-
Σπιτι
Η πόρτα σας στο Διαδίκτυο
Εύκολοι τρόποι επέκτασης και βελτίωσης του δικτύου σας
Διατηρώντας το σπίτι σας ενσύρματο για ποιοτικές συνδέσεις
Εξοπλίστε τις συσκευές σας για ταχύτερο Wi-Fi
Όλα όσα χρειάζεστε για έναν συνδεδεμένο τρόπο ζωής
-
Εξυπνο Σπιτι
Παρακολουθώντας ότι έχει σημασία
Κάντε τις οικιακές σας συσκευές πιο έξυπνες
Φως για κάθε περίσταση
-
Επιχειρησεις
High-Speed ενσύρματη δικτύωση από L3 managed μέχρι unmanaged
Επαγγελματικό επιχειρηματικό Wi-Fi με κεντρική διαχείριση
Η πιο έξυπνη λύση cloud για επιχειρηματική δικτύωση
Ιδανικό για ασύρματη ευρυζωνική δικτύωση μεγάλης εμβέλειας
-
Παροχοι Ιντερνετ
Δυνατότητα υψηλής ταχύτητας δικτύου και ολοκληρωμένων ευρυζωνικών εφαρμογών
Μετατρέπει την ηλεκτρική καλωδίωση για να μεταφέρει το σήμα δικτύου.
Επεκτείνετε εύκολα την κάλυψη Wi-Fi.
Ενισχύει το επιχειρηματικό σας δίκτυο με εξαιρετική απόδοση.
Μεταφέρει το εταιρικό σας Wi-Fi σε νέα επίπεδα.
How to set up rate limit through EAP controller
Suitable for: Omada Controller 2.5.1 or above and EAP products with corresponding firmware.
What is Rate Limit?
Rate Limit is used to set the limit of download rate and upload rate for the clients. With Rate Limit configured, we can protect the network bandwidth from being occupied too much by some of the clients.
Omada Controller supports three types of rate limit: Rate Limit Based on SSID, Rate Limit Based on Clients and Rate Limit Based on Voucher/Local User. When you configure more than one type of rate limit at the same time, only the configuration with minimum rate limit value will take effect.
Note: Only Omada Controller 2.6.0 or above supports Rate Limit Based on Clients.
How Do I Configure Rate Limit?
1. Click on the upper right corner of the management interface. Go to Wireless Settings > Basic Wireless Setting to load the following page.
2. Click to configure the corresponding SSID, and click Rate Limit to load the following page.
3. In the Rate Limit section, enable Rate Limit and specify the download limit and upload limit. Click Apply.
Note: Before configuring Rate Limit Based on Clients, make sure that there are clients connected to the controller.
1. Go to Clients and click to configure the corresponding client. Then click Rate Limit to load the following page.
2. Specify the download limit and upload limit. Click Apply.
Note: Before configuring Rate Limit Based on Voucher/Local User, configure Voucher/Local User Portal first.
For Voucher
1. Click on the upper right corner of the management interface. Go to Wireless Control > Portal to load the following page.
2. Click to configure the corresponding Voucher Portal. Click Voucher Manager to manage the vouchers.
3. On the Management page, go to Voucher and click to create vouchers and specify the download limit and upload limit. Click Apply.
For Local User
1. Click on the upper right corner of the management interface. Go to Wireless Control > Portal to load the following page.
2. Click to configure the corresponding Local User Portal. Click User Management to manage the users.
3. On the Management page, go to User and click to create local users and specify the download limit and upload limit. Click Apply.
Your feedback helps improve this site.
ΕγγραφήTP-Link takes your privacy seriously. For further details on TP-Link's privacy practices, see TP-Link's Privacy Policy.