-
Hogar
SOHO Switches
Manteniendo el hogar conectado para conexiones de calidad
Accesorios
Todo lo demás que necesitas para un estilo de vida conectado
-
Hogar Inteligente
Enchufes Inteligentes
Mejora tus dispositivos domésticos
Cámaras de Seguridad
Vigilando lo que importa
Bombillas Inteligentes
Luz para cada ocasión
Extensor de Cobertura+
Extienda el Wi-Fi y administre con la aplicación Kasa
-
Empresa
Switches
Redes cableadas de alta velocidad desde gestión L3 a switches sin gestión
Omada Cloud SDN
La solución en la nube más inteligente para redes empresariales
Banda Ancha Inalámbrica Pharos
Ideal para redes de banda ancha inalámbrica de largo alcance
Routers SafeStream
VPN segura y puertas de enlace de equilibrio de carga para el negocio
-
Proveedor de Servicios
DSL
Capaz de red de alta velocidad y aplicaciones integradas de banda ancha
Wi-Fi Router
La elección fiable para redes domésticas
LTE/3G
Mantiene el acceso a Internet donde quiera que vaya.
PON
La tecnología líder para brindar servicios de Internet gigabit
Adaptadores Powerline
Transforma el cableado eléctrico para llevar la señal de red.
Range Extender
Amplía fácilmente la cobertura de Wi-Fi.
Switches
Aumenta la red de su empresa con un rendimiento de primera calidad.
Wi-Fi Empresarial
Lleve su red Wi-Fi empresarial a nuevos niveles.
How to configure Static Routing on wireless routers?
Overview:
A static route is a pre-determined path that network information must follow to reach a specific host or network.
Here are two typical scenarios, as examples of when a static route is needed, consider the following case.
Scenario 1:
Issue: The gateway of PC is router2 which connected the Internet, but when PC visit servers in intranet, firstly the request will be sent to router2. Because there is no route to server1 and server2 on route table of router2, thus the request will be thrown away.
Resolution: Therefore, if you want PC to visit servers in intranet, you have to set up a static route on router2 helps your packet route to router1.
Net parameter:Servers in net segment: 172.30.30.0. IP subnet mask for this net segment is 255.255.255.0
Scenario 2:
Issue: The gateway of LAN network is router 1, and router2 WDS router1’s signal.
But there is no route record from router2 to NTP server on route table of router2, therefore, router2 can’t get synchronization time from server.
Resolution: In order to solving the issue, you have to set up a static route on router2.
Net parameter:The IP of Server in Internet is 132.163.4.101. IP subnet mask for this address is 255.255.255.255
Steps of Configurations:
Step 1
Login configure page of router.
According to scenario 1 and scenario 2: type 192.168.0.1 in address bar,
Step 2
Type the username and password in the login page. The default username and password are both admin in lower case.
Step 3
Click Advanced Routing button on the left side of the screen, then select Static Routing List(in 54Mbps Wireless Router, the name of button is Static Routing).
Refer to picture:
And the page of Static Routing would appear on the screen:
Step 4
Click Add New….
Input destination network, subnet mask, default gateway, select status and save it.
Please refer to following introduction to input parameter.
Introduction:
In 1st bar, type the IP address of destination.
In 2ndbar, type the IP subnet mask for this destination.
In 3rdbar, type the gateway IP address, that must be on the same LAN segment as the router.
As per scenario 1, for net segment
As per scenario 2, for single IP address
If there are any further problems, please contact TP-Link Support.
Get to know more details of each function and configuration please go to Download Center to download the manual of your product.
Sus comentarios nos ayudan a mejorar este sitio.