Tải về cho EAP245 V3

Please choose hardware version:

V3

>Làm sao để biết phiên bản phần cứng của thiết bị TP-Link

IMPORTANT: Model and hardware version availability varies by region. Please refer to your TP-Link regional website to determine product availability.
Product Overview
Tài Liệu
Access Point Gắn Trần Gigabit Wi-Fi MU-MIMO AC1750
EAP245

Setup Video

  • How to manage TP-Link EAPs centrally via the Software Controller

    This video demonstrates how to manage TP-Link EAPs centrally via the Software Controller. The setup consists of three steps:
    • Install the Software
    • Configure Discovery Utility (If your EAPs and the Controller Host are on different subnets)
    • Configure Software Controller

    THIS VIDEO APPLIES TO:
    • All TP-Link EAP models (except EAP120 and EAP220)
    • Omada Software Controller
    • Mass EAPs (usually more than three)

    Learn More

  • How to set up a TP Link EAP via your mobile phone

    This video demonstrates how to set up a TP-Link EAP via your mobile phone. The setup consists of four steps:
    • Connect the EAP to the network
    • Download the Omada APP
    • Connect to the EAP's wireless network
    • Set up the EAP using the Omada APP

    THIS VIDEO APPLIES TO:
    • All TP-Link EAP models. (except EAP120 and EAP220)
    • A small number (1-3) of EAPs.

    Learn More

  • How to setup the OC200 via a web browser

    This video will demonstrate how to set up the OC200 via a web browser. The setup consists of six steps:
    • Connect the OC200 to your local network.
    • Get ready for setup.
    • Create a TP-Link ID.
    • Log into your TP-Link ID.
    • Add the OC200 to your TP-Link ID.
    • Follow the wizard to set up the OC200.

    THIS VIDEO APPLIES TO:
    • All TP-Link EAP models (except EAP120 and EAP220)
    • Omada Cloud Controller OC200
    • Mass EAPs (usually more than three)

    Learn More

  • How to setup the OC200 via your mobile phone

    This video will demonstrate how to set up the OC200 via your mobile phone. You need to use the Omada APP to complete the setup. The setup consists of six steps:
    • Connect the OC200 to your local network.
    • Get ready for setup.
    • Create a TP-Link ID.
    • Log into your TP-Link ID.
    • Add the OC200 to your TP-Link ID.
    • Follow the wizard to set up the OC200.
    THIS VIDEO APPLIES TO:
    • All TP-Link EAP models (except EAP120 and EAP220)
    • Omada Cloud Controller OC200
    • Mass EAPs (usually more than three)

    Learn More

  • How to manage TP-Link EAPs centrally from a remote place via a web browser

    You can manage TP-Link EAPs at any time from anywhere with the Cloud Access function of our Omada Controller Software. This video introduces both the application scenario and concrete steps you can follow. Don't hesitate to give it a try.
    THIS VIDEO APPLIES TO:
    • All TP-Link EAP models (except EAP120 and EAP220)
    • Omada Controller Software (version 3.0.2 or above)
    • Mass EAPs (usually more than three)

    Learn More

  • A Quick Overview of EAP Management Methods

    This video introduces how to choose the optimum method to manage TP-Link EAPs in your scenario.
    Here are 3 most common scenarios and their corresponding methods:
    • Manage 1 or 2 EAPs locally
    • Manage 3 or more EAPs locally
    • Manage 3 or more EAPs remotely
    When choosing the method, consider the following questions:
    1. Standalone Mode or Controller Mode?
    2. In Controller mode, what kind of controller will you use, an OC200 or a PC with Omada Software Controller?
    3. What kind of user interface will you use, a web browser or the Omada app?

    Learn More

  • How to Set up a TP-Link EAP via Web browser

    This video will demonstrate how to set up a TP-Link EAP via a web browser. The setup consists of three steps:
    1. Connect the EAP to the network
    2. Log into the EAP (via a wired/wireless connection)
    3. Change the default SSID
    This video is suitable for users with a small number (1-3) of EAPs .

    Learn More

Feature Filter: Tất Cả Configuration GuideQ&A of functional explanation or specification parametersUser Application RequirementTroubleshooting

FAQs

Firmware

A firmware update can resolve issues that the previous firmware version may have and improve its current performance.

To Upgrade

IMPORTANT: To prevent upgrade failures, please read the following before proceeding with the upgrade process

  • Please upgrade firmware from the local TP-Link official website of the purchase location for your TP-Link device, otherwise it will be against the warranty. Please click here to change site if necessary.
  • Please verify the hardware version of your device for the firmware version. Wrong firmware upgrade may damage your device and void the warranty. （Normally V1.x=V1）
    Làm sao để biết phiên bản phần cứng của thiết bị TP-Link
  • Do NOT turn off the power during the upgrade process, as it may cause permanent damage to the product.
  • To avoid wireless disconnect issue during firmware upgrade process, it's recommended to upload firmware with wired connection unless there is no LAN/Ethernet port on your TP-Link device.
  • It's recommended that users stop all Internet applications on the computer, or simply disconnect Internet line from the device before the upgrade.
  • Use decompression software such as WinZIP or WinRAR to extract the file you download before the upgrade.
EAP245(EU)_V3_191029
Ngày Phát Hành: 2020-01-14 Ngôn Ngữ: English File Size: 8.06 MB

Recommended Controller Software Version: Omada Controller v3.2.x or above

Bug Fixed:
1. Fixed the bug that EAP may disconnect from Omada Controller.
2. Fixed the bug that the time zone displayed on the web UI of Standalone mode may be different from the connected PC.

Notes:
1. For EAP245 v3 only.
2. Your device's configuration won't be lost after upgrading.
3. This version of firmware is applied to Omada APP of version 2.1.X or above.
4. You cannot downgrade if you upgrade from 2018 or older firmware to this version directly.
EAP245(EU)_V3_190731
Ngày Phát Hành: 2019-10-17 Ngôn Ngữ: English File Size: 8.05 MB

Recommended Controller Software Version: Omada Controller v3.2.x or above

New Feature/Enhancement:

1. Change the OpenSSL version to 1.0.2q.

2. Optimize UI, including character optimization and display error correction.

3. Update the time zone of Caracas from GMT-4:30 to GMT-4:00.

 

Bug Fixed:

1. Fixed the bug that client devices can pass the portal authentication after disconnected from the Controller.

2. Fixed the bug that untag packets can be transferred to SSIDs with different VLANs.

3. Fixed the bug that channel 12/13 cannot be set correctly.

4. Fixed the bug that some EAPs may disconnect from the Omada Controller in large scale network.

5. Fixed the bug that the management page may not be accessed after EAP is disconnected from the Controller.

6. Fixed the bug that when APs are disconnected from Controller, the rate limit configuration will be not issued to these APs after they are back to connected again.

7. Fixed the bug that when the time of EAP is synchronized with PC, it will be the same as PC's time not considering different time zones.

8. Fixed the bug that packets with VLAN tag can be forwarded to the SSID without wireless VLAN setting.

 

Notes:

1. For EAP245 v3 only.

2. Your device's configuration won't be lost after upgrading.

3. This version of firmware is applied to Omada APP of version 2.1.X or above.
EAP245(EU)_V3_190530
Ngày Phát Hành: 2019-07-09 Ngôn Ngữ: English File Size: 7.66 MB

Recommended Controller Software Version: Omada Controller v3.1.x or above

 

New Feature/Enhancement

1. Add Radius Accounting to External Radius Server in standalone mode.

2. Add SSID Radius accounting to WPA-Enterprise security mode.

3. Add SSL encryption in Auto Mail of Log Settings.

4. Support the feature of merging 2.4GHz and 5GHz SSID with Controller 3.1.4.

5. Support SSID MAC Authentication to none security mode with Controller 3.1.4.

6. Support channel utilization function with Controller 3.1.4.

7. Support Layer-3 Accessibility in SSH with Controller 3.1.4.

8. Change the rule of the LED when resetting/rebooting EAP.

9. Support UTF8 in SSID character.

10. Optimize Band Steering feature.

 

Bug Fixed:

1. Fixed the bug that the client rate limit doesn't take effect under batch configuration.

2. Fixed the bug that clients cannot access tplinkeap.net in a mixed network of IPv4 and IPv6.

3. Fixed the bug that clients maybe disconnected when enabling Airtime Fairness in 2.4G frequency.

4. Fixed the bug that some SSIDs cannot broadcast when restoring the configuration on the Controller.

 

Notes:

1. For EAP245 v3 only.

2. Your device's configuration won't be lost after upgrading.

3. This version of firmware is applied to Omada APP of version 2.1.X or above.

Sử dụng Firmware của bên thứ 3 trên sản phầm TP-Link

Một số firmware chính thức của các sản phẩm TP-LINK có thể được thay thế bằng firmware của bên thứ ba chẳng hạn như DD-WRT. TP-LINK không cung cấp vấn đề hỗ trợ kĩ thuật và đảm bảo hiệu năng cũng như tính ổn định của firmware bên thứ ba. Khi sản phẩm bị hư hại do sử dụng firmware của bên thứ 3 thì chế độ bảo hành sản phẩm sẽ bị vô hiệu.

 

Controller Software

Bộ điều khiển EAP được sử dụng để quản lý nhiều EAP một cách mạnh mẽ.

Ngày Phát Hành: 2020-01-21 Ngôn Ngữ: English File Size: 120.53MB
Hệ Điều Hành: Windows 7/8/10/Server

New Feature/Enhancement:

1. Expand the number of Omada Controller’s User Account to 500.  

2. Optimize the External Portal Server to support URL with parameters.

 

Notes:

1. To use Omada Controller 3.2.X new features, you need to upgrade your EAP's firmware to the corresponding version.

2. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

3. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.X or earlier version.

 
Ngày Phát Hành: 2020-01-21 Ngôn Ngữ: English File Size: 124.45MB
Hệ Điều Hành: Windows 7/8/10/Server

New Feature/Enhancement:

1. Expand the number of Omada Controller’s User Account to 500.  

2. Optimize the External Portal Server to support URL with parameters.

 

Notes:

1. To use Omada Controller 3.2.X new features, you need to upgrade your EAP's firmware to the corresponding version.

2. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

3. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.X or earlier version.
Ngày Phát Hành: 2020-01-16 Ngôn Ngữ: English File Size: 123.35MB
Hệ Điều Hành: Ubuntu 14.04/16.04/17.04/18.04, CentOS 6.x/7.x and Fedora 20 or above, Debian 9.8.

New Feature/Enhancement:

1. Change the mechanism that when adopting an EAP, the Controller will retain the IP configuration of EAP in Standalone mode.

2. Change the mechanism that multiple Omada Controllers can run on the same subnet.

3. Add the button of “Start Omada Controller after installation” and check it by default.

4. Extend the Max Associated Clients in Load Balance to 255.

5. Optimize the UI of Channel Utilization.

6. Optimize the authentication page of portal.

7. Optimize the UI of the portal that you cannot click Apply when you are uploading a photo.

8. Optimize the External Portal Server to support URL with parameters.

 

Bug Fixed:

1. Fixed the bug that the page of MAC filter may not display all groups when there are more than 5 groups.

2. Fixed the bug that after deleting a site, the Voucher code and Local user of this site still exist.

3. Fixed the bug that the site configuration will fail to restore when the imported site contains same Voucher code as the current Controller.

4. Fixed the bug that when mesh AP is powered off during upgrade, Controller may fail to upgrade other APs, with a prompt message “Other APs are upgrading”.

 

Notes:

1. To use new features on Omada Controller 3.2.x, you need to upgrade your EAP's firmware to the corresponding version.

2. The Omada Controller program needs to use the system's netstat command. If the Linux system does not have net-tools installed (which contain the netstat command), the program may not be able to run normally.

3. Support 64-bit Linux operating system including Ubuntu 14.04/16.04/17.04/18.04, CentOS 6.x/7.x and Fedora 20 or above, Debian 9.8.

4. Built-in JRE 1.8 Java environment.

5. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

6. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.8.

7. When upgrading from Controller 2.5.3 Linux to this version via install.sh, you need to uninstall old version of Controller first.

 
Ngày Phát Hành: 2020-01-16 Ngôn Ngữ: English File Size: 99.4MB
Hệ Điều Hành: Ubuntu 14.04/16.04/17.04/18.04/Debian 9.8

New Feature/Enhancement:

1. Change the mechanism that when adopting an EAP, the Controller will retain the IP configuration of EAP in Standalone mode.

2. Change the mechanism that multiple Omada Controllers can run on the same subnet.

3. Add the button of “Start Omada Controller after installation” and check it by default.

4. Extend the Max Associated Clients in Load Balance to 255.

5. Optimize the UI of Channel Utilization.

6. Optimize the authentication page of portal.

7. Optimize the UI of the portal that you cannot click Apply when you are uploading a photo.

8. Optimize the External Portal Server to support URL with parameters.

 

Bug Fixed:

1. Fixed the bug that the page of MAC filter may not display all groups when there are more than 5 groups.

2. Fixed the bug that after deleting a site, the Voucher code and Local user of this site still exist.

3. Fixed the bug that the site configuration will fail to restore when the imported site contains same Voucher code as the current Controller.

4. Fixed the bug that when mesh AP is powered off during upgrade, Controller may fail to upgrade other APs, with a prompt message “Other APs are upgrading”.

 

Notes:

1. To use new features on Omada Controller 3.2.X, you need to upgrade your EAP's firmware to the corresponding version.

2. The Omada Controller program needs to use the system's netstat command. If the Linux system does not have net-tools installed (which contain the netstat command), the program may not be able to run normally.

3. Support 64-bit Linux operating system including Ubuntu 14.04/16.04/17.04/18.04/Debian 9.8

4. Built-in JRE 1.8 Java environment.

5. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

6. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.8.
Ngày Phát Hành: 2020-01-09 Ngôn Ngữ: English File Size: 120.53MB
Hệ Điều Hành: Windows 7/8/10/Server

New Feature/Enhancement:

1. Change the mechanism that when adopting an EAP, the Controller will retain the IP configuration of EAP in Standalone mode.

2. Change the mechanism that multiple Omada Controllers can run on the same subnet.

3. Add the button of “Start Omada Controller after installation” and check it by default.

4. Extend the Max Associated Clients in Load Balance to 255.

5. Optimize the UI of Channel Utilization.

6. Optimize the authentication page of portal.

7. Optimize the UI of the portal that you cannot click Apply when you are uploading a photo.

 

Bug Fixed:

1. Fixed the bug that the page of MAC filter may not display all groups when there are more than 5 groups.

2. Fixed the bug that after deleting a site, the Voucher code and Local user of this site still exist.

3. Fixed the bug that the site configuration will fail to restore when the imported site contains same Voucher code as the current Controller.

4. Fixed the bug that when mesh AP is powered off during upgrade, Controller may fail to upgrade other APs, with a prompt message “Other APs are upgrading”.

 

Notes:

1. To use Omada Controller 3.2.X new features, you need to upgrade your EAP's firmware to the corresponding version.

2. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

3. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.X or earlier version.
Ngày Phát Hành: 2020-01-09 Ngôn Ngữ: English File Size: 124.44MB
Hệ Điều Hành: Windows 7/8/10/Server

New Feature/Enhancement:

1. Change the mechanism that when adopting an EAP, the Controller will retain the IP configuration of EAP in Standalone mode.

2. Change the mechanism that multiple Omada Controllers can run on the same subnet.

3. Add the button of “Start Omada Controller after installation” and check it by default.

4. Extend the Max Associated Clients in Load Balance to 255.

5. Optimize the UI of Channel Utilization.

6. Optimize the authentication page of portal.

7. Optimize the UI of the portal that you cannot click Apply when you are uploading a photo.

 

Bug Fixed:

1. Fixed the bug that the page of MAC filter may not display all groups when there are more than 5 groups.

2. Fixed the bug that after deleting a site, the Voucher code and Local user of this site still exist.

3. Fixed the bug that the site configuration will fail to restore when the imported site contains same Voucher code as the current Controller.

4. Fixed the bug that when mesh AP is powered off during upgrade, Controller may fail to upgrade other APs, with a prompt message “Other APs are upgrading”.

 

Notes:

1. To use Omada Controller 3.2.X new features, you need to upgrade your EAP's firmware to the corresponding version.

2. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

3. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.X or earlier version.
Ngày Phát Hành: 2019-11-08 Ngôn Ngữ: English File Size: 99.4MB
Hệ Điều Hành: Ubuntu 14.04/16.04/17.04/18.04/Debian 9.8

New Feature/Enhancement:

1. Add “Select Page” feature on voucher management page.

2. Change default status of “Terms of Service” on default portal page to uncheck.

3. Optimize the “Free Authentication Policy” to support URL with suffixes.

4. Change the default status of new added “Free Authentication Policy” to enable.

 

Bug Fixed:

1. Fixed the bug that when clients disconnect from the Facebook portal, the connection time and traffic usage of these clients may be zero in the log.

2. Fixed the bug that AP may disconnect from Omada Controller when it is upgrading the firmware.

3. Fixed the bug that in some cases, the channel configuration of 2.4G frequency may show up in 5G by mistake.

4. Fixed the bug that the configuration of SSID will not be issued correctly when changing the WLAN Group on the provisioning status.

 

Notes:

1. To use new features on Omada Controller 3.2.X, you need to upgrade your EAP's firmware to the corresponding version.

2. The Omada Controller program needs to use the system's netstat command. If the Linux system does not have net-tools installed (which contain the netstat command), the program may not be able to run normally.

3. Support 64-bit Linux operating system including Ubuntu 14.04/16.04/17.04/18.04/Debian 9.8

4. Built-in JRE 1.8 Java environment.

5. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

6. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.8.
Ngày Phát Hành: 2019-11-08 Ngôn Ngữ: English File Size: 123.35MB
Hệ Điều Hành: Ubuntu 14.04/16.04/17.04/18.04, CentOS 6.x/7.x and Fedora 20 or above, Debian 9.8.

New Feature/Enhancement:

1. Add “Select Page” feature on the management page of vouchers.

2. Change the default status of “Terms of Service” to uncheck.

3. Optimize the “Free Authentication Policy” to support URL with suffixes.

4. Change the default status of new added “Free Authentication Policy” to enable.

 

Bug Fixed:

1. Fixed the bug that when clients disconnect from the Facebook portal, the connection time and traffic usage of these clients may be zero in the log.

2. Fixed the bug that AP may disconnect from Omada Controller when it is upgrading the firmware.

3. Fixed the bug that in some cases, the channel configuration of 2.4G frequency may show up in 5G by mistake.

4. Fixed the bug that the configuration of SSID will not be issued correctly when changing the WLAN Group on the provisioning status.

 

 

Notes:

1. To use new features on Omada Controller 3.2.x, you need to upgrade your EAP's firmware to the corresponding version.

2. The Omada Controller program needs to use the system's netstat command. If the Linux system does not have net-tools installed (which contain the netstat command), the program may not be able to run normally.

3. Support 64-bit Linux operating system including Ubuntu 14.04/16.04/17.04/18.04, CentOS 6.x/7.x and Fedora 20 or above, Debian 9.8.

4. Built-in JRE 1.8 Java environment.

5. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

6. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.8.

7. When upgrading from Controller 2.5.3 Linux to this version via install.sh, you need to uninstall old version of Controller first.
Ngày Phát Hành: 2019-11-08 Ngôn Ngữ: English File Size: 120.52MB
Hệ Điều Hành: Windows 7/8/10/Server

New Feature/Enhancement:

1. Add “Select Page” feature on the voucher management page.

2. Change the default status of “Terms of Service” on default portal page to uncheck.

3. Optimize the “Free Authentication Policy” to support URL with suffixes.

4. Change the default status of new added “Free Authentication Policy” to enable.

 

Bug Fixed:

1. Fixed the bug that when clients disconnect from the Facebook portal, the connection time and traffic usage of these clients may be zero in the log.

2. Fixed the bug that AP may disconnect from Omada Controller when it is upgrading the firmware.

3. Fixed the bug that in some cases, the channel configuration of 2.4G frequency may show up in 5G by mistake.

4. Fixed the bug that the configuration of SSID will not be issued correctly when changing the WLAN Group on the provisioning status.

 

Notes:

1. To use Omada Controller 3.2.x new features, you need to upgrade your EAP's firmware to the corresponding version.

2. Once upgraded to this version of Omada Controller, you will NOT be able to downgrade to an earlier version.

3. Portal configuration will be lost after upgrading to Omada Controller 3.2.X from 2.4.X or earlier version.

4. You are recommended to create a backup before upgrading, or you will not be permitted to install this version of Omada Controller.
Ngày Phát Hành: 2019-11-08 Ngôn Ngữ: English File Size: 124.43MB
Hệ Điều Hành: Windows 7/8/10/Server

New Feature/Enhancement:

1. Add “Select Page” feature on the voucher management page.

2. Change the default status of “Terms of Service” on default portal page to uncheck.

3. Optimize the “Free Authentication Policy” to support URL with suffixes.

4. Change the default status of new added “Free Authentication Policy” to enable.

 

Bug Fixed:

1. Fixed the bug that when clients disconnect from the Facebook portal, the connection time and traffic usage of these clients may be zero in the log.

2. Fixed the bug that AP may disconnect from Omada Controller when it is upgrading the firmware.

3. Fixed the bug that in some cases, the channel configuration of 2.4G frequency may show up in 5G by mistake.

4. Fixed the bug that the configuration of SSID will not be issued correctly when changing the WLAN Group on the provisioning status.

 

Notes:

1. To use Omada Controller 3.2.x new features, you need to upgrade your EAP's firmware to the corresponding version.

2. Once upgraded to this version of Omada Controller, you will NOT be able to downgrade to an earlier version.

3. Portal configuration will be lost after upgrading to Omada Controller 3.2.X from 2.4.X or earlier version.

4. You are recommended to create a backup before upgrading, or you will not be permitted to install this version of Omada Controller.
Ngày Phát Hành: 2019-07-26 Ngôn Ngữ: English File Size: 99.23MB
Hệ Điều Hành: Ubuntu 14.04/16.04/17.04/18.04/Debian 9.8

New Feature/Enhancement:

1. Optimize the performance of Controller to manage up to 1500 EAPs.

2. Optimize the interactive process between EAP and Controller to decrease the processing time.

3. Limit the entry number of client/client history/guest to 1.2 million/1.2 million /6 million.

4. Optimize display page of map and log when there are a lot of entries.

 

Bug Fixed:

1. Fixed the bug that CPU and memory may be highly used when Fast Roaming is enabled.

2. Fixed the bug that Omada Controller reports timeout error when adopting multiple EAPs simultaneously.

3. Fixed the bug that Controller will print all Voucher codes even only some of the codes are selected.

 

Notes:

1. To use new features on Omada Controller 3.2.X, you need to upgrade your EAP's firmware to the corresponding version.

2. The Omada Controller program needs to use the system's netstat command. If the Linux system does not have net-tools installed (which contain the netstat command), the program may not be able to run normally.

3. Support 64-bit Linux operating system including Ubuntu 14.04/16.04/17.04/18.04/Debian 9.8

4. Built-in JRE 1.8 Java environment.

5. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

6. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.8.

 
Ngày Phát Hành: 2019-07-26 Ngôn Ngữ: English File Size: 123.15MB
Hệ Điều Hành: Ubuntu 14.04/16.04/17.04/18.04, CentOS 6.x/7.x and Fedora 20 or above, Debian 9.8.

New Feature/Enhancement:

1. Optimize the performance of Controller to manage up to 1500 EAPs.

2. Optimize the interactive process between EAP and Controller to decrease the processing time.

3. Limit the entry number of client/client history/guest to 1.2 million/1.2 million /6 million.

4. Optimize display page of map and log when there are a lot of entries.

 

Bug Fixed:

1. Fixed the bug that CPU and memory may be highly used when Fast Roaming is enabled.

2. Fixed the bug that Omada Controller reports timeout error when adopting multiple EAPs simultaneously.

3. Fixed the bug that Controller will print all Voucher codes even only some of the codes are selected.

 

Notes:

1. To use new features on Omada Controller 3.2.x, you need to upgrade your EAP's firmware to the corresponding version.

2. The Omada Controller program needs to use the system's netstat command. If the Linux system does not have net-tools installed (which contain the netstat command), the program may not be able to run normally.

3. Support 64-bit Linux operating system including Ubuntu 14.04/16.04/17.04/18.04, CentOS 6.x/7.x and Fedora 20 or above, Debian 9.8.

4. Built-in JRE 1.8 Java environment.

5. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

6. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.8.

7. When upgrading from Controller 2.5.3 Linux to this version via install.sh, you need to uninstall old version of Controller first.
Ngày Phát Hành: 2019-07-04 Ngôn Ngữ: English File Size: 120.29MB
Hệ Điều Hành: Windows 7/8/10/Server

New Feature/Enhancement:

1. Optimize the performance of Controller to manage up to 1500 EAPs.

2. Optimize the interactive process between EAP and Controller to decrease the process time.

3. Limit the entry number of client/client history/guest to 1.2 million/1.2 million /6 million.

4. Optimize display page of map and log when there are a lot of entries.

 

Bug Fixed:

1. Fixed the bug that CPU and memory may be highly used when Fast Roaming is enabled.

2. Fixed the bug that Omada Controller reports timeout error when adopting multiple EAPs simultaneously.

3. Fixed the bug that Controller will print all Voucher codes even only some of the codes are selected.

 

Notes:

1. To use Omada Controller 3.2.x new features, you need to upgrade your EAP's firmware to the corresponding version.

2. Once upgraded to this version of Omada Controller, you will NOT be able to downgrade to an earlier version.

3. Portal configuration will be lost after upgrading to Omada Controller 3.2.X from 2.4.X or earlier version.
Ngày Phát Hành: 2019-07-04 Ngôn Ngữ: English File Size: 124.2MB
Hệ Điều Hành: Windows 7/8/10/Server

New Feature/Enhancement:

1. Optimize the performance of Controller to manage up to 1500 EAPs.

2. Optimize the interactive process between EAP and Controller to decrease the process time.

3. Limit the entry number of client/client history/guest to 1.2 million/1.2 million /6 million.

4. Optimize display page of map and log when there are a lot of entries.

 

Bug Fixed:

1. Fixed the bug that CPU and memory may be highly used when Fast Roaming is enabled.

2. Fixed the bug that Omada Controller reports timeout error when adopting multiple EAPs simultaneously.

3. Fixed the bug that Controller will print all Voucher codes even only some of the codes are selected.

 

Notes:

1. To use Omada Controller 3.2.x new features, you need to upgrade your EAP's firmware to the corresponding version.

2. Once upgraded to this version of Omada Controller, you will NOT be able to downgrade to an earlier version.

3. Portal configuration will be lost after upgrading to Omada Controller 3.2.X from 2.4.X or earlier version.
Ngày Phát Hành: 2019-03-08 Ngôn Ngữ: English File Size: 123.6MB
Hệ Điều Hành: Windows 7/8/10/Server

New Feature/Enhancement:

1. Merge 2.4GHz and 5GHz SSID.

2. Add Guest Network function.

3. Optimize log field and content.

4. Add SSID Radius accounting to WPA-Enterprise security mode.

5. Optimize the site list which allows us to inquire the specific site based on the site name and add new entrance for the hotspot.

6. Add SSL encryption in Log Server, and Log setting/Mail Server can be only accessed by administrator account.

7. Add Layer-3 Accessibility in SSH.

8. Add Mesh settings to Backup and Restore file.

9. Add CHAP encryption and NAS ID in Radius portal authentication and the Radius Client role is transferred from EAP to Omada Controller.

10. Add SSID MAC Authentication to none security mode.

11. Add channel utilization function.

12. Add Full-Sector DFS function in Mesh network.

13. Channel limit is revised from private configuration to site settings.

14. Support inputting domain name in SMTP server.

 

Notes:

1. The log will be cleared when you upgrade the software from version 3.0.x to version 3.1.4.

2. Add push notification to Omada APP of version 2.1.4 or above when EAP is connected/disconnected from Omada Controller.

3. This version of Omada Controller is applied to Omada APP of version 2.1.4 or above.

4. When you upgrade your controller or backup files from lower version, the 2.4GHz and 5GHz SSID entries with the same name will be merged and it will inherit the parameters of the original 2.4GHz SSID.

5. If you use External Radius Server with External Web Portal in old version controller, pay attention that the API has been changed in this version, thus you have to modify your External Web Portal, refer to FAQ-2390 for more details.

6. The log generated by EAP will be managed and storaged by Controller if you manage EAPs by Omada Controller.

7. Channel utilization will take effect only with new firmware.
Ngày Phát Hành: 2019-03-08 Ngôn Ngữ: English File Size: 127.5MB
Hệ Điều Hành: Windows 7/8/10/Server

New Feature/Enhancement:

1. Merge 2.4GHz and 5GHz SSID.

2. Add Guest Network function.

3. Optimize log field and content.

4. Add SSID Radius accounting to WPA-Enterprise security mode.

5. Optimize the site list which allows us to inquire the specific site based on the site name and add new entrance for the hotspot.

6. Add SSL encryption in Log Server, and Log setting/Mail Server can be only accessed by administrator account.

7. Add Layer-3 Accessibility in SSH.

8. Add Mesh settings to Backup and Restore file.

9. Add CHAP encryption and NAS ID in Radius portal authentication and the Radius Client role is transferred from EAP to Omada Controller.

10. Add SSID MAC Authentication to none security mode.

11. Add channel utilization function.

12. Add Full-Sector DFS function in Mesh network.

13. Channel limit is revised from private configuration to site settings.

14. Support inputting domain name in SMTP server.

 

Notes:

1. The log will be cleared when you upgrade the software from version 3.0.x to version 3.1.4.

2. Add push notification to Omada APP of version 2.1.4 or above when EAP is connected/disconnected from Omada Controller.

3. This version of Omada Controller is applied to Omada APP of version 2.1.4 or above.

4. When you upgrade your controller or backup files from lower version, the 2.4GHz and 5GHz SSID entries with the same name will be merged and it will inherit the parameters of the original 2.4GHz SSID.

5. If you use External Radius Server with External Web Portal in old version controller, pay attention that the API has been changed in this version, thus you have to modify your External Web Portal, refer to FAQ-2390 for more details.

6. The log generated by EAP will be managed and storaged by Controller if you manage EAPs by Omada Controller.

7. Channel utilization will take effect only with new firmware.

EAP Discovery Tool

The EAP Discovery Tool can help the EAP Controller to adopt the EAP in L3 Network, and you can also use the EAP Discovery Tool to find the EAP’s IP address.

Ngày Phát Hành: 2019-08-06 Ngôn Ngữ: English File Size: 25.85 MB
Hệ Điều Hành: WinXP/Vista/7/8/8.1/10/Server2008/Server2012/Mac OS X 10.7/10.8/10.9/10.10/10.11

Bug fixed:

1. Fixed the bug that the Discovery Utility may fail to find EAPs.

2. Fixed the bug that the Cancel button may overlap with the display box after managing APs.

 

Note:

1. This version of software can be used in both Windows and Mac operation system.

2. Double click the software or run the command “java –jar **.jar” to run the software on MacOS (**.jar is the name of this software).

3. To run this software, you need to install JRE 8.0 on your PC first.
Ngày Phát Hành: 2019-06-14 Ngôn Ngữ: English File Size: 23.54 MB
Hệ Điều Hành: WinXP/Vista/7/8/8.1/10/Server2008/Server2012/Mac OS X 10.7/10.8/10.9/10.10/10.11

Bug fixed:

1. Fixed the bug that when the Discovery Utility issues Controller_IP to EAPs which are in factory status, Controller cannot batch manage the EAPs.

2. Fixed the bug that sometimes the Discovery Utility cannot find all EAPs when running in MacOS.

Note:

1. This version of software can be used in both Windows and Mac operation system.

2. Double click the software or run the command “java –jar **.jar” to run the software on MacOS(**.jar is the name of this software).

3. To run this software, you need to install JRE 8.0 on your PC.
Ngày Phát Hành: 2018-07-24 Ngôn Ngữ: English File Size: 84.16 MB
Hệ Điều Hành: Mac OS X 10.7/10.8/10.9/10.10/10.11

New Feature/Enhancement:
1. Change name to "Omada Discovery Utility".
2. Update background picture during installation.
3. Limit the maximum length of controller hostname to 79.
 
Bug Fixed:
Fix the bug that searching in the search box will cause the software to hang.
 
Note:
Operating System: Mac OS X 10.7/10.8/10.9/10.10/10.11.
Ngày Phát Hành: 2016-11-08 Ngôn Ngữ: English File Size: 3.39MB
Hệ Điều Hành: WinXP/Vista/7/8/8.1/10/Server2008/Server2012

Modifications and Bug Fixes:

The first Discovery Utility released.

Notes:

For EAP series, including EAP110, EAP115, EAP120, EAP220, EAP320, EAP330,EAP245,etc.

Apps

Omada APP

TP-Link Omada lets you configure settings, monitor network status and manage clients, all from the convenience of a smart phone or tablet. Learn more about Compatible Devices.

Note: To use Omada, please update your EAP's firmware to the latest version.

GPL Code

Emulators

Phiên Bản Firmware
Working Mode
Ngôn Ngữ
180420(EU)
-
English

Feature Filter: Tất Cả EAP AdoptionPortalManagementQuick StartConfigurationConfiguration Example

Q&A

Feature Configuration Guide

T2700G-28TQ License Download
License Model: T2700G-28TQ-L1000

Find your product MAC and Serial Number.
License Key:
Product Serial Number:
Product MAC:
Checking code:

SubscriptionTP-Link takes your privacy seriously. For further details on TP-Link's privacy practices, see TP-Link's Privacy Policy.

Follow Us

Về chúng tôi
Tin Tức
Mua ở đâu
Learning Center
Vietnam / Tiếng Việt Nam
Công Ty TNHH Công Nghệ TP-Link Bản Quyền 2020. Bảo Lưu Mọi Quyền