Setup Video

  • How to setup the Omada Hardware Controller (OC200/OC300) via web browser

    This video will demonstrate how to set up OC200/OC300 via web browser. The setup consists of four steps: • Connect the controller to your local network. • Log in with your TP-Link ID. • Add the controller to your TP-Link ID. • Set up the controller THIS VIDEO APPLIES TO: • All TP-Link EAP models (except EAP120 and EAP220) • Omada Hardware Controller (OC200/OC300) • Mass EAPs (usually more than three)

    Learn More

  • How to setup the Omada Hardware Controller (OC200/OC300) via your mobile phone

    This video will demonstrate how to set up OC200/OC300 via your mobile phone. The setup consists of four steps: • Connect the controller to your local network. • Log in with your TP-Link ID. • Add the controller to your TP-Link ID. • Set up the controller THIS VIDEO APPLIES TO: • All TP-Link EAP models (except EAP120 and EAP220) • Omada Hardware Controller (OC200/OC300) • Mass EAPs (usually more than three)

    Learn More

Firmware

A firmware update can resolve issues that the previous firmware version may have and improve its current performance.

To Upgrade

IMPORTANT: To prevent upgrade failures, please read the following before proceeding with the upgrade process

  • Please upgrade firmware from the local TP-Link official website of the purchase location for your TP-Link device, otherwise it will be against the warranty. Please click here to change site if necessary.
  • Please verify the hardware version of your device for the firmware version. Wrong firmware upgrade may damage your device and void the warranty. (Normally V1.x=V1)
    How to find the hardware version on a TP-Link device?
  • Do NOT turn off the power during the upgrade process, as it may cause permanent damage to the product.
  • To avoid wireless disconnect issue during firmware upgrade process, it's recommended to upload firmware with wired connection unless there is no LAN/Ethernet port on your TP-Link device.
  • It's recommended that users stop all Internet applications on the computer, or simply disconnect Internet line from the device before the upgrade.
  • Use decompression software such as WinZIP or WinRAR to extract the file you download before the upgrade.
OC300(UN)_V1_1.1.0 Build 20210406
Published Date: 2021-04-28 Language: English File Size: 120.33MB

Build-in Omada SDN Controller v4.3.5

If you are planning to upgrade from the old controller(v3.2.14 or below) to this version, please read the Omada Controller Upgrade Guide in the installation package before upgrading the controller.

Some new functions of the Controller require device firmware support, and the supporting firmware for routers and switches will be released soon.

 

Supported device models and firmware:

EAP:

EAP110_V4 3.20.0 Build 20200525 Rel. 36899 and above

EAP115_V4 3.20.0 Build 20200525 Rel.36931 and above

EAP225_V3 2.20.0 Build 20200422 Rel. 70513 and above

EAP245_V3 2.20.0 Build 20200423 Rel. 36779 and above

EAP115-Wall_V1 1.20.0 Build 20200509 Rel. 63986 and above

EAP225-Wall_V2 1.20.0 Build 20200422 Rel. 70504 and above

EAP110-Outdoor_V3 3.20.0 Build 20200511 Rel. 33388 and above

EAP225-Outdoor_V1 1.20.0 Build 20200422 Rel. 70543 and above

EAP265 HD, EAP230-Wall, EAP235-Wall, EAP660 HD, EAP620 HD

Switch:

TL_SG3428MP, TL_SG3428, SG3428X, TL_SG3428XMP, TL-SG3452P, TL-SG3452,

TL-SG3210XHP-M2, TL-SG3210_V3, TL-SX3008F,

TL-SG2428P, TL-SL2428P_V4.2, TL-SG2210MP, TL-SG2210P_V3.20, TL-SG2218,

TL-SG2008P, TL-SG2008

Gateway:

ER605, ER7206

 

New Feature/Enhancement:

1. Add daylight saving time function.

2. Portal supports multiple entries. Local user accounts and voucher codes support binding to different portal entries.

3. Add daily/weekly/monthly limit in Voucher/Local User traffic limit function.

4. Add rate limit templates for SSID and Client rate limit modules.

5. Cancel the site administrator's authority for global configuration, such as controller general and maintenance settings.

6. Upgrade the MongoDB database version from 3.4.20 to 3.4.23.

For Router:

7. Add IPv6 function.

8. Add L2TP/PPTP interface in the static routing and policy routing function.

9. Add Firewall-State timeout at Settings-Network Security.

10. Add Router Table, Dynamic DNS, VPN Status, Port Forwarding Status in the Insight list.

11. Add ISP Load card and VPNs card in the Dashboard.

For Switch:

12. Add layer-3 function for L2+ switches.

13. Add ethertype value for switch ACL.

14. Add Switch Status in the Insight list.

15. Optimize the configuration logic for Switch STP and loopback detection function.

16. Add PoE utilization card in the Dashboard.

17. Add switch S/N information at Devices-Details-Overview

For EAP:

18. Add AI-Roaming function.

19. Add RADIUS DM function in portal RADIUS authentication.

20. Add dynamic VLAN feature in RADIUS profile.

21. Add OFDMA switch button for AX EAP.

 

Bug Fixed:

1. Fixed the bug that the local user can still access the Internet after re-authenticating, though it has reached the upper traffic limit.

2. Fixed the bug that the PoE scheduler may not take effect.

3. Fixed the bug that the Omada Controller frequently prints roaming logs in the log list.

4. Fixed the bug that the settings of PAP and CHAP authentication mode are inverse in the Controller.

5. Fixed the bug that we may not be able to configure or disable the portal authentication (with general error occurs) sometimes.

6. Fixed the bug that we can’t set VPN servers in different Controller sites in the meantime.

7. Fixed the bug that the SDN Controller does not support spaces character and Nordic script.

8. Fixed the bug that the Controller may not restore the backup file successfully if the backup file is too large (80MB or above).

 

Notes:

1. For OC300 (UN) V1 Only.

2. Omada SDN Controller can configure and manage only certain devices with supported firmware. You need to make sure your device is compatible with Omada SDN Controller.

3. Once upgraded to this version of Omada Controller, you will be NOT able to downgrade to version 3.2.14 or below. 

4. This version of the controller is applied to the Omada APP of version 3.0.x or above.

 

OC300(UN)_V1_1.0.4 Build 20210118
Published Date: 2021-03-03 Language: English File Size: 119.38MB

Built-in Omada SDN controller v4.2.11.

If you are planning to upgrade from the old controller(v3.2.10 or below) to this version, please read the Omada Controller Upgrade Guide in the installation package before upgrading the controller.

 

Supported device models and firmware:

EAP:

EAP110_V4 3.20.0 Build 20200525 Rel. 36899 and above

EAP115_V4 3.20.0 Build 20200525 Rel.36931 and above

EAP225_V3 2.20.0 Build 20200422 Rel. 70513 and above

EAP245_V3 2.20.0 Build 20200423 Rel. 36779 and above

EAP115-Wall_V1 1.20.0 Build 20200509 Rel. 63986 and above

EAP225-Wall_V2 1.20.0 Build 20200422 Rel. 70504 and above

EAP110-Outdoor_V3 3.20.0 Build 20200511 Rel. 33388 and above

EAP225-Outdoor_V1 1.20.0 Build 20200422 Rel. 70543 and above

EAP265 HD_V1, EAP230-Wall_V1, EAP235-Wall_V1, EAP660 HD_V1, EAP620 HD_V1

Switch:

TL_SG3428MP_V1, TL_SG3428_V1, TL-SG2210MP_V1, TL-SG2210P_V3.20, TL-SG2428P_V1, TL-SG2008P_V1, TL-SG2008_V3, TL-SG3428X_V1, TL_SG3428XMP_V1, TL-SG3210XHP-M2_V1, TL-SG3452P_V1, TL-SG3452_V1, TL-SG3428MP_V1, TL-SG3210_V3, TL-SG2218_V1, TL-SL2428P_V4.2

Gateway:

TL-R605_V1, TL-ER7206_V1

 

Bug Fixed:

1. Fixed the bug that we may not be able to export the XLSX file in Settings->Services->Export Data.

2. Fixed the bug that the OC300 may get an “Invalid Controller” error in the Cloud Access function if the OC300 didn’t connect to the Internet during the Quick Setup.

3. Fixed the bug that the IPSec and L2TP over IPSec VPN cannot be set on the same WAN port at the same time.

4. Fixed the bug that the speedtest in the dashboard may display general error and internet Capacity and Gateway are still displayed as N/A.

5. Fixed the bug that we may not be able to re-adopt the Mesh AP if we failed to adopt it with the wrong password for the first time.

6. Fixed the bug that the wireless client will be displayed as a wired client (LAN) on the controller.

7. Fixed the bug that the controller's band steering range is inconsistent with the actual supported range of EAP, resulting in the configuration not taking effect.

8. Fixed the bug that the wired clients that have passed portal authentication may display 0 traffic data in the Authorized Clients list.

9. Fixed the bug that the wired clients that have passed portal authentication may have lower traffic statistics.

10. Fixed the bug that the Controller may show a general error if we forget an EAP and then delete an SSID.

11. Fixed the bug that the wired clients that have passed RADIUS portal authentication may have higher RADIUS accounting traffic statistics.

 

Notes:         

1. For OC300 (UN) V1 Only.

2. Omada SDN Controller can configure and manage only certain devices with supported firmware. You need to make sure your device is compatible with Omada SDN Controller.

3. If you are using Omada Controller and plan to upgrade to this version, please follow the procedure of the Omada Controller Upgrade Guide.

4. Once upgraded to this version of Omada Controller, you will be NOT able to downgrade to version 3.2.10 or below. 

5. This version of the controller is applied to the Omada APP of version 3.0.X or above.

 

OC300(UN)_V1_1.0.3_Build_20201119
Published Date: 2020-12-18 Language: English File Size: 118.6MB

If you are planning to upgrade from the old controller(v3.2.10 or below) to this version, please read the Omada Controller Upgrade Guide in the installation package before upgrading the controller.

 

Supported device models and firmware:

EAP:

EAP110_V4 3.20.0 Build 20200525 Rel. 36899 and above

EAP115_V4 3.20.0 Build 20200525 Rel.36931 and above

EAP225_V3 2.20.0 Build 20200422 Rel. 70513 and above

EAP245_V3 2.20.0 Build 20200423 Rel. 36779 and above

EAP115-Wall_V1 1.20.0 Build 20200509 Rel. 63986 and above

EAP225-Wall_V2 1.20.0 Build 20200422 Rel. 70504 and above

EAP110-Outdoor_V3 3.20.0 Build 20200511 Rel. 33388 and above

EAP225-Outdoor_V1 1.20.0 Build 20200422 Rel. 70543 and above

EAP265 HD_V1, EAP230-Wall_V1, EAP235-Wall_V1, EAP660 HD_V1, EAP620 HD_V1

Switch:

TL_SG3428MP_V1, TL_SG3428_V1, TL-SG2210MP_V1, TL-SG2210P_V3.20, TL-SG2428P_V1, TL-SG2008P_V1, TL-SG2008_V3, TL-SG3428X_V1, TL_SG3428XMP_V1, TL-SG3210XHP-M2_V1

Gateway:

TL-R605_V1, TL-ER7206_V1

 

New Feature/Enhancement:

1. Support to manage TL-SL2428P(UN) 4.20.

2. Optimize the protocol for the device reporting information of rate/duplex capability.

3. Optimize the password retrieval mechanism. If multiple local accounts are bound to one mailbox, you can choose which account to reset the password.

4. Add the batch cancelling of devices migration in the migration function.

5. Vulnerability optimization

 

Bug Fixed:

1. Fixed the bug that the device will move to the upper left corner when you visit again if the device location is locked in the MAP.

2. Fixed the bug that uplink signal strength of Mesh EAP is not displayed accurately on the devices private configuration page.

3. Fixed the bug that the user without device permission may display that it still has permission in the account settings.

4. Fixed the bug that the function of Log Server/Alert Email may not take effect after restoring the backup file of Controller.

5. Fixed the bug that you may unsuccessfully import the local user account in the Hotspot Manager.

6. Fixed the bug that the “Last Seen” time in the private configuration page of the switch is the last uptime (not the last disconnected time) after the switch disconnects from Omada Controller.

7. Fixed the bug that the expiration time of Facebook authentication in “->authorized clients” is inconsistent with the actual expiration time.

8. Fixed the bug that the Controller may generate lots of roaming logs if clients leave from one EAP to another EAP implicitly since clients still send auth frame to the previous EAP.

 

Notes:

1.  For OC300(UN) V1 Only.

2.  Omada SDN Controller can configure and manage only certain devices with supported firmware. You need to make sure your device is compatible with Omada SDN Controller.

3.  If you are using Omada Controller and plan to upgrade to this version, please follow the procedure of Omada Controller Upgrade Guide.

4.  Once upgraded to this version of Omada Controller, you will be NOT able to downgrade to version 3.2.10 or below. 

5.  This version of the controller is applied to Omada APP of version 3.0.X or above.

To Use Third Party Firmware In TP-Link Products

Some official firmware of TP-Link products can be replaced by the third party firmware such as DD-WRT. TP-Link is not obligated to provide any maintenance or support for it, and does not guarantee the performance and stability of third party firmware. Damage to the product as a result of using third party firmware will void the product's warranty.

Open Source Code For Programmers (GPL)

Please note: The products of TP-LINK partly contain software code developed by third parties, including software code subject to the GNU General Public Licence (“GPL“), Version 1/Version 2/Version 3 or GNU Lesser General Public License ("LGPL"). You may use the respective software condition to following the GPL licence terms.

You can review, print and download the respective GPL licence terms here. You receive the GPL source codes of the respective software used in TP-LINK products for direct download and further information, including a list of TP-LINK software that contain GPL software code under GPL Code Center.

The respective programs are distributed WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the respective GNU General Public License for more details.

Omada Discovery Utility

Published Date: 2020-07-07 Language: English File Size: 31.11 MB
Operating System: WinXP/Vista/7/8/8.1/10/Server2008/Server2012/Mac OS X 10.7/10.8/10.9/10.10/10.11

New Feature/Enhancement:

1. Fully adapted to Omada SDN Controller v4.1.4.

2. Support to discover the gateway and switch that support Omada SDN platform.

 

Note:

1. This version of software can be used in both Windows and Mac operation system.

2. Double click the software or run the command “java –jar **.jar” to run the software on MacOS (**.jar is the name of this software).

3. To run this software, you need to install JRE 8.0 on your PC first.

4. Omada Controller and Discover Utility cannot run on the same computer at the same time.

Published Date: 2019-08-06 Language: English File Size: 25.85 MB
Operating System: WinXP/Vista/7/8/8.1/10/Server2008/Server2012/Mac OS X 10.7/10.8/10.9/10.10/10.11

Bug fixed:

1. Fixed the bug that the Discovery Utility may fail to find EAPs.

2. Fixed the bug that the Cancel button may overlap with the display box after managing APs.

 

Note:

1. This version of software can be used in both Windows and Mac operation system.

2. Double click the software or run the command “java –jar **.jar” to run the software on MacOS (**.jar is the name of this software).

3. To run this software, you need to install JRE 8.0 on your PC first.

Published Date: 2019-06-14 Language: English File Size: 23.54 MB
Operating System: WinXP/Vista/7/8/8.1/10/Server2008/Server2012/Mac OS X 10.7/10.8/10.9/10.10/10.11

Bug fixed:

1. Fixed the bug that when the Discovery Utility issues Controller_IP to EAPs which are in factory status, Controller cannot batch manage the EAPs.

2. Fixed the bug that sometimes the Discovery Utility cannot find all EAPs when running in MacOS.

Note:

1. This version of software can be used in both Windows and Mac operation system.

2. Double click the software or run the command “java –jar **.jar” to run the software on MacOS(**.jar is the name of this software).

3. To run this software, you need to install JRE 8.0 on your PC.

Published Date: 2018-07-24 Language: English File Size: 84.16 MB
Operating System: Mac OS X 10.7/10.8/10.9/10.10/10.11

New Feature/Enhancement:
1. Change name to "Omada Discovery Utility".
2. Update background picture during installation.
3. Limit the maximum length of controller hostname to 79.
 
Bug Fixed:
Fix the bug that searching in the search box will cause the software to hang.
 
Note:
Operating System: Mac OS X 10.7/10.8/10.9/10.10/10.11.

T2700G-28TQ License Download
License Model: T2700G-28TQ-L1000

Find your product MAC and Serial Number.
License Key:
Product Serial Number:
Product MAC:
Checking code:

Join TP-Link CommunityTP-Link takes your privacy seriously. For further details on TP-Link's privacy practices, see TP-Link's Privacy Policy.

From United States?

Check products and services for your region.