Search
Search

How to configure 802.1Q VLAN on TP-Link Load Balance and VPN routers using the new GUI?

Configuration Guide
Updated 01-29-2019 06:22:33 AM 53525
Ez a leírás a következő eszköz(ök)re alkalmazható:: 

 

VLAN (Virtual Local Area Network) is a technology that can solve broadcasting issues. A LAN can be divided into several VLANs logically, and only the hosts in a same VLAN can communicate with each other.

Here is a configuration example of 802.1Q VLAN for TP-Link routers.

Example:

As the following figure shows, the switch connects to two different groups. It is required that the computers in the two groups cannot communicate with each other, but both of them can access the internet via the router.

Configuration Scheme

Configure 802.1Q VLAN on the router:

1) Create VLAN 2 and VLAN 3, and add port 5 (the LAN port) to both VLANs with the egress rule as Tagged.

Configure 802.1Q VLAN on the switch:

1) Create VLAN 2. Add port 1, 2 to VLAN 2.

2) Create VLAN 3. Add port 1, 3 to VLAN 3.

VLAN Configurations on the Router:

 

VLAN

Egress Rule

PVID

Port 5

VLAN 2-3

Tagged

-

 

VLAN Configurations on the Switch:

 

VLAN

Egress Rule

PVID

Port 1

VLAN 2-3

Tagged

-

Port 2

VLAN 2

Untagged

2

Port 3

VLAN 3

Untagged

3

Note: The PVID value “-” means you don’t need to configure the PVID for the corresponding port, just leave them as the default value.

Configuration Steps:

The router is demonstrated with TL-R600VPN, and the switch is demonstrated with TL-SG105E. The following section shows how to configure 802.1Q VLAN on the router and switch.

  • Configuring 80.21Q VLAN on the router

Choose the menu Network >VLAN > VLAN, click  to load the configuration page. Create VLAN 2, 3 and add port 5 to both of the VLANs with the egress rule as Tag.

  • Configuring 80.21Q VLAN on the switch

Step 1:

Choose the menu VLAN > 802.1Q VLAN to load the configuration page. Enable 802.1Q VLAN function. Add port 1, 2 to VLAN 2 and port1, 3 to VLAN 3 as untagged ports. Specify the egress rule of port 1 as tagged in VLAN 2and VLAN 3; specify the egress rule of port 2 in VLAN 2as untagged; specify the egress rule of port 3 in VLAN 3 as untagged.

Step 2:

Choose the menu VLAN > 802.1Q PVID Setting to load the configuration page. Configure the PVIDs for port 2-3 as 2 and 3 respectively, and leave the PVID of port 1 as the default value 1.

Feliratkozás a hírlevélreA TP-Link komolyan veszi az adatok védelmét. További információért látogassa meg a TP-Link Adatvédelmi irányelvek oldalt..

Követés

Rólunk
Sajtó
Hol kapható?
Learning Center
Magyarország / Magyar
Copyright © 2021 TP-Link Corporation Limited. Minden jog fenntartva.
A honlapon szereplő adatok tájékoztató jellegűek. Az oldal szerzője semmilyen felelősséget nem vállal az adatok pontatlanságából eredő károkért.

From United States?

Check products and services for your region.

Go Other Option