Setup Video

  • How to manage TP-Link EAPs centrally via the Software Controller

    This video demonstrates how to manage TP-Link EAPs centrally via the Software Controller. The setup consists of three steps:
    • Install the Software
    • Configure Discovery Utility (If your EAPs and the Controller Host are on different subnets)
    • Configure Software Controller

    THIS VIDEO APPLIES TO:
    • All TP-Link EAP models (except EAP120 and EAP220)
    • Omada Software Controller
    • Mass EAPs (usually more than three)

    Więcej

  • How to set up a TP Link EAP via your mobile phone

    This video demonstrates how to set up a TP-Link EAP via your mobile phone. The setup consists of four steps:
    • Connect the EAP to the network
    • Download the Omada APP
    • Connect to the EAP's wireless network
    • Set up the EAP using the Omada APP

    THIS VIDEO APPLIES TO:
    • All TP-Link EAP models. (except EAP120 and EAP220)
    • A small number (1-3) of EAPs.

    Więcej

  • How to setup the OC200 via a web browser

    This video will demonstrate how to set up the OC200 via a web browser. The setup consists of six steps:
    • Connect the OC200 to your local network.
    • Get ready for setup.
    • Create a TP-Link ID.
    • Log into your TP-Link ID.
    • Add the OC200 to your TP-Link ID.
    • Follow the wizard to set up the OC200.

    THIS VIDEO APPLIES TO:
    • All TP-Link EAP models (except EAP120 and EAP220)
    • Omada Cloud Controller OC200
    • Mass EAPs (usually more than three)

    Więcej

  • How to setup the OC200 via your mobile phone

    This video will demonstrate how to set up the OC200 via your mobile phone. You need to use the Omada APP to complete the setup. The setup consists of six steps:
    • Connect the OC200 to your local network.
    • Get ready for setup.
    • Create a TP-Link ID.
    • Log into your TP-Link ID.
    • Add the OC200 to your TP-Link ID.
    • Follow the wizard to set up the OC200.
    THIS VIDEO APPLIES TO:
    • All TP-Link EAP models (except EAP120 and EAP220)
    • Omada Cloud Controller OC200
    • Mass EAPs (usually more than three)

    Więcej

  • How to manage TP-Link EAPs centrally from a remote place via a web browser

    You can manage TP-Link EAPs at any time from anywhere with the Cloud Access function of our Omada Controller Software. This video introduces both the application scenario and concrete steps you can follow. Don't hesitate to give it a try.
    THIS VIDEO APPLIES TO:
    • All TP-Link EAP models (except EAP120 and EAP220)
    • Omada Controller Software (version 3.0.2 or above)
    • Mass EAPs (usually more than three)

    Więcej

  • A Quick Overview of EAP Management Methods

    This video introduces how to choose the optimum method to manage TP-Link EAPs in your scenario.
    Here are 3 most common scenarios and their corresponding methods:
    • Manage 1 or 2 EAPs locally
    • Manage 3 or more EAPs locally
    • Manage 3 or more EAPs remotely
    When choosing the method, consider the following questions:
    1. Standalone Mode or Controller Mode?
    2. In Controller mode, what kind of controller will you use, an OC200 or a PC with Omada Software Controller?
    3. What kind of user interface will you use, a web browser or the Omada app?

    Więcej

  • How to Set up a TP-Link EAP via Web browser

    This video will demonstrate how to set up a TP-Link EAP via a web browser. The setup consists of three steps:
    1. Connect the EAP to the network
    2. Log into the EAP (via a wired/wireless connection)
    3. Change the default SSID
    This video is suitable for users with a small number (1-3) of EAPs .

    Więcej

FAQ

Firmware

Aktualizacja oprogramowania pozwala na rozwiązanie problemów ze starszą wersją oprogramowania oraz na dodanie nowych funkcji routera.

Aktualizacja

WAŻNE: Aby zapobiec problemom podczas aktualizacji, zapoznaj się z poniższymi punktami

  • Upewnij się, że oprogramowanie jest przeznaczone dla twojej wersji sprzętowej routera. Zainstalowanie oprogramowania dla nieprawidłowej wersji może uszkodzić urządzenie i spowodować utratę gwarancji.( V1.x=V1)
  • NIE zalecamy używania oprogramowania przeznaczonego dla innego regionu niż ten, w którym się znajdujesz. Możesz wybrać swój region tutaj.
  • NIE odłączaj urządzenia od prądu podczas trwania aktualizacji. Może to spowodować trwałe uszkodzenia.
  • NIE przeprowadzaj aktualizacji za pomocą połączenia bezprzewodowego jeżeli nie jest to konieczne.
  • Zalecamy rozłączenie połączenia z Internetem przez przeprowadzeniem aktualizacji.
  • Rozpakuj pobrany plik za pomocą programu do dekompresji, takiego jak np. 7Zip lub WinRAR.

 

EAP225-Wall(EU)_V2_1.4.0 Build 20191213
Data publikacji: 2020-03-02 Język: Angielski Rozmiar pliku: 7.60 MB

Recommended Controller Software Version: Omada Controller v3.2.6 or above

 

New Feature/Enhancement:

1. Change the mechanism that the IP configuration in Standalone mode will be retained after the EAP is adopted by the Controller.

2. Add anti-brute force cracking mechanism that you cannot login to the EAP via SSH or webserver in two hours if you fail to login up to 30 times in half an hour.

3. Optimize NTP server to support domain name.

4. Change the “Term of Service” of portal settings page in standalone mode as unchecked by default.

5. Optimize the UI of SSID and Free Authentication Policy in Standalone mode.

6. Optimize the DNS resolution process of EAP to avoid parsing wrong IP.

7. Reduce the time interval to 5s and limit the size to 2k bytes of the More Client Detail Log in Log Settings.

 

Bug Fixed:

1. Fixed the bug that the Max TX rate of 5G band in Standalone mode may display wrong value.

2. Fixed the bug that the EAP may hang after clicking save in Wireless VLAN page in Standalone mode.

3. Fixed the bug that the EAP may hang if scanning rogue AP in high frequency.

4. Fixed the bug that when adding an SSID with no password and change the encryption mode to WPA on Omada APP, the clients can still connect to the SSID without password.

5. Fixed the bug that External Radius Server portal page may not pop up in some clients.

 

Notes:

1. For EAP225-Wall v2 only.

2. Your device's configuration won't be lost after upgrading.

3. This version of firmware is applied to Omada APP of version 2.1.X or above.

4. You cannot downgrade if you upgrade from the firmware released in 2018 or earlier to this version directly.

 

EAP225-Wall(EU)_V2_1.3.1 Build 20191022
Data publikacji: 2019-12-11 Język: Angielski Rozmiar pliku: 7.59 MB

Recommended Controller Software Version: Omada Controller v3.2.x or above

Bug Fixed:
1. Fixed the bug that EAP may disconnect from Omada Controller.
2. Fixed the bug that the time zone displayed on the web UI of Standalone mode may be different from the connected PC.

Notes:
1. For EAP225-Wall v2 only.
2. Your device's configuration won't be lost after upgrading.
3. This version of firmware is applied to Omada APP of version 2.1.X or above.

4. You cannot downgrade if you upgrade from 2018 or older firmware to this version directly.

EAP225-Wall(EU)_V2_1.3.0 Build 20190722
Data publikacji: 2019-11-08 Język: Angielski Rozmiar pliku: 7.59 MB

Recommended Controller Software Version: Omada Controller v3.2.x or above

 

New Feature/Enhancement:

1. Change the OpenSSL version to 1.0.2q.

2. Optimize UI, including character optimization and display error correction.

 

Bug Fixed:

1. Fixed the bug that client devices can pass the portal authentication after disconnected from the Controller.

2. Fixed the bug that untag packets can be transferred to SSIDs with different VLANs.

5. Fixed the bug that some EAPs may disconnect from the Omada Controller in large scale network.

6. Fixed the bug that the management page may not be accessed after EAP is disconnected from the Controller.

7. Fixed the bug that when APs are disconnected from Controller, the rate limit configuration will be not issued to these APs after they are back to connected again.

8. Fixed the bug that when the time of EAP is synchronized with PC, it will be the same as PC's time not considering different time zones.

9. Fixed the bug that packets with VLAN tag can be forwarded to the SSID without wireless VLAN setting.

 

Notes:

1. For EAP225-Wall v2 only.

2. Your device's configuration won't be lost after upgrading.

3. This version of firmware is applied to Omada APP of version 2.1.X or above.

Korzystanie z firmware'u innej firmy

W przypadku niektórych modeli produktów TP-LINK istnieje możliwość zastąpienia firmware'u udostępnionego przez TP-LINK firmwarem oferowanym przez inną firmę. Jednakże, firma TP-LINK nie jest zobowiązana do wykonywania żadnych prac konserwacyjnych i nie oferuje wsparcia technicznego dla takich produktów. Nie gwarantuje także stabilności oraz poprawności działania firmware'u innej firmy. Uszkodzenie produktu, spowodowane korzystaniem z firmware'u innej firmy, powoduje utratę jego gwarancji.   

Centrum GPL

Produkty TP-LINK korzystają częściowo z oprogramowania stworzonego przez strony trzecie, w tym z kodu źródłowego oprogramowania zgodnego z licencją GNU General Public Licence (“GPL“), w wersji 1/wersji 2/wersji 3 lub licencji GNU Lesser General Public License ("LGPL"). Aby korzystać z oprogramowania, musisz się zgodzić się na warunki użytkowania produktów na licencji GPL.

Aby spełnić warunki licencji GPL, firma TP-LINK, jeżeli to konieczne, wysyła pocztą kody źrółowe GPL dla konkretnych oprogramowań na płycie CD do odczytu elektronicznego lub drogą mailową. Więcej informacji można uzyskać dla określonych produktów lub oprogramowań. Poprzez Centrum GPL firma TP-LINK zapewnia możliwość bezpłatnego pobierania kodów źródłowych oprogramowań zgodnych z licencją GPL oraz stosowanych w produktach TP-LINK.

Warunki licencji GPL znajdziesz, wydrukujesz i pobierzesz tutaj.

Dostępne programy rozprowadzane są BEZ GWARANCJI; nie obejmuje ich także gwarancja PRZYDATNOŚCI HANDLOWEJ oraz PRZYDATNOŚCI DO OKREŚLONEGO CELU. Więcej informacji dostępnych jest na stronie GNU GPL.

Controller Software

EAP Controller jest używany do zarządzania wieloma urządzeniami EAP.

Data publikacji: 2020-01-21 Język: Angielski Rozmiar pliku: 120.53MB
System operacyjny: Windows 7/8/10/Server

New Feature/Enhancement:

1. Expand the number of Omada Controller’s User Account to 500.  

2. Optimize the External Portal Server to support URL with parameters.

 

Notes:

1. To use Omada Controller 3.2.X new features, you need to upgrade your EAP's firmware to the corresponding version.

2. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

3. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.X or earlier version.

 

Data publikacji: 2020-01-21 Język: Angielski Rozmiar pliku: 124.45MB
System operacyjny: Windows 7/8/10/Server

New Feature/Enhancement:

1. Expand the number of Omada Controller’s User Account to 500.  

2. Optimize the External Portal Server to support URL with parameters.

 

Notes:

1. To use Omada Controller 3.2.X new features, you need to upgrade your EAP's firmware to the corresponding version.

2. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

3. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.X or earlier version.

Data publikacji: 2020-01-16 Język: Angielski Rozmiar pliku: 123.35MB
System operacyjny: Ubuntu 14.04/16.04/17.04/18.04, CentOS 6.x/7.x and Fedora 20 or above, Debian 9.8.

New Feature/Enhancement:

1. Change the mechanism that when adopting an EAP, the Controller will retain the IP configuration of EAP in Standalone mode.

2. Change the mechanism that multiple Omada Controllers can run on the same subnet.

3. Add the button of “Start Omada Controller after installation” and check it by default.

4. Extend the Max Associated Clients in Load Balance to 255.

5. Optimize the UI of Channel Utilization.

6. Optimize the authentication page of portal.

7. Optimize the UI of the portal that you cannot click Apply when you are uploading a photo.

8. Optimize the External Portal Server to support URL with parameters.

 

Bug Fixed:

1. Fixed the bug that the page of MAC filter may not display all groups when there are more than 5 groups.

2. Fixed the bug that after deleting a site, the Voucher code and Local user of this site still exist.

3. Fixed the bug that the site configuration will fail to restore when the imported site contains same Voucher code as the current Controller.

4. Fixed the bug that when mesh AP is powered off during upgrade, Controller may fail to upgrade other APs, with a prompt message “Other APs are upgrading”.

 

Notes:

1. To use new features on Omada Controller 3.2.x, you need to upgrade your EAP's firmware to the corresponding version.

2. The Omada Controller program needs to use the system's netstat command. If the Linux system does not have net-tools installed (which contain the netstat command), the program may not be able to run normally.

3. Support 64-bit Linux operating system including Ubuntu 14.04/16.04/17.04/18.04, CentOS 6.x/7.x and Fedora 20 or above, Debian 9.8.

4. Built-in JRE 1.8 Java environment.

5. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

6. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.8.

7. When upgrading from Controller 2.5.3 Linux to this version via install.sh, you need to uninstall old version of Controller first.

 

Data publikacji: 2020-01-16 Język: Angielski Rozmiar pliku: 99.4MB
System operacyjny: Ubuntu 14.04/16.04/17.04/18.04/Debian 9.8

New Feature/Enhancement:

1. Change the mechanism that when adopting an EAP, the Controller will retain the IP configuration of EAP in Standalone mode.

2. Change the mechanism that multiple Omada Controllers can run on the same subnet.

3. Add the button of “Start Omada Controller after installation” and check it by default.

4. Extend the Max Associated Clients in Load Balance to 255.

5. Optimize the UI of Channel Utilization.

6. Optimize the authentication page of portal.

7. Optimize the UI of the portal that you cannot click Apply when you are uploading a photo.

8. Optimize the External Portal Server to support URL with parameters.

 

Bug Fixed:

1. Fixed the bug that the page of MAC filter may not display all groups when there are more than 5 groups.

2. Fixed the bug that after deleting a site, the Voucher code and Local user of this site still exist.

3. Fixed the bug that the site configuration will fail to restore when the imported site contains same Voucher code as the current Controller.

4. Fixed the bug that when mesh AP is powered off during upgrade, Controller may fail to upgrade other APs, with a prompt message “Other APs are upgrading”.

 

Notes:

1. To use new features on Omada Controller 3.2.X, you need to upgrade your EAP's firmware to the corresponding version.

2. The Omada Controller program needs to use the system's netstat command. If the Linux system does not have net-tools installed (which contain the netstat command), the program may not be able to run normally.

3. Support 64-bit Linux operating system including Ubuntu 14.04/16.04/17.04/18.04/Debian 9.8

4. Built-in JRE 1.8 Java environment.

5. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

6. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.8.

Data publikacji: 2020-01-09 Język: Angielski Rozmiar pliku: 120.53MB
System operacyjny: Windows 7/8/10/Server

New Feature/Enhancement:

1. Change the mechanism that when adopting an EAP, the Controller will retain the IP configuration of EAP in Standalone mode.

2. Change the mechanism that multiple Omada Controllers can run on the same subnet.

3. Add the button of “Start Omada Controller after installation” and check it by default.

4. Extend the Max Associated Clients in Load Balance to 255.

5. Optimize the UI of Channel Utilization.

6. Optimize the authentication page of portal.

7. Optimize the UI of the portal that you cannot click Apply when you are uploading a photo.

 

Bug Fixed:

1. Fixed the bug that the page of MAC filter may not display all groups when there are more than 5 groups.

2. Fixed the bug that after deleting a site, the Voucher code and Local user of this site still exist.

3. Fixed the bug that the site configuration will fail to restore when the imported site contains same Voucher code as the current Controller.

4. Fixed the bug that when mesh AP is powered off during upgrade, Controller may fail to upgrade other APs, with a prompt message “Other APs are upgrading”.

 

Notes:

1. To use Omada Controller 3.2.X new features, you need to upgrade your EAP's firmware to the corresponding version.

2. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

3. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.X or earlier version.

Data publikacji: 2020-01-09 Język: Angielski Rozmiar pliku: 124.44MB
System operacyjny: Windows 7/8/10/Server

New Feature/Enhancement:

1. Change the mechanism that when adopting an EAP, the Controller will retain the IP configuration of EAP in Standalone mode.

2. Change the mechanism that multiple Omada Controllers can run on the same subnet.

3. Add the button of “Start Omada Controller after installation” and check it by default.

4. Extend the Max Associated Clients in Load Balance to 255.

5. Optimize the UI of Channel Utilization.

6. Optimize the authentication page of portal.

7. Optimize the UI of the portal that you cannot click Apply when you are uploading a photo.

 

Bug Fixed:

1. Fixed the bug that the page of MAC filter may not display all groups when there are more than 5 groups.

2. Fixed the bug that after deleting a site, the Voucher code and Local user of this site still exist.

3. Fixed the bug that the site configuration will fail to restore when the imported site contains same Voucher code as the current Controller.

4. Fixed the bug that when mesh AP is powered off during upgrade, Controller may fail to upgrade other APs, with a prompt message “Other APs are upgrading”.

 

Notes:

1. To use Omada Controller 3.2.X new features, you need to upgrade your EAP's firmware to the corresponding version.

2. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

3. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.X or earlier version.

Data publikacji: 2019-11-08 Język: Angielski Rozmiar pliku: 99.4MB
System operacyjny: Ubuntu 14.04/16.04/17.04/18.04/Debian 9.8

New Feature/Enhancement:

1. Add “Select Page” feature on voucher management page.

2. Change default status of “Terms of Service” on default portal page to uncheck.

3. Optimize the “Free Authentication Policy” to support URL with suffixes.

4. Change the default status of new added “Free Authentication Policy” to enable.

 

Bug Fixed:

1. Fixed the bug that when clients disconnect from the Facebook portal, the connection time and traffic usage of these clients may be zero in the log.

2. Fixed the bug that AP may disconnect from Omada Controller when it is upgrading the firmware.

3. Fixed the bug that in some cases, the channel configuration of 2.4G frequency may show up in 5G by mistake.

4. Fixed the bug that the configuration of SSID will not be issued correctly when changing the WLAN Group on the provisioning status.

 

Notes:

1. To use new features on Omada Controller 3.2.X, you need to upgrade your EAP's firmware to the corresponding version.

2. The Omada Controller program needs to use the system's netstat command. If the Linux system does not have net-tools installed (which contain the netstat command), the program may not be able to run normally.

3. Support 64-bit Linux operating system including Ubuntu 14.04/16.04/17.04/18.04/Debian 9.8

4. Built-in JRE 1.8 Java environment.

5. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

6. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.8.

Data publikacji: 2019-11-08 Język: Angielski Rozmiar pliku: 123.35MB
System operacyjny: Ubuntu 14.04/16.04/17.04/18.04, CentOS 6.x/7.x and Fedora 20 or above, Debian 9.8.

New Feature/Enhancement:

1. Add “Select Page” feature on the management page of vouchers.

2. Change the default status of “Terms of Service” to uncheck.

3. Optimize the “Free Authentication Policy” to support URL with suffixes.

4. Change the default status of new added “Free Authentication Policy” to enable.

 

Bug Fixed:

1. Fixed the bug that when clients disconnect from the Facebook portal, the connection time and traffic usage of these clients may be zero in the log.

2. Fixed the bug that AP may disconnect from Omada Controller when it is upgrading the firmware.

3. Fixed the bug that in some cases, the channel configuration of 2.4G frequency may show up in 5G by mistake.

4. Fixed the bug that the configuration of SSID will not be issued correctly when changing the WLAN Group on the provisioning status.

 

 

Notes:

1. To use new features on Omada Controller 3.2.x, you need to upgrade your EAP's firmware to the corresponding version.

2. The Omada Controller program needs to use the system's netstat command. If the Linux system does not have net-tools installed (which contain the netstat command), the program may not be able to run normally.

3. Support 64-bit Linux operating system including Ubuntu 14.04/16.04/17.04/18.04, CentOS 6.x/7.x and Fedora 20 or above, Debian 9.8.

4. Built-in JRE 1.8 Java environment.

5. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

6. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.8.

7. When upgrading from Controller 2.5.3 Linux to this version via install.sh, you need to uninstall old version of Controller first.

Data publikacji: 2019-11-08 Język: Angielski Rozmiar pliku: 120.52MB
System operacyjny: Windows 7/8/10/Server

New Feature/Enhancement:

1. Add “Select Page” feature on the voucher management page.

2. Change the default status of “Terms of Service” on default portal page to uncheck.

3. Optimize the “Free Authentication Policy” to support URL with suffixes.

4. Change the default status of new added “Free Authentication Policy” to enable.

 

Bug Fixed:

1. Fixed the bug that when clients disconnect from the Facebook portal, the connection time and traffic usage of these clients may be zero in the log.

2. Fixed the bug that AP may disconnect from Omada Controller when it is upgrading the firmware.

3. Fixed the bug that in some cases, the channel configuration of 2.4G frequency may show up in 5G by mistake.

4. Fixed the bug that the configuration of SSID will not be issued correctly when changing the WLAN Group on the provisioning status.

 

Notes:

1. To use Omada Controller 3.2.x new features, you need to upgrade your EAP's firmware to the corresponding version.

2. Once upgraded to this version of Omada Controller, you will NOT be able to downgrade to an earlier version.

3. Portal configuration will be lost after upgrading to Omada Controller 3.2.X from 2.4.X or earlier version.

4. You are recommended to create a backup before upgrading, or you will not be permitted to install this version of Omada Controller.

Data publikacji: 2019-11-08 Język: Angielski Rozmiar pliku: 124.43MB
System operacyjny: Windows 7/8/10/Server

New Feature/Enhancement:

1. Add “Select Page” feature on the voucher management page.

2. Change the default status of “Terms of Service” on default portal page to uncheck.

3. Optimize the “Free Authentication Policy” to support URL with suffixes.

4. Change the default status of new added “Free Authentication Policy” to enable.

 

Bug Fixed:

1. Fixed the bug that when clients disconnect from the Facebook portal, the connection time and traffic usage of these clients may be zero in the log.

2. Fixed the bug that AP may disconnect from Omada Controller when it is upgrading the firmware.

3. Fixed the bug that in some cases, the channel configuration of 2.4G frequency may show up in 5G by mistake.

4. Fixed the bug that the configuration of SSID will not be issued correctly when changing the WLAN Group on the provisioning status.

 

Notes:

1. To use Omada Controller 3.2.x new features, you need to upgrade your EAP's firmware to the corresponding version.

2. Once upgraded to this version of Omada Controller, you will NOT be able to downgrade to an earlier version.

3. Portal configuration will be lost after upgrading to Omada Controller 3.2.X from 2.4.X or earlier version.

4. You are recommended to create a backup before upgrading, or you will not be permitted to install this version of Omada Controller.

Data publikacji: 2019-07-26 Język: Angielski Rozmiar pliku: 99.23MB
System operacyjny: Ubuntu 14.04/16.04/17.04/18.04/Debian 9.8

New Feature/Enhancement:

1. Optimize the performance of Controller to manage up to 1500 EAPs.

2. Optimize the interactive process between EAP and Controller to decrease the processing time.

3. Limit the entry number of client/client history/guest to 1.2 million/1.2 million /6 million.

4. Optimize display page of map and log when there are a lot of entries.

 

Bug Fixed:

1. Fixed the bug that CPU and memory may be highly used when Fast Roaming is enabled.

2. Fixed the bug that Omada Controller reports timeout error when adopting multiple EAPs simultaneously.

3. Fixed the bug that Controller will print all Voucher codes even only some of the codes are selected.

 

Notes:

1. To use new features on Omada Controller 3.2.X, you need to upgrade your EAP's firmware to the corresponding version.

2. The Omada Controller program needs to use the system's netstat command. If the Linux system does not have net-tools installed (which contain the netstat command), the program may not be able to run normally.

3. Support 64-bit Linux operating system including Ubuntu 14.04/16.04/17.04/18.04/Debian 9.8

4. Built-in JRE 1.8 Java environment.

5. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

6. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.8.

 

Data publikacji: 2019-07-26 Język: Angielski Rozmiar pliku: 123.15MB
System operacyjny: Ubuntu 14.04/16.04/17.04/18.04, CentOS 6.x/7.x and Fedora 20 or above, Debian 9.8.

New Feature/Enhancement:

1. Optimize the performance of Controller to manage up to 1500 EAPs.

2. Optimize the interactive process between EAP and Controller to decrease the processing time.

3. Limit the entry number of client/client history/guest to 1.2 million/1.2 million /6 million.

4. Optimize display page of map and log when there are a lot of entries.

 

Bug Fixed:

1. Fixed the bug that CPU and memory may be highly used when Fast Roaming is enabled.

2. Fixed the bug that Omada Controller reports timeout error when adopting multiple EAPs simultaneously.

3. Fixed the bug that Controller will print all Voucher codes even only some of the codes are selected.

 

Notes:

1. To use new features on Omada Controller 3.2.x, you need to upgrade your EAP's firmware to the corresponding version.

2. The Omada Controller program needs to use the system's netstat command. If the Linux system does not have net-tools installed (which contain the netstat command), the program may not be able to run normally.

3. Support 64-bit Linux operating system including Ubuntu 14.04/16.04/17.04/18.04, CentOS 6.x/7.x and Fedora 20 or above, Debian 9.8.

4. Built-in JRE 1.8 Java environment.

5. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

6. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.8.

7. When upgrading from Controller 2.5.3 Linux to this version via install.sh, you need to uninstall old version of Controller first.

Data publikacji: 2019-07-04 Język: Angielski Rozmiar pliku: 120.29MB
System operacyjny: Windows 7/8/10/Server

New Feature/Enhancement:

1. Optimize the performance of Controller to manage up to 1500 EAPs.

2. Optimize the interactive process between EAP and Controller to decrease the process time.

3. Limit the entry number of client/client history/guest to 1.2 million/1.2 million /6 million.

4. Optimize display page of map and log when there are a lot of entries.

 

Bug Fixed:

1. Fixed the bug that CPU and memory may be highly used when Fast Roaming is enabled.

2. Fixed the bug that Omada Controller reports timeout error when adopting multiple EAPs simultaneously.

3. Fixed the bug that Controller will print all Voucher codes even only some of the codes are selected.

 

Notes:

1. To use Omada Controller 3.2.x new features, you need to upgrade your EAP's firmware to the corresponding version.

2. Once upgraded to this version of Omada Controller, you will NOT be able to downgrade to an earlier version.

3. Portal configuration will be lost after upgrading to Omada Controller 3.2.X from 2.4.X or earlier version.

Data publikacji: 2019-07-04 Język: Angielski Rozmiar pliku: 124.2MB
System operacyjny: Windows 7/8/10/Server

New Feature/Enhancement:

1. Optimize the performance of Controller to manage up to 1500 EAPs.

2. Optimize the interactive process between EAP and Controller to decrease the process time.

3. Limit the entry number of client/client history/guest to 1.2 million/1.2 million /6 million.

4. Optimize display page of map and log when there are a lot of entries.

 

Bug Fixed:

1. Fixed the bug that CPU and memory may be highly used when Fast Roaming is enabled.

2. Fixed the bug that Omada Controller reports timeout error when adopting multiple EAPs simultaneously.

3. Fixed the bug that Controller will print all Voucher codes even only some of the codes are selected.

 

Notes:

1. To use Omada Controller 3.2.x new features, you need to upgrade your EAP's firmware to the corresponding version.

2. Once upgraded to this version of Omada Controller, you will NOT be able to downgrade to an earlier version.

3. Portal configuration will be lost after upgrading to Omada Controller 3.2.X from 2.4.X or earlier version.

Data publikacji: 2019-03-08 Język: Angielski Rozmiar pliku: 123.6MB
System operacyjny: Windows 7/8/10/Server

New Feature/Enhancement:

1. Merge 2.4GHz and 5GHz SSID.

2. Add Guest Network function.

3. Optimize log field and content.

4. Add SSID Radius accounting to WPA-Enterprise security mode.

5. Optimize the site list which allows us to inquire the specific site based on the site name and add new entrance for the hotspot.

6. Add SSL encryption in Log Server, and Log setting/Mail Server can be only accessed by administrator account.

7. Add Layer-3 Accessibility in SSH.

8. Add Mesh settings to Backup and Restore file.

9. Add CHAP encryption and NAS ID in Radius portal authentication and the Radius Client role is transferred from EAP to Omada Controller.

10. Add SSID MAC Authentication to none security mode.

11. Add channel utilization function.

12. Add Full-Sector DFS function in Mesh network.

13. Channel limit is revised from private configuration to site settings.

14. Support inputting domain name in SMTP server.

 

Notes:

1. The log will be cleared when you upgrade the software from version 3.0.x to version 3.1.4.

2. Add push notification to Omada APP of version 2.1.4 or above when EAP is connected/disconnected from Omada Controller.

3. This version of Omada Controller is applied to Omada APP of version 2.1.4 or above.

4. When you upgrade your controller or backup files from lower version, the 2.4GHz and 5GHz SSID entries with the same name will be merged and it will inherit the parameters of the original 2.4GHz SSID.

5. If you use External Radius Server with External Web Portal in old version controller, pay attention that the API has been changed in this version, thus you have to modify your External Web Portal, refer to FAQ-2390 for more details.

6. The log generated by EAP will be managed and storaged by Controller if you manage EAPs by Omada Controller.

7. Channel utilization will take effect only with new firmware.

Data publikacji: 2019-03-08 Język: Angielski Rozmiar pliku: 127.5MB
System operacyjny: Windows 7/8/10/Server

New Feature/Enhancement:

1. Merge 2.4GHz and 5GHz SSID.

2. Add Guest Network function.

3. Optimize log field and content.

4. Add SSID Radius accounting to WPA-Enterprise security mode.

5. Optimize the site list which allows us to inquire the specific site based on the site name and add new entrance for the hotspot.

6. Add SSL encryption in Log Server, and Log setting/Mail Server can be only accessed by administrator account.

7. Add Layer-3 Accessibility in SSH.

8. Add Mesh settings to Backup and Restore file.

9. Add CHAP encryption and NAS ID in Radius portal authentication and the Radius Client role is transferred from EAP to Omada Controller.

10. Add SSID MAC Authentication to none security mode.

11. Add channel utilization function.

12. Add Full-Sector DFS function in Mesh network.

13. Channel limit is revised from private configuration to site settings.

14. Support inputting domain name in SMTP server.

 

Notes:

1. The log will be cleared when you upgrade the software from version 3.0.x to version 3.1.4.

2. Add push notification to Omada APP of version 2.1.4 or above when EAP is connected/disconnected from Omada Controller.

3. This version of Omada Controller is applied to Omada APP of version 2.1.4 or above.

4. When you upgrade your controller or backup files from lower version, the 2.4GHz and 5GHz SSID entries with the same name will be merged and it will inherit the parameters of the original 2.4GHz SSID.

5. If you use External Radius Server with External Web Portal in old version controller, pay attention that the API has been changed in this version, thus you have to modify your External Web Portal, refer to FAQ-2390 for more details.

6. The log generated by EAP will be managed and storaged by Controller if you manage EAPs by Omada Controller.

7. Channel utilization will take effect only with new firmware.

EAP Discovery Tool

EAP Discovery Tool pomaga zaadoptować urządzenia EAP kontrolerowi EAP w sieci L3. Możesz również użyć programu EAP Discovery Tool do sprawdzenia adresu IP urządzenia  EAP.

Data publikacji: 2018-07-24 Język: Angielski Rozmiar pliku: 84.16 MB
System operacyjny: Mac OS X 10.7/10.8/10.9/10.10/10.11

New Feature/Enhancement:
1. Change name to "Omada Discovery Utility".
2. Update background picture during installation.
3. Limit the maximum length of controller hostname to 79.
 
Bug Fixed:
Fix the bug that searching in the search box will cause the software to hang.
 
Note:
Operating System: Mac OS X 10.7/10.8/10.9/10.10/10.11.

Data publikacji: 2018-01-05 Język: Angielski Rozmiar pliku: 3.39MB
System operacyjny: WinXP/Vista/7/8/8.1/10/Server2008/Server2012

Apps

Omada APP

TP-Link Omada lets you configure settings, monitor network status and manage clients, all from the convenience of a smart phone or tablet. Learn more about Compatible Devices.

Note: To use Omada, please update your EAP's firmware to the latest version.

T2700G-28TQ License Download
License Model: T2700G-28TQ-L1000

Find your product MAC and Serial Number.
License Key:
Product Serial Number:
Product MAC:
Checking code:

NewsletterTP-Link poważnie traktuje twoją prywatność. Więcej szczegółów znajdziesz na stronie Informacja o przetwarzaniu danych osobowych.