Setup Video

  • How to manage TP-Link EAPs centrally via the Software Controller

    This video demonstrates how to manage TP-Link EAPs centrally via the Software Controller. The setup consists of three steps:
    • Install the Software
    • Configure Discovery Utility (If your EAPs and the Controller Host are on different subnets)
    • Configure Software Controller

    THIS VIDEO APPLIES TO:
    • All TP-Link EAP models (except EAP120 and EAP220)
    • Omada Software Controller
    • Mass EAPs (usually more than three)

    Scopri

  • How to set up a TP Link EAP via your mobile phone

    This video demonstrates how to set up a TP-Link EAP via your mobile phone. The setup consists of four steps:
    • Connect the EAP to the network
    • Download the Omada APP
    • Connect to the EAP's wireless network
    • Set up the EAP using the Omada APP

    THIS VIDEO APPLIES TO:
    • All TP-Link EAP models. (except EAP120 and EAP220)
    • A small number (1-3) of EAPs.

    Scopri

  • How to manage TP-Link EAPs centrally from a remote place via a web browser

    You can manage TP-Link EAPs at any time from anywhere with the Cloud Access function of our Omada Controller Software. This video introduces both the application scenario and concrete steps you can follow. Don't hesitate to give it a try.
    THIS VIDEO APPLIES TO:
    • All TP-Link EAP models (except EAP120 and EAP220)
    • Omada Controller Software (version 3.0.2 or above)
    • Mass EAPs (usually more than three)

    Scopri

  • A Quick Overview of EAP Management Methods

    This video introduces how to choose the optimum method to manage TP-Link EAPs in your scenario.
    Here are 3 most common scenarios and their corresponding methods:
    • Manage 1 or 2 EAPs locally
    • Manage 3 or more EAPs locally
    • Manage 3 or more EAPs remotely
    When choosing the method, consider the following questions:
    1. Standalone Mode or Controller Mode?
    2. In Controller mode, what kind of controller will you use, an OC200 or a PC with Omada Software Controller?
    3. What kind of user interface will you use, a web browser or the Omada app?

    Scopri

  • How to Set up a TP-Link EAP via Web browser

    This video will demonstrate how to set up a TP-Link EAP via a web browser. The setup consists of three steps:
    1. Connect the EAP to the network
    2. Log into the EAP (via a wired/wireless connection)
    3. Change the default SSID
    This video is suitable for users with a small number (1-3) of EAPs .

    Scopri

FAQs

Firmware

Un aggiornamento firmware può risolvere problemi, aumentare le performance o introdurre nuove funzionalità.

Come aggiornare

  • È strettamente necessario verificare modello e versione hardware prima di scaricare ed installare ogni firmware.
  • È possibile installare solamente firmware creati per modello e versione hardware in uso.
  • Il caricamento di un firmware non appropriato può danneggiare irrimediabilmente il dispositivo e ne invalida la garanzia.
  • Assicurarsi di non interrompere l’alimentazione del dispositivo e del computer durante l’aggiornamento.
  • I firmware sono scaricabili esclusivamente in formato compresso: è necessario estrarre il firmware aprendo l’archivio compresso tramite un software di decompressione e salvandolo sul desktop.

 

 

EAP225-Outdoor(EU)_V1_5.0.3 Build 20210316

Download
Data di pubblicazione: 2021-04-27 Lingua: English Dimensioni file: 7.33 MB

This firmware fully adapts the Omada SDN platform and only compatible with Omada Controller v4.1.5 or above.

If you are using an old Omada controller and plan to upgrade this firmware for EAP, you must upgrade the Omada Controller as well: Upgrade Guide

EAP225-Outdoor(EU)_V1_1.20.0 Build 20200422

Download
Data di pubblicazione: 2020-07-06 Lingua: English Dimensioni file: 7.20 MB

This firmware is fully adapted Omada SDN platform but only compatible with Omada controller v4.1.5 or above.

If you are using old Omada controller and plan to upgrade firmware for EAP, then you must upgrade Omada controller as well, and please follow Upgrade Guide to upgrade Omada controller.

If your EAP is working standalone, please note that the EAP will be reset after upgrading to this firmware and you need to re-configure your EAP.

EAP225-Outdoor(EU)_V1_1.7.0 Build 20200113

Download
Data di pubblicazione: 2020-03-02 Lingua: English Dimensioni file: 7.76 MB

Recommended Controller Software Version: Omada Controller v3.2.6 or above

Codice Open Source (GPL)

I prodotti TP-LINK contengono software sviluppato da terze parti, incluso software distribuito con licenza GPL (GNU General Public Licence versione 1, 2 o 3) o con licenza LGPL (GNU Lesser General Public License): l'utilizzo di questo software è possibile entro limiti e condizioni stabiliti dalla tipologia di licenza con la quale è distribuito e specificate a questo link. È possibile ottenere il codice sorgente soggetto a GPL e la lista dei prodotti che utilizzano tale codice all'interno del Centro sorgenti GPL.

I relativi software sono distribuiti con formula di TOTALE ESCLUSIONE DI GARANZIA; non sono pertanto garantite COMMERCIABILITÀ e/o IDONEITÀ PER QUALSIASI UTILIZZO SPECIFICO.

Per ulteriori informazioni consultare il testo GNU General Public License.

Controller Software

The EAP Controller is used to manage multiple EAPs intensively.

Omada_SDN_Controller_V4.3.5_linux_x64.deb

Download
Data di pubblicazione: 2021-05-07 Lingua: English Dimensioni file: 59.39 MB
Sistema operativo: Ubuntu 14.04/16.04/17.04/18.04/Debian

If you are planning to upgrade from the old controller(v3.2.14 or below) to this version, please read the: Omada Controller Upgrade Guide 

Some new functions of the Controller require device firmware support, and the supporting firmware for routers and switches will be released soon.

Omada_Controller_V4.3.5_Windows

Download
Data di pubblicazione: 2021-04-27 Lingua: English Dimensioni file: 91.11 MB

New Omada SDN Firmware
 

Se si prevede di aggiornare dalla vecchia versione (v3.2.14 o precedente) alla versione SDN, leggere attentamente la seguente guida Omada Controller Upgrade Guide contenuta nel pacchetto di installazione prima di aggiornare il controller.

Alcune nuove funzionalità della nuova versione richiedono l'aggiornamento firmware anche dei dispositvi come Access Point, Switch e Gateway.

 

Supported device models and firmware:

EAP:

EAP110_V4 3.20.0 Build 20200525 Rel. 36899 and above

EAP115_V4 3.20.0 Build 20200525 Rel.36931 and above

EAP225_V3 2.20.0 Build 20200422 Rel. 70513 and above

EAP245_V3 2.20.0 Build 20200423 Rel. 36779 and above

EAP115-Wall_V1 1.20.0 Build 20200509 Rel. 63986 and above

EAP225-Wall_V2 1.20.0 Build 20200422 Rel. 70504 and above

EAP110-Outdoor_V3 3.20.0 Build 20200511 Rel. 33388 and above

EAP225-Outdoor_V1 1.20.0 Build 20200422 Rel. 70543 and above

EAP265 HD_V1, EAP230-Wall_V1, EAP235-Wall_V1, EAP660 HD_V1, EAP620 HD_V1

Switch:

TL_SG3428MP_V1, TL_SG3428_V1, TL-SG2210MP_V1, TL-SG2210P_V3.20, TL-SG2428P_V1, TL-SG2008P_V1, TL-SG2008_V3, TL-SG3428X_V1, TL_SG3428XMP_V1, TL-SG3210XHP-M2_V1, TL-SG3452P_V1, TL-SG3452_V1, TL-SG3428MP_V1, TL-SG3210_V3, TL-SG2218_V1, TL-SL2428P_V4.2

Gateway:

ER605_V1, ER7206_V1

 

New Feature/Enhancement:

1. Add AI-Roaming function.

2. Add daily/weekly/monthly limit in Voucher/Local User traffic limit function.

3. Add layer-3 function for L2+ switches.

4. Add IPv6 function.

5. Add daylight saving time function.

6. Portal supports multiple entries. Local user accounts and voucher codes support binding to different portal entries.

7. Add RADIUS DM function in portal RADIUS authentication.

8. Add dynamic VLAN feature in RADIUS profile.

9. Add rate limit templates for SSID and Client rate limit modules.

10. Add ethertype value for switch ACL.

11. Add Switch Status, Router Table, Dynamic DNS, VPN Status, Port Forwarding Status in the Insight list.

12. Optimize the configuration logic for Switch STP and loopback detection function.

13. Cancel the site administrator's authority for global configuration, such as controller general and maintenance settings.

14. Upgrade the MongoDB database version from 3.4.20 to 3.4.23.

 

Bug Fixed:

1. Fixed the bug that the local user can still access the Internet after re-authenticating, though it has reached the upper traffic limit.

2. Fixed the bug that the PoE scheduler may not take effect.

3. Fixed the bug that the Omada Controller frequently prints roaming logs in the log list.

4. Fixed the bug that the settings of PAP and CHAP authentication mode are inverse in the Controller.

5. Fixed the bug that we may not be able to configure or disable the portal authentication (with general error occurs) sometimes.

6. Fixed the bug that we can’t set VPN servers in different Controller sites in the meantime.

7. Fixed the bug that the SDN Controller does not support spaces character and Nordic script.

8. Fixed the bug that the Controller may not restore the backup file successfully if the backup file is too large (80MB or above).

9. Add L2TP/PPTP Interface in static routing function.

10. Add L2TP/PPTP WAN Interface in policy routing function.

 

Notes:

1. Omada SDN Controller can configure and manage only certain devices with supported firmware. You need to make sure your device is compatible with Omada SDN Controller.

2. If you are using Omada Controller and plan to upgrade to this version, please follow the procedure of the Omada Controller Upgrade Guide.

3. Once upgraded to this version of Omada Controller, you will be NOT able to downgrade to version 3.2.10 or below. 

4. This version of the controller is applied to the Omada APP of version 3.0.X or above.

Omada_Controller_V3.2.14_Windows64bit

Download
Data di pubblicazione: 2020-12-25 Lingua: English Dimensioni file: 124.47MB
Sistema operativo: Windows 7/8/10/Server

Omada_Controller_V3.2.14_Linux_x64.tar

Download
Data di pubblicazione: 2020-12-25 Lingua: English Dimensioni file: 125.65MB
Sistema operativo: Ubuntu 14.04/16.04/17.04/18.04, CentOS 6.x/7.x and Fedora 20 or above, Debian

Bundled Firmware:
EAP110_V1, EAP110_V2 EAP110_V4
EAP115_V1, EAP115_V2 EAP115_V4
EAP225_V1, EAP225_V2 EAP225_V3
EAP225-Outdoor_V1
EAP110-Outdoor_V1 EAP110-Outdoor_V3
EAP245_V1 EAP245_V3
EAP115-Wall_V1 (EAP115-Wall is suitable for EU version only)
EAP225-Wall_V2 
EAP320_V1 EAP320_V2
EAP330_V1 EAP330_V2

Bug Fixed:
1. Fixed the XSS attack vulnerability

Notes:
1. To use Omada Controller 3.2.X new features, you need to upgrade your EAP's firmware to the corresponding version.
2. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.
 

Omada_Controller_V3.2.14_Linux_x64.deb

Download
Data di pubblicazione: 2020-12-25 Lingua: English Dimensioni file: 99.43MB
Sistema operativo: Ubuntu 14.04/16.04/17.04/18.04/Debian

Bundled Firmware:
EAP110_V1, EAP110_V2 EAP110_V4
EAP115_V1, EAP115_V2 EAP115_V4
EAP225_V1, EAP225_V2 EAP225_V3
EAP225-Outdoor_V1
EAP110-Outdoor_V1 EAP110-Outdoor_V3
EAP245_V1 EAP245_V3
EAP115-Wall_V1 (EAP115-Wall is suitable for EU version only)
EAP225-Wall_V2 
EAP320_V1 EAP320_V2
EAP330_V1 EAP330_V2

Bug Fixed:
1. Fixed the XSS attack vulnerability

Notes:
1. To use Omada Controller 3.2.X new features, you need to upgrade your EAP's firmware to the corresponding version.
2. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

Omada_Controller_V3.2.14_Windows32bit

Download
Data di pubblicazione: 2020-12-25 Lingua: English Dimensioni file: 120.55MB
Sistema operativo: Windows 7/8/10/Server

Bundled Firmware:
EAP110_V1, EAP110_V2 EAP110_V4
EAP115_V1, EAP115_V2 EAP115_V4
EAP225_V1, EAP225_V2 EAP225_V3
EAP225-Outdoor_V1
EAP110-Outdoor_V1 EAP110-Outdoor_V3
EAP245_V1 EAP245_V3
EAP115-Wall_V1 (EAP115-Wall is suitable for EU version only)
EAP225-Wall_V2 
EAP320_V1 EAP320_V2
EAP330_V1 EAP330_V2

Bug Fixed:
1. Fixed the XSS attack vulnerability

Notes:
1. To use Omada Controller 3.2.X new features, you need to upgrade your EAP's firmware to the corresponding version.
2. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.
 

Omada Discovery Utility

Omada Discovery Utility 4.2.4

Download
Data di pubblicazione: 2020-11-09 Lingua: English Dimensioni file: 33.16 MB
Sistema operativo: Win2000/XP/2003/Vista/7/8/8.1/10/Mac/Linux

New Feature/Enhancement:

1. Support to discover the gateway and switch that support Omada SDN platform.

2. Add timeout mechanism during adopting the devices.

 

Note:

1. This version of software can be used in both Windows and Mac operation system.

2. Double click the software or run the command “java –jar **.jar” to run the software on MacOS (**.jar is the name of this software).

3. To run this software, you need to install JRE 8.0 on your PC first.

4. Omada Controller and Discover Utility cannot run on the same computer at the same time.

Emulator

Versione Firmware
Working Mode
Lingua
180411(EU)
-
English
T2700G-28TQ License Download
License Model: T2700G-28TQ-L1000

Find your product MAC and Serial Number.
License Key:
Product Serial Number:
Product MAC:
Checking code:

Iscriviti alla newsletter TP-Link prende la Privacy seriamente. Per maggiori informazioni sul trattamento dei tuoi dati consulta l'Informativa Privacy.

From United States?

Check products and services for your region.