provisioning status.

 

Notes:

1. To use Omada Controller 3.2.x new features, you need to upgrade your EAP's firmware to the corresponding version.

2. Once upgraded to this version of Omada Controller, you will NOT be able to downgrade to an earlier version.

3. Portal configuration will be lost after upgrading to Omada Controller 3.2.X from 2.4.X or earlier version.

4. You are recommended to create a backup before upgrading, or you will not be permitted to install this version of Omada Controller.
Published Date: 2019-07-26 Language: English File Size: 99.23MB
Operating System: Ubuntu 14.04/16.04/17.04/18.04/Debian 9.8

New Feature/Enhancement:

1. Optimize the performance of Controller to manage up to 1500 EAPs.

2. Optimize the interactive process between EAP and Controller to decrease the processing time.

3. Limit the entry number of client/client history/guest to 1.2 million/1.2 million /6 million.

4. Optimize display page of map and log when there are a lot of entries.

 

Bug Fixed:

1. Fixed the bug that CPU and memory may be highly used when Fast Roaming is enabled.

2. Fixed the bug that Omada Controller reports timeout error when adopting multiple EAPs simultaneously.

3. Fixed the bug that Controller will print all Voucher codes even only some of the codes are selected.

 

Notes:

1. To use new features on Omada Controller 3.2.X, you need to upgrade your EAP's firmware to the corresponding version.

2. The Omada Controller program needs to use the system's netstat command. If the Linux system does not have net-tools installed (which contain the netstat command), the program may not be able to run normally.

3. Support 64-bit Linux operating system including Ubuntu 14.04/16.04/17.04/18.04/Debian 9.8

4. Built-in JRE 1.8 Java environment.

5. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

6. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.8.

 
Published Date: 2019-07-26 Language: English File Size: 123.15MB
Operating System: Ubuntu 14.04/16.04/17.04/18.04, CentOS 6.x/7.x and Fedora 20 or above, Debian 9.8.

New Feature/Enhancement:

1. Optimize the performance of Controller to manage up to 1500 EAPs.

2. Optimize the interactive process between EAP and Controller to decrease the processing time.

3. Limit the entry number of client/client history/guest to 1.2 million/1.2 million /6 million.

4. Optimize display page of map and log when there are a lot of entries.

 

Bug Fixed:

1. Fixed the bug that CPU and memory may be highly used when Fast Roaming is enabled.

2. Fixed the bug that Omada Controller reports timeout error when adopting multiple EAPs simultaneously.

3. Fixed the bug that Controller will print all Voucher codes even only some of the codes are selected.

 

Notes:

1. To use new features on Omada Controller 3.2.x, you need to upgrade your EAP's firmware to the corresponding version.

2. The Omada Controller program needs to use the system's netstat command. If the Linux system does not have net-tools installed (which contain the netstat command), the program may not be able to run normally.

3. Support 64-bit Linux operating system including Ubuntu 14.04/16.04/17.04/18.04, CentOS 6.x/7.x and Fedora 20 or above, Debian 9.8.

4. Built-in JRE 1.8 Java environment.

5. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

6. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.8.

7. When upgrading from Controller 2.5.3 Linux to this version via install.sh, you need to uninstall old version of Controller first.
Published Date: 2019-07-04 Language: English File Size: 120.29MB
Operating System: Windows 7/8/10/Server

New Feature/Enhancement:

1. Optimize the performance of Controller to manage up to 1500 EAPs.

2. Optimize the interactive process between EAP and Controller to decrease the process time.

3. Limit the entry number of client/client history/guest to 1.2 million/1.2 million /6 million.

4. Optimize display page of map and log when there are a lot of entries.

 

Bug Fixed:

1. Fixed the bug that CPU and memory may be highly used when Fast Roaming is enabled.

2. Fixed the bug that Omada Controller reports timeout error when adopting multiple EAPs simultaneously.

3. Fixed the bug that Controller will print all Voucher codes even only some of the codes are selected.

 

Notes:

1. To use Omada Controller 3.2.x new features, you need to upgrade your EAP's firmware to the corresponding version.

2. Once upgraded to this version of Omada Controller, you will NOT be able to downgrade to an earlier version.

3. Portal configuration will be lost after upgrading to Omada Controller 3.2.X from 2.4.X or earlier version.
Published Date: 2019-07-04 Language: English File Size: 124.2MB
Operating System: Windows 7/8/10/Server

New Feature/Enhancement:

1. Optimize the performance of Controller to manage up to 1500 EAPs.

2. Optimize the interactive process between EAP and Controller to decrease the process time.

3. Limit the entry number of client/client history/guest to 1.2 million/1.2 million /6 million.

4. Optimize display page of map and log when there are a lot of entries.

 

Bug Fixed:

1. Fixed the bug that CPU and memory may be highly used when Fast Roaming is enabled.

2. Fixed the bug that Omada Controller reports timeout error when adopting multiple EAPs simultaneously.

3. Fixed the bug that Controller will print all Voucher codes even only some of the codes are selected.

 

Notes:

1. To use Omada Controller 3.2.x new features, you need to upgrade your EAP's firmware to the corresponding version.

2. Once upgraded to this version of Omada Controller, you will NOT be able to downgrade to an earlier version.

3. Portal configuration will be lost after upgrading to Omada Controller 3.2.X from 2.4.X or earlier version.
Published Date: 2019-03-08 Language: English File Size: 127.5MB
Operating System: Windows 7/8/10/Server

New Feature/Enhancement:

1. Merge 2.4GHz and 5GHz SSID.

2. Add Guest Network function.

3. Optimize log field and content.

4. Add SSID Radius accounting to WPA-Enterprise security mode.

5. Optimize the site list which allows us to inquire the specific site based on the site name and add new entrance for the hotspot.

6. Add SSL encryption in Log Server, and Log setting/Mail Server can be only accessed by administrator account.

7. Add Layer-3 Accessibility in SSH.

8. Add Mesh settings to Backup and Restore file.

9. Add CHAP encryption and NAS ID in Radius portal authentication and the Radius Client role is transferred from EAP to Omada Controller.

10. Add SSID MAC Authentication to none security mode.

11. Add channel utilization function.

12. Add Full-Sector DFS function in Mesh network.

13. Channel limit is revised from private configuration to site settings.

14. Support inputting domain name in SMTP server.

 

Notes:

1. The log will be cleared when you upgrade the software from version 3.0.x to version 3.1.4.

2. Add push notification to Omada APP of version 2.1.4 or above when EAP is connected/disconnected from Omada Controller.

3. This version of Omada Controller is applied to Omada APP of version 2.1.4 or above.

4. When you upgrade your controller or backup files from lower version, the 2.4GHz and 5GHz SSID entries with the same name will be merged and it will inherit the parameters of the original 2.4GHz SSID.

5. If you use External Radius Server with External Web Portal in old version controller, pay attention that the API has been changed in this version, thus you have to modify your External Web Portal, refer to FAQ-2390 for more details.

6. The log generated by EAP will be managed and storaged by Controller if you manage EAPs by Omada Controller.

7. Channel utilization will take effect only with new firmware.

EAP Discovery Tool

The EAP Discovery Tool can help the EAP Controller to adopt the EAP in L3 Network, and you can also use the EAP Discovery Tool to find the EAP’s IP address.

Published Date: 2019-08-06 Language: English File Size: 25.85 MB
Operating System: WinXP/Vista/7/8/8.1/10/Server2008/Server2012/Mac OS X 10.7/10.8/10.9/10.10/10.11

Bug fixed:

1. Fixed the bug that the Discovery Utility may fail to find EAPs.

2. Fixed the bug that the Cancel button may overlap with the display box after managing APs.

 

Note:

1. This version of software can be used in both Windows and Mac operation system.

2. Double click the software or run the command “java –jar **.jar” to run the software on MacOS (**.jar is the name of this software).

3. To run this software, you need to install JRE 8.0 on your PC first.
Published Date: 2019-06-14 Language: English File Size: 23.54 MB
Operating System: WinXP/Vista/7/8/8.1/10/Server2008/Server2012/Mac OS X 10.7/10.8/10.9/10.10/10.11

Bug fixed:

1. Fixed the bug that when the Discovery Utility issues Controller_IP to EAPs which are in factory status, Controller cannot batch manage the EAPs.

2. Fixed the bug that sometimes the Discovery Utility cannot find all EAPs when running in MacOS.

Note:

1. This version of software can be used in both Windows and Mac operation system.

2. Double click the software or run the command “java –jar **.jar” to run the software on MacOS(**.jar is the name of this software).

3. To run this software, you need to install JRE 8.0 on your PC.
Published Date: 2018-07-24 Language: English File Size: 84.16 MB
Operating System: Mac OS X 10.7/10.8/10.9/10.10/10.11

New Feature/Enhancement:
1. Change name to "Omada Discovery Utility".
2. Update background picture during installation.
3. Limit the maximum length of controller hostname to 79.
 
Bug Fixed:
Fix the bug that searching in the search box will cause the software to hang.
 
Note:
Operating System: Mac OS X 10.7/10.8/10.9/10.10/10.11.

Feature Filter: All EAP AdoptionPortalManagementQuick StartConfigurationConfiguration Example

Q&A

Feature Configuration Guide

T2700G-28TQ License Download
License Model: T2700G-28TQ-L1000

Find your product MAC and Serial Number.
License Key:
Product Serial Number:
Product MAC:
Checking code:

Sign up for news & offersTP-Link takes your privacy seriously. For further details on TP-Link's privacy practices, see TP-Link's Privacy Policy.

Follow Us

About Us
Press
Where to Buy
Partners
Promotions
United Kingdom / English
Copyright © 2020 TP-Link Technologies Co., Ltd. All rights reserved.