-
Otthon
Routerek
Gyors és megbízható Wi-Fi hálózat létrehozásához
Hálózatkiterjesztés
Könnyedén növelje meg, és tegye jobbá hálózatát
SOHO Switches (Kapcsolók)
Ha több vezetékes kapcsolatra van szüksége otthonában
Egyéb eszközök
Amire még szüksége lehet a kapcsolattartáshoz
-
Intelligens otthon
Kamerák
Tartsa szemmel ami fontos
Wi-Fi-s konnektor
Tegye otthoni eszközeit okosabbá
Wi-Fi-s LED izzók
Fény, minden alkalomra
-
Irodai/üzleti
JetStream Switch
High-Speed wired networking from L3 managed to unmanaged
Omada szoftver kontrolleres AP-k
Professional business Wi-Fi with centralized management
SafeStream Router
Secure VPN and Load Balance gateways to the business
VIGI Surveillance
VIGI video surveillance is dedicated to your security
Pharos Vezeték nélküli szélessáv
Ideal for long range wireless broadband networking
-
Szolgáltatóknak
DSL
Capable of high-speed network and integrated broadband applications
LTE/3G
Gondoskodik az internet hozzáférésről, bárhol is legyen.
PON
The leading technology for delivering gigabit Internet services
Áramköri jeltovábbító
Átalakítja az áramkört belső/külső hálózat részévé.
Range Extender
Easily expand your Wi-Fi coverage.
Switch-ek
Növelje hálózatát kiváló teljesítménnyel.
Üzleti Wi-FI megoldások
A vállalkozás vezeték nélküli hálózatát új szintre emeli.
How to Setup IPSec Tunnel (VPN) on TD-W8960N/TD-W8950ND/TD-W8968(V3 V4)
This article illustrates a configuration instance for building an IPSec VPN tunnel between two units of TD-W8960N/TD-W8950ND/TD-W8968(V3).
IPSec tunnel is usually built to connect two or more remote LANs via Internet so that hosts in different remote LANs are able to communicate with each other as if they are all in the same LAN. For more details about VPN tunnel please refer to Wikipedia.
Figure 1 Configuration Instance
Here are step by step instructions for your reference (the following steps are based on Figure 1):
Configuration on Site A
1. Login to the management page of TD-W8960N/TD-W8950ND/TD-W8968(V3). If you are not sure how to enter the management page, please click here for details.
2. On the left menu of the management page, please click Advanced Setup and then click IPSec.
3. On the IPSec main page, please click Add New Connection.
4. On the IPSec configuration page, please do configuration as follows:
IPSec Connection Name: Define a name for this connection;
Remote IPSec Gateway Address: Input he WAN IP address of site B;
Site A
Tunnel access from local IP addresses: For a whole LAN please select Subnet; for a single host please select Single Address. In this instance we select Subnet;
IP Address for VPN: Input the LAN IP range of site A. In this instance, we should input 192.168.1.0;
IP Subnetmask: Input the LAN subnet mask of site A. In this instance, we should input 255.255.255.0;
Site B
Tunnel access from remote IP addresses: For a whole LAN please select Subnet; for a single host please select Single Address. In this instance we select Subnet;
IP Address for VPN: Input the LAN IP range of site B. In this instance, we should input 192.168.2.0;
IP Subnetmask: Input the LAN subnet mask of site B. In this instance, we should input 255.255.255.0;
5. Leave other settings as the default value and click Save/Apply.
Configuration on Site B
1. Log onto the management page of TD-W8960N/TD-W8950ND/TD-W8968(V3).
2. On the left menu of the management page, please click Advanced Setup and then click IPSec.
3. On the IPSec main page, please click Add New Connection.
4. On the IPSec configuration page, please do configuration as follows:
IPSec Connection Name: Define a name for this connection;
Remote IPSec Gateway Address: Input he WAN IP address of site B;
Site A
Tunnel access from local IP addresses: For a whole LAN please select Subnet; for a single host please select Single Address. In this instance we select Subnet;
IP Address for VPN: Input the LAN IP range of site B. In this instance, we should input 192.168.2.0;
IP Subnetmask: Input the LAN subnet mask of site B. In this instance, we should input 255.255.255.0;
Site B
Tunnel access from remote IP addresses: For a whole LAN please select Subnet; for a single host please select Single Address. In this instance we select Subnet;
IP Address for VPN: Input the LAN IP range of site A. In this instance, we should input 192.168.1.0;
IP Subnetmask: Input the LAN subnet mask of site A. In this instance, we should input 255.255.255.0;
5. Leave other settings as the default value and click Save/Apply.
Check the IPSec Connection
1. On the host in LAN1, press [Windows Logo] + [R] to open Run dialog. Input “cmd” and hit OK.
2. In the CLI window, type in “ping 192.168.2.x” (“192.168.2.x” can be IP address of any host in LAN2). Then press [Enter].
If Ping proceeds successfully (gets replies from host in LAN2), the IPSec connection must be working properly now.
Here until, all basic configuration required for an IPSec tunnel is completed. If one of the site has been off line for a while, for example, if Site A has been disconnected, on Site B you need to click Disable and then click Enable after Site A back on line in order to re-establish the IPSec tunnel.
If there are any further problems, please click here to contact TP-Link technical support.
Get to know more details of each function and configuration please go to Download Center to download the manual of your product.
Véleménye segíti az oldal fejlesztését