Search
Search

Download for EAP320 V2

Por favor escolha a versão de hardware:

V2

>Como identificar a versão de hardware num dispositivo TP-Link?

IMPORTANTE: A versão do modelo e de hardware varia de acordo com a região (EU/US). Consulte o site TP-Link da região correcta de acordo com a origem do produto.
Product Overview
Documentos
AC1200 Wireless Dual Band Gigabit Ceiling Mount Access Point
EAP320

Vídeo de Configuração

  • How to manage TP-Link EAPs centrally via the Software Controller

    This video demonstrates how to manage TP-Link EAPs centrally via the Software Controller. The setup consists of three steps:
    • Install the Software
    • Configure Discovery Utility (If your EAPs and the Controller Host are on different subnets)
    • Configure Software Controller

    THIS VIDEO APPLIES TO:
    • All TP-Link EAP models (except EAP120 and EAP220)
    • Omada Software Controller
    • Mass EAPs (usually more than three)

    Apreender mais

  • How to set up a TP Link EAP via your mobile phone

    This video demonstrates how to set up a TP-Link EAP via your mobile phone. The setup consists of four steps:
    • Connect the EAP to the network
    • Download the Omada APP
    • Connect to the EAP's wireless network
    • Set up the EAP using the Omada APP

    THIS VIDEO APPLIES TO:
    • All TP-Link EAP models. (except EAP120 and EAP220)
    • A small number (1-3) of EAPs.

    Apreender mais

  • How to setup the OC200 via a web browser

    This video will demonstrate how to set up the OC200 via a web browser. The setup consists of six steps:
    • Connect the OC200 to your local network.
    • Get ready for setup.
    • Create a TP-Link ID.
    • Log into your TP-Link ID.
    • Add the OC200 to your TP-Link ID.
    • Follow the wizard to set up the OC200.

    THIS VIDEO APPLIES TO:
    • All TP-Link EAP models (except EAP120 and EAP220)
    • Omada Cloud Controller OC200
    • Mass EAPs (usually more than three)

    Apreender mais

  • How to setup the OC200 via your mobile phone

    This video will demonstrate how to set up the OC200 via your mobile phone. You need to use the Omada APP to complete the setup. The setup consists of six steps:
    • Connect the OC200 to your local network.
    • Get ready for setup.
    • Create a TP-Link ID.
    • Log into your TP-Link ID.
    • Add the OC200 to your TP-Link ID.
    • Follow the wizard to set up the OC200.
    THIS VIDEO APPLIES TO:
    • All TP-Link EAP models (except EAP120 and EAP220)
    • Omada Cloud Controller OC200
    • Mass EAPs (usually more than three)

    Apreender mais

  • How to manage TP-Link EAPs centrally from a remote place via a web browser

    You can manage TP-Link EAPs at any time from anywhere with the Cloud Access function of our Omada Controller Software. This video introduces both the application scenario and concrete steps you can follow. Don't hesitate to give it a try.
    THIS VIDEO APPLIES TO:
    • All TP-Link EAP models (except EAP120 and EAP220)
    • Omada Controller Software (version 3.0.2 or above)
    • Mass EAPs (usually more than three)

    Apreender mais

  • How to Set up a TP-Link EAP via Web browser

    This video will demonstrate how to set up a TP-Link EAP via a web browser. The setup consists of three steps:
    1. Connect the EAP to the network
    2. Log into the EAP (via a wired/wireless connection)
    3. Change the default SSID
    This video is suitable for users with a small number (1-3) of EAPs .

    Apreender mais

Feature Filter: Tudo Configuration GuideQ&A of functional explanation or specification parametersUser Application RequirementTroubleshooting

FAQs

Firmware

Atualização de firmware pode resolver problemas da versão de firmware anterior e melhorar o seu desempenho atual.

Para atualizar

IMPORTANTE: Para evitar falhas de atualização, leia o seguinte, antes de prosseguir com o processo de atualização

  • Verifique a versão de hardware do seu dispositivo para a versão de firmware correta. Atualização incorreta de firmware pode danificar o seu dispositivo e anular a garantia. （ Normalmente V1.x = V1）
    NÃO é recomendado atualizar o firmware de outra região. Por favor clique aqui escolher a sua região e efetuar o download da versão de firmware adequado. (O firmware EU (Europa) e US (Estados Unidos) dispõe de versões de hardware diferentes)
  • NÃO desligue a energia durante o processo de atualização, pode causar danos permanentes ao produto.
  • NÃO atualize o firmware através de ligações Wi-Fi, expeto nos casos onde não dispõe de portas rede LAN/Ethernet no dispositivo TP-Link.
  • Recomenda-se que os utilizadores interrompam todos os acessos à Internet ou simplesmente desconectem a ligação à Internet do dispositivo antes de efetuar a atualização.
  • Para extrair o conteúdo com o ficheiro de atualização, recomendamos a utilização de programas de descompressão, como por exemplo, WinZIP, WinRAR ou 7-Zip.
EAP320(EU)_V2_1.4.0 Build 20180925
Data de Publicação: 2018-10-16 Idioma: Inglês Tamanho: 7.73 MB

Recommended Controller Software Version:  Omada Controller v 2.6.x or above

 

New Features/Improvements:

1. Support Omada APP management method.

2. Support HTTPS redirection of portal authentication page.

3. Support URL Free Authentication Policy

4. Support rate limit function for a single client. (If you have set SSID, Client, Voucher rate limit together, the minimum limit value will take effect.)

5. Increase the priority of DHCP message and EAPOL message, optimize the correlation process under the pressure of huge traffic

6. Omada Controller increased the synchronization update process when the IP address of EAP is changed

7. EAP will report Client RSSI information to Omada Controller.

8. The hardware version will be displayed as 1.0/2.0 in the management page.

 

Bug Fixed:

1. Fixed the bug that EAP will reboot automatically when Airtime Fairness function is enabled.

2. Fixed the bug that wireless clients may be displayed with abnormal IP address in Omada Controller.

3. Optimized the problem that EAP will be disconnected from Omada Controller.

 

Notes:

1. For EAP320 (EU)_V1/V2 only.

2. Your device's configuration won't be lost after upgrading.
EAP320(EU)_V2_170930
Data de Publicação: 2017-09-30 Idioma: Inglês Tamanho: 7.63 MB

Recommended Controller Software Version: Omada Controller v2.5.x

New Features/Improvements:

1. Support new SMS, Facebook and other authentication methods of Omada Controller 2.5.x.

2. Voucher supports speed limit of clients.

Bug Fixed:

1. Web management pages have syntax errors or inconsistent formats

2. EAP320 cannot be managed across different subnets when management VLAN is enabled.

Notes:

1. For EAP320 (EU) v2

2. Your device's configuration won't be lost after upgrading.
EAP320(EU)_V2_170725
Data de Publicação: 2017-07-25 Idioma: Inglês Tamanho: 7.60MB

Recommended Controller Software Version: Omada Controller v2.4.x

New Features/Improvements:

Enhance the capability of anti-interference.

Bug Fixed:

Fix the bug that the Security Mode will turn to None if using a space character in the WPA/WPA2-PSK password.

Notes:

1. For EAP320 (EU) v2.

2. Your device's configuration won't be lost after upgrading.

Utilização de firmware de terceiros em produtos TP-Link

Alguns produtos TP-Link permitem a substituição de firmware oficial por firmware de terceiros (Por exemplo DD-WRT). A TP-Link não se sente obrigada a facultar assistência e suporte e não garante estabilidade nem a performance de firmwares de terceiros. Danos provocados pela utilização de firmwares de terceiros, inviabiliza automaticamente a politica de garantia dos nossos produtos.

Código Open Source para Programadores (GPL)

Nota: Os produtos TP-Link contêm parcialmente código de software desenvolvido por terceiros, incluindo software que foi submetido ao GNU General Public License ("GPL"), Versão 1/Versão 2/Versão 3 ou GNU Lesser General Public License ("LGPL"). Pode utilizar a respetiva condição de software seguindo os termos da licença GPL.

Pode rever, imprimir e efetuar o download dos respetivos termos da licença GPL aqui. Terá acesso ao Código Fonte GPL dos respetivos softwares utilizados nos produtos TP-Link para download e investigação, incluindo a lista de software TP-Link que contêm software GPL ao abrigo do Centro de Código GPL.

Os respetivos programas são distribuídos sem qualquer garantia e suporte. Reveja a licença de GNU - General Public License para mais detalhe.

Controller Software

The EAP Controller is used to manage multiple EAPs intensively.

Data de Publicação: 2020-04-20 Idioma: Inglês Tamanho: 120.54MB
Sistema operativo: Windows 7/8/10/Server

New Feature/Enhancement:

1. Added the feature that the system logs can be exported.

2. Changed the priority that non-administrator role cannot change the history data retention settings.

3. Optimized the UI of Statistics in Omada Controller.

 

Bug Fixed:

1. Fixed the bug that the External Web Portal cannot authenticate successfully if the SSID of this portal has special characters.

2. Fixed the bug that the Cloud Access cannot be displayed normally in the low version of Firefox.

3. Fixed the bug that Omada Controller allow any user to read the files of controller.

4. Fixed the bug that controller will report an error when Top Usage data is empty.

 

Notes:

1. To use Omada Controller 3.2.X new features, you need to upgrade your EAP's firmware to the corresponding version.

2. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

3. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.X or earlier version.
Data de Publicação: 2020-04-20 Idioma: Inglês Tamanho: 124.46MB
Sistema operativo: Windows 7/8/10/Server

New Feature/Enhancement:

1. Added the feature that the system logs can be exported.

2. Changed the priority that non-administrator role cannot change the history data retention settings.

3. Optimized the UI of Statistics in Omada Controller.

 

Bug Fixed:

1. Fixed the bug that the External Web Portal cannot authenticate successfully if the SSID of this portal has special characters.

2. Fixed the bug that the Cloud Access cannot be displayed normally in the low version of Firefox.

3. Fixed the bug that Omada Controller allow any user to read the files of controller.

4. Fixed the bug that controller will report an error when Top Usage data is empty.

 

Notes:

1. To use Omada Controller 3.2.X new features, you need to upgrade your EAP's firmware to the corresponding version.

2. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

3. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.X or earlier version.
Data de Publicação: 2020-04-20 Idioma: Inglês Tamanho: 99.4MB
Sistema operativo: Ubuntu 14.04/16.04/17.04/18.04/Debian 9.8

Bug Fixed:

1. Fixed the bug that Omada Controller allow any user to read the files of controller.

2. Fixed the bug that controller will report an error when Top Usage data is empty. 

 

Notes:

1. To use new features on Omada Controller 3.2.X, you need to upgrade your EAP's firmware to the corresponding version.

2. The Omada Controller program needs to use the system's netstat command. If the Linux system does not have net-tools installed (which contain the netstat command), the program may not be able to run normally.

3. Support 64-bit Linux operating system including Ubuntu 14.04/16.04/17.04/18.04/Debian 9.8

4. Built-in JRE 1.8 Java environment.

5. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

6. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.8.
Data de Publicação: 2020-04-20 Idioma: Inglês Tamanho: 125.64MB
Sistema operativo: Ubuntu 14.04/16.04/17.04/18.04, CentOS 6.x/7.x and Fedora 20 or above, Debian 9.8.

Bug Fixed:

1. Fixed the bug that Omada Controller allow any user to read the files of controller.

2. Fixed the bug that controller will report an error when Top Usage data is empty. 

 

Notes:

1. To use new features on Omada Controller 3.2.x, you need to upgrade your EAP's firmware to the corresponding version.

2. The Omada Controller program needs to use the system's netstat command. If the Linux system does not have net-tools installed (which contain the netstat command), the program may not be able to run normally.

3. Support 64-bit Linux operating system including Ubuntu 14.04/16.04/17.04/18.04, CentOS 6.x/7.x and Fedora 20 or above, Debian 9.8.

4. Built-in JRE 1.8 Java environment.

5. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

6. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.8.

7. When upgrading from Controller 2.5.3 Linux to this version via install.sh, you need to uninstall old version of Controller first.
Data de Publicação: 2020-04-09 Idioma: Inglês Tamanho: 99.39MB
Sistema operativo: Ubuntu 14.04/16.04/17.04/18.04/Debian 9.8

New Feature/Enhancement:

1. Add the feature that the system logs can be exported.

2. Change the priority that non-administrator role cannot change the history data retention settings.

3. Optimize the UI of Statistics in Omada Controller.

 

Bug Fixed:

1. Fix the bug that the External Web Portal cannot authenticate successfully if the SSID of this portal has special characters.

2. Fix the bug that the Cloud Access cannot be displayed normally in the low version of Firefox.

 

Notes:

1. To use new features on Omada Controller 3.2.X, you need to upgrade your EAP's firmware to the corresponding version.

2. The Omada Controller program needs to use the system's netstat command. If the Linux system does not have net-tools installed (which contain the netstat command), the program may not be able to run normally.

3. Support 64-bit Linux operating system including Ubuntu 14.04/16.04/17.04/18.04/Debian 9.8

4. Built-in JRE 1.8 Java environment.

5. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

6. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.8.
Data de Publicação: 2020-04-09 Idioma: Inglês Tamanho: 123.36MB
Sistema operativo: Ubuntu 14.04/16.04/17.04/18.04, CentOS 6.x/7.x and Fedora 20 or above, Debian 9.8.

New Feature/Enhancement:

1. Add the feature that the system logs can be exported.

2. Change the priority that non-administrator role cannot change the history data retention settings.

3. Optimize the UI of Statistics in Omada Controller.

 

Bug Fixed:

1. Fix the bug that the External Web Portal cannot authenticate successfully if the SSID of this portal has special characters.

2. Fix the bug that the Cloud Access cannot be displayed normally in the low version of Firefox.

 

 

Notes:

1. To use new features on Omada Controller 3.2.x, you need to upgrade your EAP's firmware to the corresponding version.

2. The Omada Controller program needs to use the system's netstat command. If the Linux system does not have net-tools installed (which contain the netstat command), the program may not be able to run normally.

3. Support 64-bit Linux operating system including Ubuntu 14.04/16.04/17.04/18.04, CentOS 6.x/7.x and Fedora 20 or above, Debian 9.8.

4. Built-in JRE 1.8 Java environment.

5. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

6. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.8.

7. When upgrading from Controller 2.5.3 Linux to this version via install.sh, you need to uninstall old version of Controller first.
Data de Publicação: 2020-01-21 Idioma: Inglês Tamanho: 120.53MB
Sistema operativo: Windows 7/8/10/Server

New Feature/Enhancement:

1. Expand the number of Omada Controller’s User Account to 500.  

2. Optimize the External Portal Server to support URL with parameters.

 

Notes:

1. To use Omada Controller 3.2.X new features, you need to upgrade your EAP's firmware to the corresponding version.

2. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

3. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.X or earlier version.

 
Data de Publicação: 2020-01-21 Idioma: Inglês Tamanho: 124.45MB
Sistema operativo: Windows 7/8/10/Server

New Feature/Enhancement:

1. Expand the number of Omada Controller’s User Account to 500.  

2. Optimize the External Portal Server to support URL with parameters.

 

Notes:

1. To use Omada Controller 3.2.X new features, you need to upgrade your EAP's firmware to the corresponding version.

2. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

3. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.X or earlier version.
Data de Publicação: 2020-01-16 Idioma: Inglês Tamanho: 123.35MB
Sistema operativo: Ubuntu 14.04/16.04/17.04/18.04, CentOS 6.x/7.x and Fedora 20 or above, Debian 9.8.

New Feature/Enhancement:

1. Change the mechanism that when adopting an EAP, the Controller will retain the IP configuration of EAP in Standalone mode.

2. Change the mechanism that multiple Omada Controllers can run on the same subnet.

3. Add the button of “Start Omada Controller after installation” and check it by default.

4. Extend the Max Associated Clients in Load Balance to 255.

5. Optimize the UI of Channel Utilization.

6. Optimize the authentication page of portal.

7. Optimize the UI of the portal that you cannot click Apply when you are uploading a photo.

8. Optimize the External Portal Server to support URL with parameters.

 

Bug Fixed:

1. Fixed the bug that the page of MAC filter may not display all groups when there are more than 5 groups.

2. Fixed the bug that after deleting a site, the Voucher code and Local user of this site still exist.

3. Fixed the bug that the site configuration will fail to restore when the imported site contains same Voucher code as the current Controller.

4. Fixed the bug that when mesh AP is powered off during upgrade, Controller may fail to upgrade other APs, with a prompt message “Other APs are upgrading”.

 

Notes:

1. To use new features on Omada Controller 3.2.x, you need to upgrade your EAP's firmware to the corresponding version.

2. The Omada Controller program needs to use the system's netstat command. If the Linux system does not have net-tools installed (which contain the netstat command), the program may not be able to run normally.

3. Support 64-bit Linux operating system including Ubuntu 14.04/16.04/17.04/18.04, CentOS 6.x/7.x and Fedora 20 or above, Debian 9.8.

4. Built-in JRE 1.8 Java environment.

5. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

6. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.8.

7. When upgrading from Controller 2.5.3 Linux to this version via install.sh, you need to uninstall old version of Controller first.

 
Data de Publicação: 2020-01-16 Idioma: Inglês Tamanho: 99.4MB
Sistema operativo: Ubuntu 14.04/16.04/17.04/18.04/Debian 9.8

New Feature/Enhancement:

1. Change the mechanism that when adopting an EAP, the Controller will retain the IP configuration of EAP in Standalone mode.

2. Change the mechanism that multiple Omada Controllers can run on the same subnet.

3. Add the button of “Start Omada Controller after installation” and check it by default.

4. Extend the Max Associated Clients in Load Balance to 255.

5. Optimize the UI of Channel Utilization.

6. Optimize the authentication page of portal.

7. Optimize the UI of the portal that you cannot click Apply when you are uploading a photo.

8. Optimize the External Portal Server to support URL with parameters.

 

Bug Fixed:

1. Fixed the bug that the page of MAC filter may not display all groups when there are more than 5 groups.

2. Fixed the bug that after deleting a site, the Voucher code and Local user of this site still exist.

3. Fixed the bug that the site configuration will fail to restore when the imported site contains same Voucher code as the current Controller.

4. Fixed the bug that when mesh AP is powered off during upgrade, Controller may fail to upgrade other APs, with a prompt message “Other APs are upgrading”.

 

Notes:

1. To use new features on Omada Controller 3.2.X, you need to upgrade your EAP's firmware to the corresponding version.

2. The Omada Controller program needs to use the system's netstat command. If the Linux system does not have net-tools installed (which contain the netstat command), the program may not be able to run normally.

3. Support 64-bit Linux operating system including Ubuntu 14.04/16.04/17.04/18.04/Debian 9.8

4. Built-in JRE 1.8 Java environment.

5. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

6. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.8.
Data de Publicação: 2020-01-09 Idioma: Inglês Tamanho: 120.53MB
Sistema operativo: Windows 7/8/10/Server

New Feature/Enhancement:

1. Change the mechanism that when adopting an EAP, the Controller will retain the IP configuration of EAP in Standalone mode.

2. Change the mechanism that multiple Omada Controllers can run on the same subnet.

3. Add the button of “Start Omada Controller after installation” and check it by default.

4. Extend the Max Associated Clients in Load Balance to 255.

5. Optimize the UI of Channel Utilization.

6. Optimize the authentication page of portal.

7. Optimize the UI of the portal that you cannot click Apply when you are uploading a photo.

 

Bug Fixed:

1. Fixed the bug that the page of MAC filter may not display all groups when there are more than 5 groups.

2. Fixed the bug that after deleting a site, the Voucher code and Local user of this site still exist.

3. Fixed the bug that the site configuration will fail to restore when the imported site contains same Voucher code as the current Controller.

4. Fixed the bug that when mesh AP is powered off during upgrade, Controller may fail to upgrade other APs, with a prompt message “Other APs are upgrading”.

 

Notes:

1. To use Omada Controller 3.2.X new features, you need to upgrade your EAP's firmware to the corresponding version.

2. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

3. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.X or earlier version.
Data de Publicação: 2020-01-09 Idioma: Inglês Tamanho: 124.44MB
Sistema operativo: Windows 7/8/10/Server

New Feature/Enhancement:

1. Change the mechanism that when adopting an EAP, the Controller will retain the IP configuration of EAP in Standalone mode.

2. Change the mechanism that multiple Omada Controllers can run on the same subnet.

3. Add the button of “Start Omada Controller after installation” and check it by default.

4. Extend the Max Associated Clients in Load Balance to 255.

5. Optimize the UI of Channel Utilization.

6. Optimize the authentication page of portal.

7. Optimize the UI of the portal that you cannot click Apply when you are uploading a photo.

 

Bug Fixed:

1. Fixed the bug that the page of MAC filter may not display all groups when there are more than 5 groups.

2. Fixed the bug that after deleting a site, the Voucher code and Local user of this site still exist.

3. Fixed the bug that the site configuration will fail to restore when the imported site contains same Voucher code as the current Controller.

4. Fixed the bug that when mesh AP is powered off during upgrade, Controller may fail to upgrade other APs, with a prompt message “Other APs are upgrading”.

 

Notes:

1. To use Omada Controller 3.2.X new features, you need to upgrade your EAP's firmware to the corresponding version.

2. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

3. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.X or earlier version.
Data de Publicação: 2019-11-08 Idioma: Inglês Tamanho: 99.4MB
Sistema operativo: Ubuntu 14.04/16.04/17.04/18.04/Debian 9.8

New Feature/Enhancement:

1. Add “Select Page” feature on voucher management page.

2. Change default status of “Terms of Service” on default portal page to uncheck.

3. Optimize the “Free Authentication Policy” to support URL with suffixes.

4. Change the default status of new added “Free Authentication Policy” to enable.

 

Bug Fixed:

1. Fixed the bug that when clients disconnect from the Facebook portal, the connection time and traffic usage of these clients may be zero in the log.

2. Fixed the bug that AP may disconnect from Omada Controller when it is upgrading the firmware.

3. Fixed the bug that in some cases, the channel configuration of 2.4G frequency may show up in 5G by mistake.

4. Fixed the bug that the configuration of SSID will not be issued correctly when changing the WLAN Group on the provisioning status.

 

Notes:

1. To use new features on Omada Controller 3.2.X, you need to upgrade your EAP's firmware to the corresponding version.

2. The Omada Controller program needs to use the system's netstat command. If the Linux system does not have net-tools installed (which contain the netstat command), the program may not be able to run normally.

3. Support 64-bit Linux operating system including Ubuntu 14.04/16.04/17.04/18.04/Debian 9.8

4. Built-in JRE 1.8 Java environment.

5. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

6. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.8.
Data de Publicação: 2019-11-08 Idioma: Inglês Tamanho: 123.35MB
Sistema operativo: Ubuntu 14.04/16.04/17.04/18.04, CentOS 6.x/7.x and Fedora 20 or above, Debian 9.8.

New Feature/Enhancement:

1. Add “Select Page” feature on the management page of vouchers.

2. Change the default status of “Terms of Service” to uncheck.

3. Optimize the “Free Authentication Policy” to support URL with suffixes.

4. Change the default status of new added “Free Authentication Policy” to enable.

 

Bug Fixed:

1. Fixed the bug that when clients disconnect from the Facebook portal, the connection time and traffic usage of these clients may be zero in the log.

2. Fixed the bug that AP may disconnect from Omada Controller when it is upgrading the firmware.

3. Fixed the bug that in some cases, the channel configuration of 2.4G frequency may show up in 5G by mistake.

4. Fixed the bug that the configuration of SSID will not be issued correctly when changing the WLAN Group on the provisioning status.

 

 

Notes:

1. To use new features on Omada Controller 3.2.x, you need to upgrade your EAP's firmware to the corresponding version.

2. The Omada Controller program needs to use the system's netstat command. If the Linux system does not have net-tools installed (which contain the netstat command), the program may not be able to run normally.

3. Support 64-bit Linux operating system including Ubuntu 14.04/16.04/17.04/18.04, CentOS 6.x/7.x and Fedora 20 or above, Debian 9.8.

4. Built-in JRE 1.8 Java environment.

5. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

6. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.8.

7. When upgrading from Controller 2.5.3 Linux to this version via install.sh, you need to uninstall old version of Controller first.
Data de Publicação: 2019-11-08 Idioma: Inglês Tamanho: 120.52MB
Sistema operativo: Windows 7/8/10/Server

New Feature/Enhancement:

1. Add “Select Page” feature on the voucher management page.

2. Change the default status of “Terms of Service” on default portal page to uncheck.

3. Optimize the “Free Authentication Policy” to support URL with suffixes.

4. Change the default status of new added “Free Authentication Policy” to enable.

 

Bug Fixed:

1. Fixed the bug that when clients disconnect from the Facebook portal, the connection time and traffic usage of these clients may be zero in the log.

2. Fixed the bug that AP may disconnect from Omada Controller when it is upgrading the firmware.

3. Fixed the bug that in some cases, the channel configuration of 2.4G frequency may show up in 5G by mistake.

4. Fixed the bug that the configuration of SSID will not be issued correctly when changing the WLAN Group on the provisioning status.

 

Notes:

1. To use Omada Controller 3.2.x new features, you need to upgrade your EAP's firmware to the corresponding version.

2. Once upgraded to this version of Omada Controller, you will NOT be able to downgrade to an earlier version.

3. Portal configuration will be lost after upgrading to Omada Controller 3.2.X from 2.4.X or earlier version.

4. You are recommended to create a backup before upgrading, or you will not be permitted to install this version of Omada Controller.
Data de Publicação: 2019-11-08 Idioma: Inglês Tamanho: 124.43MB
Sistema operativo: Windows 7/8/10/Server

New Feature/Enhancement:

1. Add “Select Page” feature on the voucher management page.

2. Change the default status of “Terms of Service” on default portal page to uncheck.

3. Optimize the “Free Authentication Policy” to support URL with suffixes.

4. Change the default status of new added “Free Authentication Policy” to enable.

 

Bug Fixed:

1. Fixed the bug that when clients disconnect from the Facebook portal, the connection time and traffic usage of these clients may be zero in the log.

2. Fixed the bug that AP may disconnect from Omada Controller when it is upgrading the firmware.

3. Fixed the bug that in some cases, the channel configuration of 2.4G frequency may show up in 5G by mistake.

4. Fixed the bug that the configuration of SSID will not be issued correctly when changing the WLAN Group on the provisioning status.

 

Notes:

1. To use Omada Controller 3.2.x new features, you need to upgrade your EAP's firmware to the corresponding version.

2. Once upgraded to this version of Omada Controller, you will NOT be able to downgrade to an earlier version.

3. Portal configuration will be lost after upgrading to Omada Controller 3.2.X from 2.4.X or earlier version.

4. You are recommended to create a backup before upgrading, or you will not be permitted to install this version of Omada Controller.
Data de Publicação: 2019-07-26 Idioma: Inglês Tamanho: 99.23MB
Sistema operativo: Ubuntu 14.04/16.04/17.04/18.04/Debian 9.8

New Feature/Enhancement:

1. Optimize the performance of Controller to manage up to 1500 EAPs.

2. Optimize the interactive process between EAP and Controller to decrease the processing time.

3. Limit the entry number of client/client history/guest to 1.2 million/1.2 million /6 million.

4. Optimize display page of map and log when there are a lot of entries.

 

Bug Fixed:

1. Fixed the bug that CPU and memory may be highly used when Fast Roaming is enabled.

2. Fixed the bug that Omada Controller reports timeout error when adopting multiple EAPs simultaneously.

3. Fixed the bug that Controller will print all Voucher codes even only some of the codes are selected.

 

Notes:

1. To use new features on Omada Controller 3.2.X, you need to upgrade your EAP's firmware to the corresponding version.

2. The Omada Controller program needs to use the system's netstat command. If the Linux system does not have net-tools installed (which contain the netstat command), the program may not be able to run normally.

3. Support 64-bit Linux operating system including Ubuntu 14.04/16.04/17.04/18.04/Debian 9.8

4. Built-in JRE 1.8 Java environment.

5. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

6. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.8.

 
Data de Publicação: 2019-07-26 Idioma: Inglês Tamanho: 123.15MB
Sistema operativo: Ubuntu 14.04/16.04/17.04/18.04, CentOS 6.x/7.x and Fedora 20 or above, Debian 9.8.

New Feature/Enhancement:

1. Optimize the performance of Controller to manage up to 1500 EAPs.

2. Optimize the interactive process between EAP and Controller to decrease the processing time.

3. Limit the entry number of client/client history/guest to 1.2 million/1.2 million /6 million.

4. Optimize display page of map and log when there are a lot of entries.

 

Bug Fixed:

1. Fixed the bug that CPU and memory may be highly used when Fast Roaming is enabled.

2. Fixed the bug that Omada Controller reports timeout error when adopting multiple EAPs simultaneously.

3. Fixed the bug that Controller will print all Voucher codes even only some of the codes are selected.

 

Notes:

1. To use new features on Omada Controller 3.2.x, you need to upgrade your EAP's firmware to the corresponding version.

2. The Omada Controller program needs to use the system's netstat command. If the Linux system does not have net-tools installed (which contain the netstat command), the program may not be able to run normally.

3. Support 64-bit Linux operating system including Ubuntu 14.04/16.04/17.04/18.04, CentOS 6.x/7.x and Fedora 20 or above, Debian 9.8.

4. Built-in JRE 1.8 Java environment.

5. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

6. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.8.

7. When upgrading from Controller 2.5.3 Linux to this version via install.sh, you need to uninstall old version of Controller first.
Data de Publicação: 2019-07-04 Idioma: Inglês Tamanho: 120.29MB
Sistema operativo: Windows 7/8/10/Server

New Feature/Enhancement:

1. Optimize the performance of Controller to manage up to 1500 EAPs.

2. Optimize the interactive process between EAP and Controller to decrease the process time.

3. Limit the entry number of client/client history/guest to 1.2 million/1.2 million /6 million.

4. Optimize display page of map and log when there are a lot of entries.

 

Bug Fixed:

1. Fixed the bug that CPU and memory may be highly used when Fast Roaming is enabled.

2. Fixed the bug that Omada Controller reports timeout error when adopting multiple EAPs simultaneously.

3. Fixed the bug that Controller will print all Voucher codes even only some of the codes are selected.

 

Notes:

1. To use Omada Controller 3.2.x new features, you need to upgrade your EAP's firmware to the corresponding version.

2. Once upgraded to this version of Omada Controller, you will NOT be able to downgrade to an earlier version.

3. Portal configuration will be lost after upgrading to Omada Controller 3.2.X from 2.4.X or earlier version.
Data de Publicação: 2019-07-04 Idioma: Inglês Tamanho: 124.2MB
Sistema operativo: Windows 7/8/10/Server

New Feature/Enhancement:

1. Optimize the performance of Controller to manage up to 1500 EAPs.

2. Optimize the interactive process between EAP and Controller to decrease the process time.

3. Limit the entry number of client/client history/guest to 1.2 million/1.2 million /6 million.

4. Optimize display page of map and log when there are a lot of entries.

 

Bug Fixed:

1. Fixed the bug that CPU and memory may be highly used when Fast Roaming is enabled.

2. Fixed the bug that Omada Controller reports timeout error when adopting multiple EAPs simultaneously.

3. Fixed the bug that Controller will print all Voucher codes even only some of the codes are selected.

 

Notes:

1. To use Omada Controller 3.2.x new features, you need to upgrade your EAP's firmware to the corresponding version.

2. Once upgraded to this version of Omada Controller, you will NOT be able to downgrade to an earlier version.

3. Portal configuration will be lost after upgrading to Omada Controller 3.2.X from 2.4.X or earlier version.
Data de Publicação: 2019-03-08 Idioma: Inglês Tamanho: 123.6MB
Sistema operativo: Windows 7/8/10/Server

New Feature/Enhancement:

1. Merge 2.4GHz and 5GHz SSID.

2. Add Guest Network function.

3. Optimize log field and content.

4. Add SSID Radius accounting to WPA-Enterprise security mode.

5. Optimize the site list which allows us to inquire the specific site based on the site name and add new entrance for the hotspot.

6. Add SSL encryption in Log Server, and Log setting/Mail Server can be only accessed by administrator account.

7. Add Layer-3 Accessibility in SSH.

8. Add Mesh settings to Backup and Restore file.

9. Add CHAP encryption and NAS ID in Radius portal authentication and the Radius Client role is transferred from EAP to Omada Controller.

10. Add SSID MAC Authentication to none security mode.

11. Add channel utilization function.

12. Add Full-Sector DFS function in Mesh network.

13. Channel limit is revised from private configuration to site settings.

14. Support inputting domain name in SMTP server.

 

Notes:

1. The log will be cleared when you upgrade the software from version 3.0.x to version 3.1.4.

2. Add push notification to Omada APP of version 2.1.4 or above when EAP is connected/disconnected from Omada Controller.

3. This version of Omada Controller is applied to Omada APP of version 2.1.4 or above.

4. When you upgrade your controller or backup files from lower version, the 2.4GHz and 5GHz SSID entries with the same name will be merged and it will inherit the parameters of the original 2.4GHz SSID.

5. If you use External Radius Server with External Web Portal in old version controller, pay attention that the API has been changed in this version, thus you have to modify your External Web Portal, refer to FAQ-2390 for more details.

6. The log generated by EAP will be managed and storaged by Controller if you manage EAPs by Omada Controller.

7. Channel utilization will take effect only with new firmware.
Data de Publicação: 2019-03-08 Idioma: Inglês Tamanho: 127.5MB
Sistema operativo: Windows 7/8/10/Server

New Feature/Enhancement:

1. Merge 2.4GHz and 5GHz SSID.

2. Add Guest Network function.

3. Optimize log field and content.

4. Add SSID Radius accounting to WPA-Enterprise security mode.

5. Optimize the site list which allows us to inquire the specific site based on the site name and add new entrance for the hotspot.

6. Add SSL encryption in Log Server, and Log setting/Mail Server can be only accessed by administrator account.

7. Add Layer-3 Accessibility in SSH.

8. Add Mesh settings to Backup and Restore file.

9. Add CHAP encryption and NAS ID in Radius portal authentication and the Radius Client role is transferred from EAP to Omada Controller.

10. Add SSID MAC Authentication to none security mode.

11. Add channel utilization function.

12. Add Full-Sector DFS function in Mesh network.

13. Channel limit is revised from private configuration to site settings.

14. Support inputting domain name in SMTP server.

 

Notes:

1. The log will be cleared when you upgrade the software from version 3.0.x to version 3.1.4.

2. Add push notification to Omada APP of version 2.1.4 or above when EAP is connected/disconnected from Omada Controller.

3. This version of Omada Controller is applied to Omada APP of version 2.1.4 or above.

4. When you upgrade your controller or backup files from lower version, the 2.4GHz and 5GHz SSID entries with the same name will be merged and it will inherit the parameters of the original 2.4GHz SSID.

5. If you use External Radius Server with External Web Portal in old version controller, pay attention that the API has been changed in this version, thus you have to modify your External Web Portal, refer to FAQ-2390 for more details.

6. The log generated by EAP will be managed and storaged by Controller if you manage EAPs by Omada Controller.

7. Channel utilization will take effect only with new firmware.

EAP Discovery Tool

The EAP Discovery Tool can help the EAP Controller to adopt the EAP in L3 Network, and you can also use the EAP Discovery Tool to find the EAP’s IP address.

Data de Publicação: 2019-08-06 Idioma: Inglês Tamanho: 25.85 MB
Sistema operativo: WinXP/Vista/7/8/8.1/10/Server2008/Server2012/Mac OS X 10.7/10.8/10.9/10.10/10.11

Bug fixed:

1. Fixed the bug that the Discovery Utility may fail to find EAPs.

2. Fixed the bug that the Cancel button may overlap with the display box after managing APs.

 

Note:

1. This version of software can be used in both Windows and Mac operation system.

2. Double click the software or run the command “java –jar **.jar” to run the software on MacOS (**.jar is the name of this software).

3. To run this software, you need to install JRE 8.0 on your PC first.
Data de Publicação: 2019-06-14 Idioma: Inglês Tamanho: 23.54 MB
Sistema operativo: WinXP/Vista/7/8/8.1/10/Server2008/Server2012/Mac OS X 10.7/10.8/10.9/10.10/10.11

Bug fixed:

1. Fixed the bug that when the Discovery Utility issues Controller_IP to EAPs which are in factory status, Controller cannot batch manage the EAPs.

2. Fixed the bug that sometimes the Discovery Utility cannot find all EAPs when running in MacOS.

Note:

1. This version of software can be used in both Windows and Mac operation system.

2. Double click the software or run the command “java –jar **.jar” to run the software on MacOS(**.jar is the name of this software).

3. To run this software, you need to install JRE 8.0 on your PC.
Data de Publicação: 2018-07-24 Idioma: Inglês Tamanho: 84.16 MB
Sistema operativo: Mac OS X 10.7/10.8/10.9/10.10/10.11

New Feature/Enhancement:
1. Change name to "Omada Discovery Utility".
2. Update background picture during installation.
3. Limit the maximum length of controller hostname to 79.
 
Bug Fixed:
Fix the bug that searching in the search box will cause the software to hang.
 
Note:
Operating System: Mac OS X 10.7/10.8/10.9/10.10/10.11.

Emulators

Versão de firmware
Working Mode
Idioma
170930(EU)
-
Inglês

Feature Filter: Tudo EAP AdoptionPortalManagementQuick StartConfigurationConfiguration Example

Q&A

Feature Configuration Guide

T2700G-28TQ License Download
License Model: T2700G-28TQ-L1000

Find your product MAC and Serial Number.
License Key:
Product Serial Number:
Product MAC:
Checking code:

SubscriptionTP-Link takes your privacy seriously. For further details on TP-Link's privacy practices, see TP-Link's Privacy Policy.

Siga-nos

Sobre Nós
Comunicado de imprensa
Onde Comprar
Learning Center
Portugal / português
Copyright © TP-Link Technologies Co., Ltd. 2020. Todos os direitos reservados.