How to log into the web management page of the TL-MR3020
User Application Requirement
Updated 06-28-2022 08:23:54 AM290172
This Article Applies to:
TL-MR3020
Pembaruan terkini mungkin telah memperluas akses ke fitur yang dibahas dalam Tanya Jawab Umum ini. Kunjungi halaman dukungan produk Anda, pilih versi perangkat keras yang tepat untuk perangkat Anda, dan periksa bagian Lembar Data atau firmware untuk mengetahui penyempurnaan terbaru yang ditambahkan ke produk Anda. Harap perhatikan bahwa ketersediaan produk bervariasi menurut wilayah, dan model tertentu mungkin tidak tersedia di wilayah Anda.
The web-based management page is a built-in internal web server that does not require internet access. It does however require you device to be connected to the TP-Link router. This connection can be wired or wireless.
Note: Low version of your web browser may cause compatibility problem with the web-based interface(management page) of your device, such as unable to log into the interface, display incomplete features etc. It is strongly recommended to use a wired connection if you are going to change the router’s wireless settings or upgrade the firmware version of the router.
There are multiple working modes on the TL-MR3020.It requires different settings to access the web management page under different working mode.
In this article, we will explain how to access the web interface in different working modes.
3G/4G Mode & WISP Mode
3G/4G mode includes 3G/4G Only,3G/4G Preferred, WAN Only,WAN Preferred
Step 1:
Connect the TL-MR3020 directly to your computer’s Ethernet port by an Ethernet cable.
Step 2:
Power on the TL-MR3020 and switch it to 3G/4G or WISP mode.
Step 3:
Open a web browser such as Safari, GoogleChrome or Internet Explorer. At the top of the window in the address bar type 192.168.0.254 -> Press Enter
Enter the default User Name: admin
Enter the default Password: admin
Click OK
AP Mode
AP Mode includes Access Point,Repeater,Client,Bridge with AP.
Step 1:
Connect the TL-MR3020 directly to your computer’s Ethernet port by an Ethernet cable.
Step 2:
Power on the TL-MR3020 and switch it to AP mode.
Step 3:Set up a static IP on the computer
Initial Computer Setup– For Windows OS
1) Press Windows key and R key on the keyboard at the same time to open the Run application,type in ncpa.cpl->Press OK
2) Right Click Local Area Connection or Ethernet on Windows 8 & 8.1>Select Properties > Double Click Internet Protocol Version 4 (TCP/IPv4) or Internet Protocol (TCP/IP) on Windows XP.
3) Select “Use the Following IP address:”
Type the following information: IP address: 192.168.0.10 ; Subnet mask: 255.255.255.0->Click OK to exit->Click OK again to apply the settings.
Initial Computer Setup– For Mac OS X
Go to the Apple>System Preferences>Network> HighlightEthernet >Configure IPv4: Using DHCP with manual address
Input the IPv4 Address: 192.168.0.10
Click Apply
Step 4:
Open a Web Browser -> Type 192.168.0.254 in the address bar -> Press Enter
Enter the default User Name: admin
Enter the default Password: admin
Click OK
After the configuration of AP Mode, please remember to change the IP settings back as it was before.
Computer Setup Reversion
For Windows OS
Find Local Area Connection/Ethernet again>Select Properties > Double Click Internet Protocol Version 4 (TCP/IPv4) or Internet Protocol (TCP/IP) on Windows XP>Select “Obtainan IP address automatically” and “Obtain DNS server address automatically”
Click OK to exit
Click OK again to apply the settings.
For Mac OS X
Go to the Apple->System Preferences->Network-> Highlight Ethernet ->Configure IPv4: Using DHCP.
Click Apply.
Is this faq useful?
Your feedback helps improve this site.
What’s your concern with this article?
Dissatisfied with product
Too Complicated
Confusing Title
Does not apply to me
Too Vague
Other
Thank you
We appreciate your feedback. Click here to contact TP-Link technical support.
This website uses cookies to improve website navigation, analyze online activities and have the best possible user experience on our website. You can object to the use of cookies at any time. You can find more information in our privacy policy . Don’t show again
Your Privacy Choices
This website uses cookies to improve website navigation, analyze online activities and have the best possible user experience on our website. You can object to the use of cookies at any time. You can find more information in our privacy policy . Don’t show again
These cookies are necessary for the website to function and cannot be deactivated in your systems.
Analysis cookies enable us to analyze your activities on our website in order to improve and adapt the functionality of our website.
The marketing cookies can be set through our website by our advertising partners in order to create a profile of your interests and to show you relevant advertisements on other websites.
290172 
and R key on the keyboard at the same time to open the Run application,type in ncpa.cpl ->Press OK
