What should I do when the Omada Software Controller (V3 or below) fails to discover the EAP?

Troubleshooting
Updated 07-23-2024 03:28:24 AM FAQ view icon84109
This Article Applies to: 

If your Omada Controller is V4.1.5 or above, please refer to FAQ 2980

This article provides steps and suggestions to help you solve a problem that the controller cannot discover the EAP. The overview of the steps is shown in the following picture.

Step 1: Check the Power LED

Make sure the EAP is powered on and its Power LED is stable green.

Step 2: Check the IP address of EAP on the DHCP Server

Go to the DHCP server to find EAP’s IP address. Make sure the EAP gets an IP address without IP conflicts from the DHCP server.

Step 3: Check the network connection using the Ping command

Ping the IP address of the EAP on the computer running the controller to check if the EAP is accessible. (By default, its IP address is 192.168.0.254.)

If the computer running the controller can access the EAP, refresh the web management page to check if the EAP is discovered.

If the computer cannot access the EAP or the EAP is still not discovered, go to the next step.

Step 4: Check the network settings according to its topology

Different configurations are needed according to your network topology. Make sure the configurations are suitable and correct.

The following introduces needed network configurations for different topologies.

Ÿ If the controller and EAP are in the same VLAN and subnet (as shown below), there is no extra needs about the network configuration. Go to Step 5: Enable ports 29810-29813 on the management device.

Ÿ If the EAPs are in different VLANs (as shown below), configure VLANs on the Layer 2 switch. For detailed steps, refer to FAQ-1365.

Ÿ If the controller and EAP are in different subnets (as shown below), run a Discover Utility on a computer or configure DHCP option 138 on the Layer 3 switch so that they can communicate with each other. For detailed steps to discover EAPs in different VLANs, refer to FAQ-1359 (using Discover Utility) or FAQ-1360 (configuring DHCP option 138).

Ÿ If the controller and EAP are in different sites (as shown below), configure VPN Tunnel or Port Forwarding on the router.

For detailed information about configuring these two features, refer to the following FAQs according to the method you use.

Feature Configuration

Method

Corresponding FAQ

Configuring VPN Tunnel

Discover Utility

FAQ-1361

DHCP option 138

FAQ-1362

Configuring NAT Port Forwarding

Discover Utility

FAQ-1363

DHCP option 138

FAQ-1364

Step 5: Enable ports 29810–29813 on the management device

Check the firewall and antivirus software to make sure TCP/UDP ports 29810–29813 is enabled on the computer, or directly disable the firewall and antivirus software.

EAPs communicate with the controller via TCP/UDP ports 29810-29813. If the firewall and antivirus software block these ports, they also block the packets between the controller and EAPs.

Step 6: Install Discover Utility to collect more information

Follow the instructions below to get detailed information about your problem and help the TP-Link support team solve the problem faster.

* To run the utility, close the controller first. The controller and utility cannot run together on one computer. Click to download the latest Discover Utility

** If the utility cannot discover the EAP, confirm if the EAP sends the discovery packet first. Keep the current network topology and capture packets in the LAN port of EAP to analyze the situation. The packets with the following features are discovery packets:

*** Our Technical Support contact information can be found at https://www.tp-link.com/support/contact-technical-support/.

Related Articles

Introduction of EAP Adoption

How to Adopt EAPs in Controller Mode?

What Should I Do if Omada Software Controller/OC200 Cannot Adopt Omada EAP?

Looking for More

Is this faq useful?

Your feedback helps improve this site.

Recommend Products

Community

TP-Link Community

Still need help? Search for answers, ask questions, and get help from TP-Link experts and other users around the world.

Visit the Community >

From United States?

Get products, events and services for your region.