4G LTE Router Setup Guide

Applicable Models:

Archer MR500 Ver: 2.0

Archer MR550 Ver: 2.0

Archer MR600 Ver: 5.20

Welcome! Let’s get your router up and running together.

This guide makes setup simple for everyone, covering helpful accessibility resources, what’s in the box, how it looks, and where to begin.

Our Tether app and web management page also offer accessibility features, such as increasing page contrast, switching to landscape mode and increasing font size. You can enable them during router setup for an easier and more enjoyable experience! For more accessibility guidance, refer to Accessibility Support.

Note: For some models, Accessibility features will be supported by subsequent firmware upgrades.

Now, ready to explore your router and get connected?

Step 1. Learn About Your Router

This section introduces the router’s package contents and appearance, including its ports, buttons, and product label.

1. Unbox Your Router

Your package includes: a router, a power adapter, an Ethernet cable, and installation guides.

Power Adapter: A block-shaped charger with a cord. Plug it into the router’s power slot to power on the router.

Ethernet Cable: A thick, smooth cord with a slightly stiff feel. It has a rectangular plastic connector at each end, with a small lever-like clip on top. To use it, align the connector with the Ethernet port on your device and push it in until you hear or feel a click. The clip helps secure the connection; you can press it down to remove the cable when needed.

2. Appearance

The router is slightly trapezoidal shaped and shall be placed on a flat surface, such as a table or a shelf. It comes with two thin, adjustable antennas attached to the back.

First, locate two short protruding cylinders with one on each side. They are on the back panel. Connect the antenna's threaded end to the cylinder interface, and rotate to secure. Place all antennas to point straight up for the best signal.

Then, locate four small plastic footpads on the bottom of the router and place your router with footpads facing down.

Next, face directly to the back panel. You'll find four ports and a few buttons lined up in a row. Here’s what they are, from left to right:

Power Slot: A round port. Plug in the provided power adapter to connect the router to the power socket.
Power Button: A round protruding button. To turn on your router, press it and wait about 2 minutes for the router to boot up. To turn off your router, press and immediately release it.
Three 1Gbps LAN Ports (1-3): Three square RJ-45 Ethernet ports, for connecting additional wired devices.
1Gbps LAN/WAN Port: A square RJ-45 Ethernet port. It defaults to a WAN port and can connect the router to a modem or an Ethernet outlet, or other internet services.
RESET Button: A tiny recessed hole (needs a pin to press). To reset the router to factory default settings, press for 2 seconds and release. Then wait about 2 minutes for it to restart.
WPS/Wi-Fi Button: A small round protruding button. To connect via WPS, press and immediately release the button, then press the WPS button on your device to connect via WPS. Press and hold the button for about 2 seconds, then release the button to turn the router’s Wi-Fi on or off.
SIM Card Slot: An oval card slot for inserting the Nano SIM Card. When inserting the card, keep the router properly placed, then put the card’s golden contacts down and the notched corner towards the upper left corner. Next insert it horizontally into the slot until you hear or feel a click.

On the bottom of the router, there is a recessed label. This label includes: the router’s default network name (SSID), the MAC address, and a QR code for scanning to connect to the default Wi-Fi.

Step 2. Set Up Your Router

1. Position your router. Make sure that the router is within reach of an AC power outlet and near Ethernet cables for wired devices. If possible, try moving it closer to a window for better signal.

2. Scan the QR code below to download and install the Tether app. Then follow the app instructions to set up your router.

Scan the QR code to download Tether App

Alternatively, you can click the button below to download and install the Tether app for iOS or Android.

Note: Please remain online (Wi-Fi or mobile data) throughout the app download and login steps.

Tip: You can also cable and set up your router with a web browser by visiting http://tplinkmodem.net or http://192.168.1.1. For detailed information, please refer to the router’s quick installation guide or user guide.

Support

For technical support, replacement services, user guides, and other information about your product model, please visit https://www.tp-link.com/support/

*TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directive 2019/882/EU. The original EU Declaration of Conformity may be found at https://www.tp-link.com/en/support/ce/