Click to skip the navigation bar

How to Set Up a TP-Link DSL Modem Router Using the Tether App (Classic Interface)

Configuration Guide
Last updated: November 18, 2026

This guide shows you how to set up a compatible TP-Link DSL modem router using the Tether app, whether your internet service arrives through a DSL phone line or an Ethernet cable. (Applicable Models: Archer VR400 V1 V2 V3, Archer VR2100, Archer VR300, etc.)

If your router model is Archer VR400 V4 or Archer VX1800v, refer to this guide instead:

How to Set Up a TP-Link DSL Modem Router Using the Tether App (New Interface)

If you prefer to set up the router via the Web Management Page, refer to this guide instead:

How to Set Up a TP-Link DSL Modem Router via the Web Management Page (Classic Interface)

Key Takeaways

  • Choose DSL Modem Router Mode for a DSL phone line or Wireless Router Mode for an Ethernet internet connection.
  • Confirm your ISP’s connection type and any required PPPoE credentials, VLAN ID, or DSL type (VDSL or ADSL) before setup.
  • Check your model and hardware version, then follow the matching setup section.
  • Apply your settings, reconnect to Wi-Fi if needed, and open a website to confirm internet access.

Before You Begin

1. Check the model and hardware version on the router’s label.

2. Ensure your router supports the Tether app: Tether App Compatible Networking Devices.

3. Identify Your Internet Cable and Determine the Correct Operation Mode.

A DSL modem router combines a DSL modem and a Wi-Fi router. Choose its operation mode based on the cable that brings internet service into the router:

  • DSL phone cable (RJ11): Connect it to the smaller port labeled DSL. Use DSL Modem Router Mode. If your ISP requires a splitter or filter, connect it as instructed by your ISP.
  • Ethernet cable (RJ45): Connect it to the larger port labeled LAN4/WAN. Use Wireless Router Mode. Connect the other end to your existing modem, fiber terminal/ONT, main router, or internet-enabled wall outlet.

For help identifying the connectors, see RJ11 vs. RJ45.

A smaller RJ11 DSL phone connector and a larger RJ45 Ethernet cable connector.

4. Gather Information from Your ISP.

Contact your Internet Service Provider (ISP) for the following:

1) Internet Connection Type:

  • Dynamic IP: Typically requires no credentials.
  • PPPoE: Requires a specific username and password provided by your ISP.
  • Static IP: Requires a fixed IP address, Subnet Mask, Gateway, and DNS servers.

2) VLAN ID: Required by certain ISPs.

3) DSL Modulation Type (if using DSL): VDSL or ADSL.

Step-by-Step Guide

Guide for Setting DSL Modem Router Mode (Default Mode)

Step 1. Access the Router

Connect your phone to the router’s Wi-Fi. You can find the default Wi-Fi name (e.g., TP-Link_xxxx) on the router’s label.

Open the Tether app, tap your router under Devices to begin setup.

Step 2. Confirm the DSL connection

Follow the wiring screen and make sure the phone line is connected to the DSL port.

Setup diagram showing the router connected to a DSL phone line.

Step 3. Create a Device Login Password

Set an administrator password (1 to 15 characters) to manage your router, then tap Next.

Tether app screen for creating a device password during initial setup.

Step 4. Select Your ISP and DSL Service

Choose your region and ISP. If your ISP is not listed, select Other. Select ADSL or VDSL as confirmed by your ISP.

ISP selection screen showing country or region and the Other option.Tether app screen for selecting ADSL or VDSL service.

Step 5. Configure the Internet Connection

Select the internet connection type, enter your ISP credentials, and enter the VLAN ID if required, then tap Next.

DSL internet settings screen with connection type and VLAN options.

Step 6. Set Up Wi-Fi and Apply the Settings

Customize the Wi-Fi name and password. If you want the 2.4 GHz and 5 GHz Wi-Fi names and passwords to be the same, turn on Smart Connect. If it is turned off, configure each band separately as needed. Tap Next. Review the settings and tap Apply.

Enter a Wi-Fi network name and password.Review the device, internet, and Wi-Fi settings before applying them.

Step 7. Test the Internet and Finish Setup

Wait 1-2 minutes for the new Wi-Fi to activate. Reconnect to the new Wi-Fi in your phone's Wi-Fi list, then return to the Tether App. Wait for Tether to test the internet connection. If the test succeeds, tap Finish.

If the test fails, double-check your cable connection, operation mode, and ISP credentials.

Wait while Tether tests the internet connection.Tap Finish after the internet connection test succeeds.

Guide for Setting Wireless Router Mode

Note: The classic Tether setup wizard defaults to DSL setup. If you are using an Ethernet cable (Wireless Router Mode), please complete the initial setup steps with placeholder settings, skip the internet test when it fails, and then switch the router to Wireless Router Mode.

Step 1. Access the Router

Connect your phone to the router’s Wi-Fi. You can find the default Wi-Fi name (e.g., TP-Link_xxxx) on the router’s label (To ensure the router can be detected, do not connect the Ethernet cable to the LAN4/WAN port of the router until the router has been switched to Wireless Router Mode).

Open the Tether app, tap your router under Devices to begin setup.

Step 2. Confirm the DSL connection.

Ignore the DSL wiring screen.

Setup diagram showing the router connected to a DSL phone line.

Step 3. Create a Device Login Password

Set an administrator password (1 to 15 characters) to manage your router, then tap Next.

Tether app screen for creating a device password during initial setup.

Step 4. Select your ISP and DSL Service

Choose your region and select ISP as Other. Select VDSL connection type.

ISP selection screen showing country or region and the Other option.Tether app screen for selecting ADSL or VDSL service.

Step 5. Configure the Internet Connection

Select the internet connection type as Dynamic IP, and disable the VLAN ID, then tap Next.

DSL internet settings screen with connection type and VLAN options.

Step 6. Set Up Wi-Fi and Apply the Settings

Customize the Wi-Fi name and password. If you want the 2.4 GHz and 5 GHz Wi-Fi names and passwords to be the same, turn on Smart Connect. If it's off, configure each band separately as needed. Tap Next. Review the settings and tap Apply.

Enter a Wi-Fi network name and password.Review the device, internet, and Wi-Fi settings before applying them.

Step 7. Test the Internet and Skip the Setup

Wait 1-2 minutes for the new Wi-Fi to activate. Reconnect to the new Wi-Fi in your phone's Wi-Fi list, then return to the Tether App.

Wait for Tether to test the connection. Because the DSL port is not connected, the network test at the end will show "Unable to connect to the internet". This is completely normal. Tap Skip this step at the bottom.

Failed internet test screen with Skip this step highlighted.

Step 8. Switch to Wireless Router Mode

Go to More > Operation Mode, select Wireless Router, and tap Apply. Confirm the restart if prompted.

Wait for the router to restart. Reconnect your phone to its Wi-Fi and reopen Tether.

Locate Operation Mode screen with Wireless Router selected.Locate confirmation dialog asking to restart the router after changing operation mode.

Step 9. Configure the Ethernet Internet Connection

Connect the Ethernet cable to the LAN4/WAN port of the router.

Go to More > Internet Connection, tap IPv4 Connection, and select Dynamic IP, PPPoE, or Static IP as required.

Locate More menu with Internet Connection highlighted.Locate Internet Connection page with the connection settings entry highlighted.Locate list of Dynamic IP, PPPoE, and Static IP connection types.

Step 10. Set the VLAN ID (If Required)

Return to the Internet Connection page, tap VLAN, enable it only if your ISP requires tagging, and enter its VLAN ID. Tap Save and save any other changes when prompted.

Locate Internet Connection page with the VLAN settings entry highlighted.Locate VLAN settings screen with VLAN enabled and the Save button highlighted.

Step 11. Verify Internet Connectivity

Wait 3 to 5 minutes for the router to negotiate the connection with your ISP.

Check the physical Internet LED on the front panel:

  • Solid White / Green: Connected successfully to the Internet.
  • Orange / Off: No Internet connection. Double-check your cable connection, operation mode, and ISP credentials.

Related FAQs

Looking For More

Is this faq useful?

Your feedback helps improve this site.

This Article Applies to:

Setup Videos

What should I do if I cannot access the internet? - Using a DSL modem and a TP-Link router

How to configure the wireless router mode for TP Link DSL modem router

Community

TP-Link Community

Still need help? Search for answers, ask questions, and get help from TP-Link experts and other users around the world.

Visit the Community >