Scarica per EAP110-Outdoor V3

Si prega di scegliere la versione hardware:

V3

>Come identificare modello e versione hardware di un prodotto TP-Link?

ATTENZIONE
Modelli e versioni variano a seconda dell'area geografica.
Per prodotti in uso in Italia, utilizzare solo risorse presenti sul sito
http://www.tp-link.it .
È strettamente necessario verificare modello e versione hardware prima di scaricare ed installare ogni firmware.
Product Overview
Documento

Setup Video

  • How to manage TP-Link EAPs centrally via the Software Controller

    This video demonstrates how to manage TP-Link EAPs centrally via the Software Controller. The setup consists of three steps:
    • Install the Software
    • Configure Discovery Utility (If your EAPs and the Controller Host are on different subnets)
    • Configure Software Controller

    THIS VIDEO APPLIES TO:
    • All TP-Link EAP models (except EAP120 and EAP220)
    • Omada Software Controller
    • Mass EAPs (usually more than three)

    Learn More

  • How to set up a TP Link EAP via your mobile phone

    This video demonstrates how to set up a TP-Link EAP via your mobile phone. The setup consists of four steps:
    • Connect the EAP to the network
    • Download the Omada APP
    • Connect to the EAP's wireless network
    • Set up the EAP using the Omada APP

    THIS VIDEO APPLIES TO:
    • All TP-Link EAP models. (except EAP120 and EAP220)
    • A small number (1-3) of EAPs.

    Learn More

  • How to setup the OC200 via a web browser

    This video will demonstrate how to set up the OC200 via a web browser. The setup consists of six steps:
    • Connect the OC200 to your local network.
    • Get ready for setup.
    • Create a TP-Link ID.
    • Log into your TP-Link ID.
    • Add the OC200 to your TP-Link ID.
    • Follow the wizard to set up the OC200.

    THIS VIDEO APPLIES TO:
    • All TP-Link EAP models (except EAP120 and EAP220)
    • Omada Cloud Controller OC200
    • Mass EAPs (usually more than three)

    Learn More

  • How to setup the OC200 via your mobile phone

    This video will demonstrate how to set up the OC200 via your mobile phone. You need to use the Omada APP to complete the setup. The setup consists of six steps:
    • Connect the OC200 to your local network.
    • Get ready for setup.
    • Create a TP-Link ID.
    • Log into your TP-Link ID.
    • Add the OC200 to your TP-Link ID.
    • Follow the wizard to set up the OC200.
    THIS VIDEO APPLIES TO:
    • All TP-Link EAP models (except EAP120 and EAP220)
    • Omada Cloud Controller OC200
    • Mass EAPs (usually more than three)

    Learn More

  • How to manage TP-Link EAPs centrally from a remote place via a web browser

    You can manage TP-Link EAPs at any time from anywhere with the Cloud Access function of our Omada Controller Software. This video introduces both the application scenario and concrete steps you can follow. Don't hesitate to give it a try.
    THIS VIDEO APPLIES TO:
    • All TP-Link EAP models (except EAP120 and EAP220)
    • Omada Controller Software (version 3.0.2 or above)
    • Mass EAPs (usually more than three)

    Learn More

  • A Quick Overview of EAP Management Methods

    This video introduces how to choose the optimum method to manage TP-Link EAPs in your scenario.
    Here are 3 most common scenarios and their corresponding methods:
    • Manage 1 or 2 EAPs locally
    • Manage 3 or more EAPs locally
    • Manage 3 or more EAPs remotely
    When choosing the method, consider the following questions:
    1. Standalone Mode or Controller Mode?
    2. In Controller mode, what kind of controller will you use, an OC200 or a PC with Omada Software Controller?
    3. What kind of user interface will you use, a web browser or the Omada app?

    Learn More

  • How to Set up a TP-Link EAP via Web browser

    This video will demonstrate how to set up a TP-Link EAP via a web browser. The setup consists of three steps:
    1. Connect the EAP to the network
    2. Log into the EAP (via a wired/wireless connection)
    3. Change the default SSID
    This video is suitable for users with a small number (1-3) of EAPs .

    Learn More

FAQs

Firmware

Un aggiornamento firmware può risolvere problemi, aumentare le performance o introdurre nuove funzionalità.

Come aggiornare

  • È strettamente necessario verificare modello e versione hardware prima di scaricare ed installare ogni firmware.
  • È possibile installare solamente firmware creati per modello e versione hardware in uso.
  • Il caricamento di un firmware non appropriato può danneggiare irrimediabilmente il dispositivo e ne invalida la garanzia.
  • Assicurarsi di non interrompere l’alimentazione del dispositivo e del computer durante l’aggiornamento.
  • I firmware sono scaricabili esclusivamente in formato compresso: è necessario estrarre il firmware aprendo l’archivio compresso tramite un software di decompressione e salvandolo sul desktop.

 

 

EAP110-Outdoor(EU)_V3_3.5.0 Build 20200113
Data di pubblicazione: 2020-03-04 Lingua: English Dimensioni file: 5.91 MB

Recommended Controller Software Version: Omada Controller v3.2.6 or above

 

New Feature/Enhancement:

1. Change the mechanism that the IP configuration in Standalone mode will be retained after the EAP is adopted by the Controller.

2. Add anti-brute force cracking mechanism that you cannot login to the EAP via SSH or webserver in two hours if you fail to login up to 30 times in half an hour.

3. Optimize NTP server to support domain name.

4. Change the “Term of Service” of portal settings page in standalone mode as unchecked by default.

5. Optimize the UI of SSID and Free Authentication Policy in Standalone mode.

6. Optimize the DNS resolution process of EAP to avoid parsing wrong IP.

7. Reduce the time interval to 5s and limit the size to 2k bytes of the More Client Detail Log in Log Settings.

8. Change the OpenSSL version to 1.0.2q.

9. Optimize UI, including character optimization and display error correction.

10. Update the time zone of Caracas from GMT-4:30 to GMT-4:00.

 

Bug Fixed:

1. Fixed the bug that client devices can pass the portal authentication after disconnected from the Controller.

2. Fixed the bug that untagged packets can be transferred to SSIDs with different VLANs.

3. Fixed the bug that packets with VLAN tag can be forwarded to the SSID without wireless VLAN setting.

4. Fixed the bug that External Radius Server portal page may not pop up in some clients.

5. Fixed the bug that when adding an SSID with no password and change the encryption mode to WPA on Omada APP, the clients can still connect to the SSID without password.

6. Fixed the bug that the management page may not be accessed after EAP is disconnected from the Controller.

7. Fixed the bug that when APs are disconnected from Controller, the rate limit configuration will not be issued to these APs after they are back to connected again.

8. Fixed the bug that the EAP may hang after clicking save in wireless VLAN page in Standalone mode.

9. Fixed the bug that the EAP may hang if scanning rogue AP in high frequency.

10. Fixed the bug that when the time of EAP is synchronized with PC, it will be the same as PC’s time not considering different time zones.

 

Notes:

1. For EAP110-Outdoor v3 only.

2. Your device's configuration won't be lost after upgrading.

3. This version of firmware is applied to Omada APP of version 2.1.X or above.

4. You cannot downgrade if you upgrade from the firmware released in 2018 or earlier to this version directly.

EAP110-Outdoor(EU)_V3_3.0.0 Build 20171127
Data di pubblicazione: 2017-12-21 Lingua: English Dimensioni file: 6.88 MB

Recommended Controller Software Version: Omada Controller v 2.5.x

New Features/Improvements:

1. First firmware released for EAP110-Outdoor_V3.

2. Facebook Portal Authentication, SMS Portal Authentication and Local User Authentication support for EAP110-Outdoor_V3 when managed by Omada Controller.

 

Bug Fixed:

1. EAP will reboot when XiaoMi/Samsung phones connect to the Portal network.

2. Only three Predefine Country are available to be selected under the Daylight Saving.

3. Failed redirection of portal authentication page after changing the default HTTP port of Omada Controller.

Notes:

1. For EAP110-Outdoor_V3

2. Your device's configuration won't be lost after upgrading

Codice Open Source (GPL)

I prodotti TP-LINK contengono software sviluppato da terze parti, incluso software distribuito con licenza GPL (GNU General Public Licence versione 1, 2 o 3) o con licenza LGPL (GNU Lesser General Public License): l'utilizzo di questo software è possibile entro limiti e condizioni stabiliti dalla tipologia di licenza con la quale è distribuito e specificate a questo link. È possibile ottenere il codice sorgente soggetto a GPL e la lista dei prodotti che utilizzano tale codice all'interno del Centro sorgenti GPL.

I relativi software sono distribuiti con formula di TOTALE ESCLUSIONE DI GARANZIA; non sono pertanto garantite COMMERCIABILITÀ e/o IDONEITÀ PER QUALSIASI UTILIZZO SPECIFICO.

Per ulteriori informazioni consultare il testo GNU General Public License.

Controller Software

The EAP Controller is used to manage multiple EAPs intensively.

Data di pubblicazione: 2020-04-20 Lingua: English Dimensioni file: 120.54MB
Sistema operativo: Windows 7/8/10/Server

New Feature/Enhancement:

1. Added the feature that the system logs can be exported.

2. Changed the priority that non-administrator role cannot change the history data retention settings.

3. Optimized the UI of Statistics in Omada Controller.

 

Bug Fixed:

1. Fixed the bug that the External Web Portal cannot authenticate successfully if the SSID of this portal has special characters.

2. Fixed the bug that the Cloud Access cannot be displayed normally in the low version of Firefox.

3. Fixed the bug that Omada Controller allow any user to read the files of controller.

4. Fixed the bug that controller will report an error when Top Usage data is empty.

 

Notes:

1. To use Omada Controller 3.2.X new features, you need to upgrade your EAP's firmware to the corresponding version.

2. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

3. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.X or earlier version.

Data di pubblicazione: 2020-04-20 Lingua: English Dimensioni file: 124.46MB
Sistema operativo: Windows 7/8/10/Server

New Feature/Enhancement:

1. Added the feature that the system logs can be exported.

2. Changed the priority that non-administrator role cannot change the history data retention settings.

3. Optimized the UI of Statistics in Omada Controller.

 

Bug Fixed:

1. Fixed the bug that the External Web Portal cannot authenticate successfully if the SSID of this portal has special characters.

2. Fixed the bug that the Cloud Access cannot be displayed normally in the low version of Firefox.

3. Fixed the bug that Omada Controller allow any user to read the files of controller.

4. Fixed the bug that controller will report an error when Top Usage data is empty.

 

Notes:

1. To use Omada Controller 3.2.X new features, you need to upgrade your EAP's firmware to the corresponding version.

2. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

3. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.X or earlier version.

EAP Discovery Tool

The EAP Discovery Tool can help the EAP Controller to adopt the EAP in L3 Network, and you can also use the EAP Discovery Tool to find the EAP’s IP address.

Data di pubblicazione: 2019-08-06 Lingua: English Dimensioni file: 25.85 MB
Sistema operativo: WinXP/Vista/7/8/8.1/10/Server2008/Server2012/Mac OS X 10.7/10.8/10.9/10.10/10.11

Bug fixed:

1. Fixed the bug that the Discovery Utility may fail to find EAPs.

2. Fixed the bug that the Cancel button may overlap with the display box after managing APs.

 

Note:

1. This version of software can be used in both Windows and Mac operation system.

2. Double click the software or run the command “java –jar **.jar” to run the software on MacOS (**.jar is the name of this software).

3. To run this software, you need to install JRE 8.0 on your PC first.

Emulator

Versione Firmware
Working Mode
Lingua
180418(EU)
-
English
T2700G-28TQ License Download
License Model: T2700G-28TQ-L1000

Find your product MAC and Serial Number.
License Key:
Product Serial Number:
Product MAC:
Checking code:

Iscriviti alla newsletter TP-Link prende la Privacy seriamente. Per maggiori informazioni sul trattamento dei tuoi dati consulta l'Informativa Privacy.