How to add VIGI devices to VIGI local VMS

Configuration Guide
Updated 10-28-2024 08:03:48 AM 1328
This Article Applies to: 

Contents

Objective

Requirements

Introduction

Configuration

Auto Add

Manually Add

Remotely Add

Conclusion

Objective

VIGI Local VMS provides centralized cloud management for VIGI Cameras, VIGI NVRs, and VIGI Solar Panels. This article describes how to add VIGI devices to VIGI Local VMS.

Requirements

  • VIGI Local VMS
  • VIGI Camera/VIGI NVR

Introduction

VIGI Local VMS installs the Server on a Windows PC, which is generally used to centrally manage the devices within the same LAN network. Follow the three methods below to add devices to VIGI Local VMS:

Auto Add: Automatically scan and add VIGI devices in the same network segment as the Server.

Manually Add: Manually enter a specific IP address or IP range, and the Server will perform a targeted search and add the device to VIGI Local VMS.

Remotely Add: The method of adding devices that are not in the same network segment as the server. This method requires VIGI devices to actively initiate a connection request with VIGI VMS. To use this method, port forwarding settings are required.

Configuration

Auto Add

Step 1. Log in to the web portal of Local VMS, and click Device to enter the device management page.

The Device List page in VIGI VMS web portal.

Step 2. Click Add on the top right corner of the Device List and select Auto Add. The VMS will then automatically search and display VIGI devices in the same network segment.

The Scan Result in the VIGI VMS Web Portal.

Step 3. Select the desired device, click the Add button, and select the corresponding site in the pop-up window.

 Site Selection Pop-up in VIGI VMS Web Portal.

Step 4. Enter the password of the device, and then click Confirm.

Password Pop-up in VIGI VMS Web Portal.

Step 5. Done. Now the device has been added to the VMS.

Manually Add

Step 1. Log in to the web portal of Local VMS, and click Device to enter the device management page.

The Device List page in VIGI VMS web portal.

Step 2. Click Add on the top right corner of the Device List, select Manually Add, and then select the Add Method according to the number of devices to be added.

Pop-up for Adding Single Device IP.

Pop-up for Adding IP Range.

Step 3. Enter the corresponding IP address and click Obtain Device. When the device is detected, the device information will be displayed.

 Obtained Device Information.

Step 4. Click Add Device, select a site, and enter the device password.

Site Selection Pop-up.

Password Pop-up window in the VIGI VMS Web Portal.

Step 5. Done. Now the device has been added to the VMS.

Remotely Add

Remotely Add is usually used when the VIGI VMS Server is located within NAT and the VIGI device is at a remote location. In this case, the device needs to be connected to the server via the internet. Therefore, Remotely Add requires both good network connectivity and port forwarding settings on the NAT device.

In addition, using Remotely Add will expose the Server to the public internet, which is less secure than using a local network. For such distributed network management, it is recommended to use VIGI Cloud VMS.

Step 1. Configure port forwarding on the router connected to the Server. Here we need to configure the ports as 8081, 8082, 10123 and 10556.

Step 2. Log in to the web management interface of the remote VIGI device, and then go to Settings > Network Settings > Platform Access.

Step 3. Enable Access to VIGI VMS, enter the public IP address of the router connected to the VIGI VMS, and configure the port for connecting VMS (10123 by default).

The Platform Access option in the VIGI Device’s web management interface.

Step 4. Log in to the web portal of VIGI Local VMS, click Device to enter the device management page, click Add, and select Remotely Add. Then a remote IPC device will be displayed in the device list.

Device List of Remotely Add.

Step 5. Click the Add button, select the site and enter the device’s password.

Pop-up for Selecting Site.

Pop-up for Entering Password.

Step 6. Click Confirm. Now the device has been added to the VMS.

Conclusion

You have now successfully added VIGI devices to the VIGI Local VMS.

Get to know more details of each function and configuration please go to Download Center to download the manual of your product.

Related FAQs

Looking for More

Чи була ця стаття корисною?

Ваш відгук допомагає вдосконалити цей сайт.

Recommend Products

From United States?

Get products, events and services for your region.