-
Для дома
Быстрый и надежный Wi-Fi
Доступный интернет
Проводные соединения в вашем доме для улучшенного качества связи
Всё для вашего удобства
-
Умный дом
Не выпускайте из поля зрения самое дорогое
Умные устройства вашего дома
Яркая подсветка на любой вкус
-
Для бизнеса
Высокоскоростная проводная сеть от неуправляемых до L3-коммутаторов
Professional business Wi-Fi with centralized management
Идеальное решение для беспроводных широкополосных сетей большой дальности
Шлюзы с Load Balance и Secure VPN для вашего бизнеса
Умное облачное решение для бизнес-сетей
Видеонаблюдение VIGI - ваша безопасность
-
Для операторов связи
Обеспечивает стабильную широкополосную связь на больших скоростях
Надежный выбор для домашних сетей
Доступ к мобильному интернету в любой точке планеты
Технология предоставления гигабитных подключений
Используют электрическую проводку для передачи сигнала сети
Легко расширяйте свое покрытие Wi-Fi
Производительность премиум-класса для вашей сети
Поднимите Wi-Fi вашего предприятия на новый уровень
How to configure free authentication policy on EAP Controller
Suitable for: Omada Controller 2.6.0 or above and EAP products with corresponding firmware.
What is Free Authentication Policy?
Free Authentication Policy is used to control the access to the network resources for clients. This function allows some specified clients to access the specified network resources without authentication. Omada Controller supports two match modes: IP-Mac based mode and URL mode.
Free Authentication Policy often works with Portal. With Portal enabled, clients that didn’t pass Portal authentication can only access the network resources allowed by Free Authentication Policy.
How Do I Configure Free Authentication Policy?
Follow these steps to configure Free Authentication Policy:
1. Launch Omada Controller and log in to the management interface.
2. Click on the upper right corner of the management interface. Go to Wireless Control > Free Authentication Policy.
3. Click and configure the policy.
IP-Mac based mode
1) Specify the Match Mode as IP-Mac based. Then give a name for this policy.
2) (Optional) Specify the Source IP Range in which the clients can access the specified network resources. Here we take 192.168.0.0/24 as an example.
3) (Optional) Specify the Destination IP Range of the network resources that is available for the specified clients. Here we take 192.168.0.100/32 as an example.
4) (Optional) Specify the MAC address of the client for the Source MAC. Here we leave this option empty.
5) (Optional) Specify the port number that the service uses for the Destination Port. Here we take 80 as an example.
6) Click Enable to enable this policy.
Note:
- A policy applies to the traffic that matches all the conditions.
- If you leave the optional parameters empty, all the clients can access the network resources without limitation.
URL mode
1) Specify the Match Mode as URL. Then give a name for this policy.
2) Specify the URL that the clients can access. Here we take www.tp-link.com as an example.
3) Click Enable to enable this policy.
4. Click Apply.
Note: The valid port numbers of URL are from 1024 to 65535.
Ваш отзыв поможет нам улучшить работу веб-сайта.
Подписаться на рассылкуМы с ответственностью относимся к вашим персональным данным. Полный текст политики конфиденциальности доступен здесь.