設定影片

  • How to manage TP-Link EAPs centrally via the Software Controller

    This video demonstrates how to manage TP-Link EAPs centrally via the Software Controller. The setup consists of three steps:
    • Install the Software
    • Configure Discovery Utility (If your EAPs and the Controller Host are on different subnets)
    • Configure Software Controller

    THIS VIDEO APPLIES TO:
    • All TP-Link EAP models (except EAP120 and EAP220)
    • Omada Software Controller
    • Mass EAPs (usually more than three)

    Learn More

  • How to set up a TP Link EAP via your mobile phone

    This video demonstrates how to set up a TP-Link EAP via your mobile phone. The setup consists of four steps:
    • Connect the EAP to the network
    • Download the Omada APP
    • Connect to the EAP's wireless network
    • Set up the EAP using the Omada APP

    THIS VIDEO APPLIES TO:
    • All TP-Link EAP models. (except EAP120 and EAP220)
    • A small number (1-3) of EAPs.

    Learn More

  • How to setup the OC200 via a web browser

    This video will demonstrate how to set up the OC200 via a web browser. The setup consists of six steps:
    • Connect the OC200 to your local network.
    • Get ready for setup.
    • Create a TP-Link ID.
    • Log into your TP-Link ID.
    • Add the OC200 to your TP-Link ID.
    • Follow the wizard to set up the OC200.

    THIS VIDEO APPLIES TO:
    • All TP-Link EAP models (except EAP120 and EAP220)
    • Omada Cloud Controller OC200
    • Mass EAPs (usually more than three)

    Learn More

  • How to setup the OC200 via your mobile phone

    This video will demonstrate how to set up the OC200 via your mobile phone. You need to use the Omada APP to complete the setup. The setup consists of six steps:
    • Connect the OC200 to your local network.
    • Get ready for setup.
    • Create a TP-Link ID.
    • Log into your TP-Link ID.
    • Add the OC200 to your TP-Link ID.
    • Follow the wizard to set up the OC200.
    THIS VIDEO APPLIES TO:
    • All TP-Link EAP models (except EAP120 and EAP220)
    • Omada Cloud Controller OC200
    • Mass EAPs (usually more than three)

    Learn More

  • How to manage TP-Link EAPs centrally from a remote place via a web browser

    You can manage TP-Link EAPs at any time from anywhere with the Cloud Access function of our Omada Controller Software. This video introduces both the application scenario and concrete steps you can follow. Don't hesitate to give it a try.
    THIS VIDEO APPLIES TO:
    • All TP-Link EAP models (except EAP120 and EAP220)
    • Omada Controller Software (version 3.0.2 or above)
    • Mass EAPs (usually more than three)

    Learn More

  • A Quick Overview of EAP Management Methods

    This video introduces how to choose the optimum method to manage TP-Link EAPs in your scenario.
    Here are 3 most common scenarios and their corresponding methods:
    • Manage 1 or 2 EAPs locally
    • Manage 3 or more EAPs locally
    • Manage 3 or more EAPs remotely
    When choosing the method, consider the following questions:
    1. Standalone Mode or Controller Mode?
    2. In Controller mode, what kind of controller will you use, an OC200 or a PC with Omada Software Controller?
    3. What kind of user interface will you use, a web browser or the Omada app?

    Learn More

  • How to Set up a TP-Link EAP via Web browser

    This video will demonstrate how to set up a TP-Link EAP via a web browser. The setup consists of three steps:
    1. Connect the EAP to the network
    2. Log into the EAP (via a wired/wireless connection)
    3. Change the default SSID
    This video is suitable for users with a small number (1-3) of EAPs .

    Learn More

常見問題

韌體

韌體更新可以解決前版韌體可能有的一些問題並改善它目前的效能。

若要更新

重要:若要防止韌體升級失敗,請在繼續在升級程序前閱讀以下內容

  • 請在您購買地點的當地官方網站下載韌體並對您的TP-Link設備進行升級,否則將違反保固條款。如果有需要,請點選 這裡 以變更網站。
  • 為了合適的韌體版本,請確認您設備目前的硬體版本。錯誤的韌體更新可能會損壞您的設備並使保固失效。( 一般來說,V1.x=V1)
  • 非常重要,更韌體升級期間請勿關閉設備的電源, 因為這很可能會導致產品的永久性損壞。
  • 除非在TP-Link設備沒有LAN/Ethernet連接埠的狀況下,否則請不要使用無線連接更新韌體。對於LTE-MiFi,建議您透過USB連接埠進行升級。
  • 建議您停止電腦上所有的網際網路應用程式,或在升級前簡單地中斷網際網路線路即可。
  • 在升級前請使用解壓縮軟體,例如:WinZIP 或 WinRAR 解壓縮您下載的檔案。
EAP110-Outdoor(US)_V3_3.3.0 Build 20190301
發佈日期: 2019-04-23 語言: 英語 檔案大小: 5.70 MB

Recommended Controller Software Version: Omada Controller v3.1.x or above

 

New Feature/Enhancement:

1. Add Radius Accounting to External Radius Server in standalone mode.

2. Add SSID Radius accounting to WPA-Enterprise security mode.

3. Add SSL encryption in Auto Mail of Log Settings.

4. Support the feature of merging 2.4GHz and 5GHz SSID with Controller 3.1.4.

5. Support SSID MAC Authentication to none security mode with Controller 3.1.4.

6. Support channel utilization function with Controller 3.1.4.

7. Support Layer-3 Accessibility in SSH with Controller 3.1.4.

8. Change the rule of the LED when resetting/rebooting EAP.

 

Notes:

1. For EAP110-Outdoor_V3 only.

2. Your device's configuration won't be lost after upgrading.

3. This version of firmware is applied to Omada APP of version 2.1.X or above.

EAP110-Outdoor(US)_V3_3.2.0 Build 20181113
發佈日期: 2018-12-11 語言: 英語 檔案大小: 7.12 MB

Recommended Controller Software Version:  Omada Controller v3.0.x or above

 

New Feature/Enhancement:

1. Add Band Steering/LED Locate/Client rate limit/SSID rate limit Function in Standalone mode.

2. Add More Client Detail Log in standalone mode.

3. The SSID isolation function is promoted to the Guest Network Function. Wireless Clients connected with Guest SSID can’t communicate with each other and the local network.

4. UI optimization

5. Change the HTTP port of Portal authentication page from 80 to 22080 in standalone mode.

 

Bug Fixed:

1. Fixed the bug that HTTPS redirection of Portal authentication page will be inoperative when Omada Controller and Omada EAP belong to different subnet.

2. Fixed the bug that we may fail to change the configuration of portal function in standalone mode, if we uncheck Term of Use function in portal configuration page.

3. Fixed the bug that HTTPS redirection of Portal authentication page will be inoperative when the IP address of Omada EAP and wireless clients belong to different subnet.

 

Notes:

1. For EAP110-Outdoor_V3 only.

2. Your device's configuration won't be lost after upgrading.

 

EAP110-Outdoor(US)_V3_3.1.0 Build 20180418
發佈日期: 2018-04-28 語言: 英語 檔案大小: 7.06 MB

Recommended Controller Software Version:  Omada Controller v 2.6.x or above

 

New Features/Improvements:

1. Support Omada APP management method.

2. Management mechanism changing: In standalone mode, only one user is allowed to login the management page of the EAP at the same time.

3. Supports HTTPS redirection of portal authentication page.

4. Facebook Portal now intercepts HTTPS access unless you pass the authentication.

5. Omada Controller will create Free Authentication Policy for the External Web Portal Server   and External Portal Server automatically.

6. Supports rate limit function for a single client. (If you have set SSID, Client, Voucher rate limit at the same time, and the minimum limit value will take effect.)

7. Restricts local resources access of wireless clients which did not pass the authentication.

8. Decreased the synchronization update time of Omada Controller when the IP address of EAP is changed.

9. EAP will report Client RSSI information to Omada Controller.

10. Optimized Rouge AP detection process.

11. Changed the selecting range of auto channel of 2.4G radio to non-overlapping channel 1/6/11

 

Bug Fixed:

1. Fixed the incorrect IP address displaying of some clients in Omada Controller.

2. Fixed the bug that clients may still be able to connect with EAP after blocking the clients in clients list.

3. Fixed the bug that SSID rate limit configuration may not take effect if it is configured when wireless radio is turned off.

 

Notes:

1. For EAP110-Outdoor (US)_V3 only.

2. If you managed EAP by Omada Controller, you can’t manage this EAP by Web management page, unless you have reset the EAP.

3. Your device's configuration won't be lost after upgrading.

若要在TP-Link產品上使用第三方韌體

一些TP-Link產品的官方韌體可以被第三方韌體替換,例如:DD-WRT。TP-Link沒有義務提供任何維護或支持,也不保證第三方固件的性能和穩定性。使用第三方韌體後,將使產品的保固失效。

供程式人員的開放原始碼(GPL)

請注意:TP-Link的產品部分包含由第三方開發的程式碼,包括:受GNU通用公共許可證(“GPL”),版本1 /版本2 /版本3或GNU較寬鬆通用公共許可證(“LGPL”)制約的程式碼。您可以使用相應的軟體條件來遵循GPL許可條款。

在此您可以查看、列印與下載對應的GPL許可條款。 您將收到TP-Link產品中用於直接下載的相關軟件的GPL原始以及進一步的資訊,包含在GPL碼中心下包含GPL程式碼的TP-Link軟體列表。

各自的程序分發沒有任何擔保; 甚至沒有對適銷性或特定用途的適用性的暗示保證。請參閱各自的GNU通用公共許可證了解更多詳情。

管理軟體

EAP控制器用於集中管理多個EAP。

發佈日期: 2020-01-16 語言: 英語 檔案大小: 123.35MB
作業系統: Ubuntu 14.04/16.04/17.04/18.04, CentOS 6.x/7.x and Fedora 20 or above, Debian 9.8.

New Feature/Enhancement:

1. Change the mechanism that when adopting an EAP, the Controller will retain the IP configuration of EAP in Standalone mode.

2. Change the mechanism that multiple Omada Controllers can run on the same subnet.

3. Add the button of “Start Omada Controller after installation” and check it by default.

4. Extend the Max Associated Clients in Load Balance to 255.

5. Optimize the UI of Channel Utilization.

6. Optimize the authentication page of portal.

7. Optimize the UI of the portal that you cannot click Apply when you are uploading a photo.

8. Optimize the External Portal Server to support URL with parameters.

 

Bug Fixed:

1. Fixed the bug that the page of MAC filter may not display all groups when there are more than 5 groups.

2. Fixed the bug that after deleting a site, the Voucher code and Local user of this site still exist.

3. Fixed the bug that the site configuration will fail to restore when the imported site contains same Voucher code as the current Controller.

4. Fixed the bug that when mesh AP is powered off during upgrade, Controller may fail to upgrade other APs, with a prompt message “Other APs are upgrading”.

 

Notes:

1. To use new features on Omada Controller 3.2.x, you need to upgrade your EAP's firmware to the corresponding version.

2. The Omada Controller program needs to use the system's netstat command. If the Linux system does not have net-tools installed (which contain the netstat command), the program may not be able to run normally.

3. Support 64-bit Linux operating system including Ubuntu 14.04/16.04/17.04/18.04, CentOS 6.x/7.x and Fedora 20 or above, Debian 9.8.

4. Built-in JRE 1.8 Java environment.

5. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

6. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.8.

7. When upgrading from Controller 2.5.3 Linux to this version via install.sh, you need to uninstall old version of Controller first.

 

發佈日期: 2020-01-16 語言: 英語 檔案大小: 99.4MB
作業系統: Ubuntu 14.04/16.04/17.04/18.04/Debian 9.8

New Feature/Enhancement:

1. Change the mechanism that when adopting an EAP, the Controller will retain the IP configuration of EAP in Standalone mode.

2. Change the mechanism that multiple Omada Controllers can run on the same subnet.

3. Add the button of “Start Omada Controller after installation” and check it by default.

4. Extend the Max Associated Clients in Load Balance to 255.

5. Optimize the UI of Channel Utilization.

6. Optimize the authentication page of portal.

7. Optimize the UI of the portal that you cannot click Apply when you are uploading a photo.

8. Optimize the External Portal Server to support URL with parameters.

 

Bug Fixed:

1. Fixed the bug that the page of MAC filter may not display all groups when there are more than 5 groups.

2. Fixed the bug that after deleting a site, the Voucher code and Local user of this site still exist.

3. Fixed the bug that the site configuration will fail to restore when the imported site contains same Voucher code as the current Controller.

4. Fixed the bug that when mesh AP is powered off during upgrade, Controller may fail to upgrade other APs, with a prompt message “Other APs are upgrading”.

 

Notes:

1. To use new features on Omada Controller 3.2.X, you need to upgrade your EAP's firmware to the corresponding version.

2. The Omada Controller program needs to use the system's netstat command. If the Linux system does not have net-tools installed (which contain the netstat command), the program may not be able to run normally.

3. Support 64-bit Linux operating system including Ubuntu 14.04/16.04/17.04/18.04/Debian 9.8

4. Built-in JRE 1.8 Java environment.

5. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

6. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.8.

發佈日期: 2020-01-09 語言: 英語 檔案大小: 120.53MB
作業系統: Windows 7/8/10/Server

New Feature/Enhancement:

1. Change the mechanism that when adopting an EAP, the Controller will retain the IP configuration of EAP in Standalone mode.

2. Change the mechanism that multiple Omada Controllers can run on the same subnet.

3. Add the button of “Start Omada Controller after installation” and check it by default.

4. Extend the Max Associated Clients in Load Balance to 255.

5. Optimize the UI of Channel Utilization.

6. Optimize the authentication page of portal.

7. Optimize the UI of the portal that you cannot click Apply when you are uploading a photo.

 

Bug Fixed:

1. Fixed the bug that the page of MAC filter may not display all groups when there are more than 5 groups.

2. Fixed the bug that after deleting a site, the Voucher code and Local user of this site still exist.

3. Fixed the bug that the site configuration will fail to restore when the imported site contains same Voucher code as the current Controller.

4. Fixed the bug that when mesh AP is powered off during upgrade, Controller may fail to upgrade other APs, with a prompt message “Other APs are upgrading”.

 

Notes:

1. To use Omada Controller 3.2.X new features, you need to upgrade your EAP's firmware to the corresponding version.

2. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

3. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.X or earlier version.

發佈日期: 2020-01-09 語言: 英語 檔案大小: 124.44MB
作業系統: Windows 7/8/10/Server

New Feature/Enhancement:

1. Change the mechanism that when adopting an EAP, the Controller will retain the IP configuration of EAP in Standalone mode.

2. Change the mechanism that multiple Omada Controllers can run on the same subnet.

3. Add the button of “Start Omada Controller after installation” and check it by default.

4. Extend the Max Associated Clients in Load Balance to 255.

5. Optimize the UI of Channel Utilization.

6. Optimize the authentication page of portal.

7. Optimize the UI of the portal that you cannot click Apply when you are uploading a photo.

 

Bug Fixed:

1. Fixed the bug that the page of MAC filter may not display all groups when there are more than 5 groups.

2. Fixed the bug that after deleting a site, the Voucher code and Local user of this site still exist.

3. Fixed the bug that the site configuration will fail to restore when the imported site contains same Voucher code as the current Controller.

4. Fixed the bug that when mesh AP is powered off during upgrade, Controller may fail to upgrade other APs, with a prompt message “Other APs are upgrading”.

 

Notes:

1. To use Omada Controller 3.2.X new features, you need to upgrade your EAP's firmware to the corresponding version.

2. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

3. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.X or earlier version.

發佈日期: 2019-11-08 語言: 英語 檔案大小: 99.4MB
作業系統: Ubuntu 14.04/16.04/17.04/18.04/Debian 9.8

New Feature/Enhancement:

1. Add “Select Page” feature on voucher management page.

2. Change default status of “Terms of Service” on default portal page to uncheck.

3. Optimize the “Free Authentication Policy” to support URL with suffixes.

4. Change the default status of new added “Free Authentication Policy” to enable.

 

Bug Fixed:

1. Fixed the bug that when clients disconnect from the Facebook portal, the connection time and traffic usage of these clients may be zero in the log.

2. Fixed the bug that AP may disconnect from Omada Controller when it is upgrading the firmware.

3. Fixed the bug that in some cases, the channel configuration of 2.4G frequency may show up in 5G by mistake.

4. Fixed the bug that the configuration of SSID will not be issued correctly when changing the WLAN Group on the provisioning status.

 

Notes:

1. To use new features on Omada Controller 3.2.X, you need to upgrade your EAP's firmware to the corresponding version.

2. The Omada Controller program needs to use the system's netstat command. If the Linux system does not have net-tools installed (which contain the netstat command), the program may not be able to run normally.

3. Support 64-bit Linux operating system including Ubuntu 14.04/16.04/17.04/18.04/Debian 9.8

4. Built-in JRE 1.8 Java environment.

5. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

6. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.8.

發佈日期: 2019-11-08 語言: 英語 檔案大小: 123.35MB
作業系統: Ubuntu 14.04/16.04/17.04/18.04, CentOS 6.x/7.x and Fedora 20 or above, Debian 9.8.

New Feature/Enhancement:

1. Add “Select Page” feature on the management page of vouchers.

2. Change the default status of “Terms of Service” to uncheck.

3. Optimize the “Free Authentication Policy” to support URL with suffixes.

4. Change the default status of new added “Free Authentication Policy” to enable.

 

Bug Fixed:

1. Fixed the bug that when clients disconnect from the Facebook portal, the connection time and traffic usage of these clients may be zero in the log.

2. Fixed the bug that AP may disconnect from Omada Controller when it is upgrading the firmware.

3. Fixed the bug that in some cases, the channel configuration of 2.4G frequency may show up in 5G by mistake.

4. Fixed the bug that the configuration of SSID will not be issued correctly when changing the WLAN Group on the provisioning status.

 

 

Notes:

1. To use new features on Omada Controller 3.2.x, you need to upgrade your EAP's firmware to the corresponding version.

2. The Omada Controller program needs to use the system's netstat command. If the Linux system does not have net-tools installed (which contain the netstat command), the program may not be able to run normally.

3. Support 64-bit Linux operating system including Ubuntu 14.04/16.04/17.04/18.04, CentOS 6.x/7.x and Fedora 20 or above, Debian 9.8.

4. Built-in JRE 1.8 Java environment.

5. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

6. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.8.

7. When upgrading from Controller 2.5.3 Linux to this version via install.sh, you need to uninstall old version of Controller first.

發佈日期: 2019-11-08 語言: 英語 檔案大小: 120.52MB
作業系統: Windows 7/8/10/Server

New Feature/Enhancement:

1. Add “Select Page” feature on the voucher management page.

2. Change the default status of “Terms of Service” on default portal page to uncheck.

3. Optimize the “Free Authentication Policy” to support URL with suffixes.

4. Change the default status of new added “Free Authentication Policy” to enable.

 

Bug Fixed:

1. Fixed the bug that when clients disconnect from the Facebook portal, the connection time and traffic usage of these clients may be zero in the log.

2. Fixed the bug that AP may disconnect from Omada Controller when it is upgrading the firmware.

3. Fixed the bug that in some cases, the channel configuration of 2.4G frequency may show up in 5G by mistake.

4. Fixed the bug that the configuration of SSID will not be issued correctly when changing the WLAN Group on the provisioning status.

 

Notes:

1. To use Omada Controller 3.2.x new features, you need to upgrade your EAP's firmware to the corresponding version.

2. Once upgraded to this version of Omada Controller, you will NOT be able to downgrade to an earlier version.

3. Portal configuration will be lost after upgrading to Omada Controller 3.2.X from 2.4.X or earlier version.

4. You are recommended to create a backup before upgrading, or you will not be permitted to install this version of Omada Controller.

發佈日期: 2019-11-08 語言: 英語 檔案大小: 124.43MB
作業系統: Windows 7/8/10/Server

New Feature/Enhancement:

1. Add “Select Page” feature on the voucher management page.

2. Change the default status of “Terms of Service” on default portal page to uncheck.

3. Optimize the “Free Authentication Policy” to support URL with suffixes.

4. Change the default status of new added “Free Authentication Policy” to enable.

 

Bug Fixed:

1. Fixed the bug that when clients disconnect from the Facebook portal, the connection time and traffic usage of these clients may be zero in the log.

2. Fixed the bug that AP may disconnect from Omada Controller when it is upgrading the firmware.

3. Fixed the bug that in some cases, the channel configuration of 2.4G frequency may show up in 5G by mistake.

4. Fixed the bug that the configuration of SSID will not be issued correctly when changing the WLAN Group on the provisioning status.

 

Notes:

1. To use Omada Controller 3.2.x new features, you need to upgrade your EAP's firmware to the corresponding version.

2. Once upgraded to this version of Omada Controller, you will NOT be able to downgrade to an earlier version.

3. Portal configuration will be lost after upgrading to Omada Controller 3.2.X from 2.4.X or earlier version.

4. You are recommended to create a backup before upgrading, or you will not be permitted to install this version of Omada Controller.

發佈日期: 2019-07-26 語言: 英語 檔案大小: 99.23MB
作業系統: Ubuntu 14.04/16.04/17.04/18.04/Debian 9.8

New Feature/Enhancement:

1. Optimize the performance of Controller to manage up to 1500 EAPs.

2. Optimize the interactive process between EAP and Controller to decrease the processing time.

3. Limit the entry number of client/client history/guest to 1.2 million/1.2 million /6 million.

4. Optimize display page of map and log when there are a lot of entries.

 

Bug Fixed:

1. Fixed the bug that CPU and memory may be highly used when Fast Roaming is enabled.

2. Fixed the bug that Omada Controller reports timeout error when adopting multiple EAPs simultaneously.

3. Fixed the bug that Controller will print all Voucher codes even only some of the codes are selected.

 

Notes:

1. To use new features on Omada Controller 3.2.X, you need to upgrade your EAP's firmware to the corresponding version.

2. The Omada Controller program needs to use the system's netstat command. If the Linux system does not have net-tools installed (which contain the netstat command), the program may not be able to run normally.

3. Support 64-bit Linux operating system including Ubuntu 14.04/16.04/17.04/18.04/Debian 9.8

4. Built-in JRE 1.8 Java environment.

5. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

6. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.8.

 

發佈日期: 2019-07-26 語言: 英語 檔案大小: 123.15MB
作業系統: Ubuntu 14.04/16.04/17.04/18.04, CentOS 6.x/7.x and Fedora 20 or above, Debian 9.8.

New Feature/Enhancement:

1. Optimize the performance of Controller to manage up to 1500 EAPs.

2. Optimize the interactive process between EAP and Controller to decrease the processing time.

3. Limit the entry number of client/client history/guest to 1.2 million/1.2 million /6 million.

4. Optimize display page of map and log when there are a lot of entries.

 

Bug Fixed:

1. Fixed the bug that CPU and memory may be highly used when Fast Roaming is enabled.

2. Fixed the bug that Omada Controller reports timeout error when adopting multiple EAPs simultaneously.

3. Fixed the bug that Controller will print all Voucher codes even only some of the codes are selected.

 

Notes:

1. To use new features on Omada Controller 3.2.x, you need to upgrade your EAP's firmware to the corresponding version.

2. The Omada Controller program needs to use the system's netstat command. If the Linux system does not have net-tools installed (which contain the netstat command), the program may not be able to run normally.

3. Support 64-bit Linux operating system including Ubuntu 14.04/16.04/17.04/18.04, CentOS 6.x/7.x and Fedora 20 or above, Debian 9.8.

4. Built-in JRE 1.8 Java environment.

5. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

6. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.8.

7. When upgrading from Controller 2.5.3 Linux to this version via install.sh, you need to uninstall old version of Controller first.

發佈日期: 2019-07-04 語言: 英語 檔案大小: 120.29MB
作業系統: Windows 7/8/10/Server

New Feature/Enhancement:

1. Optimize the performance of Controller to manage up to 1500 EAPs.

2. Optimize the interactive process between EAP and Controller to decrease the process time.

3. Limit the entry number of client/client history/guest to 1.2 million/1.2 million /6 million.

4. Optimize display page of map and log when there are a lot of entries.

 

Bug Fixed:

1. Fixed the bug that CPU and memory may be highly used when Fast Roaming is enabled.

2. Fixed the bug that Omada Controller reports timeout error when adopting multiple EAPs simultaneously.

3. Fixed the bug that Controller will print all Voucher codes even only some of the codes are selected.

 

Notes:

1. To use Omada Controller 3.2.x new features, you need to upgrade your EAP's firmware to the corresponding version.

2. Once upgraded to this version of Omada Controller, you will NOT be able to downgrade to an earlier version.

3. Portal configuration will be lost after upgrading to Omada Controller 3.2.X from 2.4.X or earlier version.

發佈日期: 2019-07-04 語言: 英語 檔案大小: 124.2MB
作業系統: Windows 7/8/10/Server

New Feature/Enhancement:

1. Optimize the performance of Controller to manage up to 1500 EAPs.

2. Optimize the interactive process between EAP and Controller to decrease the process time.

3. Limit the entry number of client/client history/guest to 1.2 million/1.2 million /6 million.

4. Optimize display page of map and log when there are a lot of entries.

 

Bug Fixed:

1. Fixed the bug that CPU and memory may be highly used when Fast Roaming is enabled.

2. Fixed the bug that Omada Controller reports timeout error when adopting multiple EAPs simultaneously.

3. Fixed the bug that Controller will print all Voucher codes even only some of the codes are selected.

 

Notes:

1. To use Omada Controller 3.2.x new features, you need to upgrade your EAP's firmware to the corresponding version.

2. Once upgraded to this version of Omada Controller, you will NOT be able to downgrade to an earlier version.

3. Portal configuration will be lost after upgrading to Omada Controller 3.2.X from 2.4.X or earlier version.

發佈日期: 2019-03-08 語言: 英語 檔案大小: 123.6MB
作業系統: Windows 7/8/10/Server

New Feature/Enhancement:

1. Merge 2.4GHz and 5GHz SSID.

2. Add Guest Network function.

3. Optimize log field and content.

4. Add SSID Radius accounting to WPA-Enterprise security mode.

5. Optimize the site list which allows us to inquire the specific site based on the site name and add new entrance for the hotspot.

6. Add SSL encryption in Log Server, and Log setting/Mail Server can be only accessed by administrator account.

7. Add Layer-3 Accessibility in SSH.

8. Add Mesh settings to Backup and Restore file.

9. Add CHAP encryption and NAS ID in Radius portal authentication and the Radius Client role is transferred from EAP to Omada Controller.

10. Add SSID MAC Authentication to none security mode.

11. Add channel utilization function.

12. Add Full-Sector DFS function in Mesh network.

13. Channel limit is revised from private configuration to site settings.

14. Support inputting domain name in SMTP server.

 

Notes:

1. The log will be cleared when you upgrade the software from version 3.0.x to version 3.1.4.

2. Add push notification to Omada APP of version 2.1.4 or above when EAP is connected/disconnected from Omada Controller.

3. This version of Omada Controller is applied to Omada APP of version 2.1.4 or above.

4. When you upgrade your controller or backup files from lower version, the 2.4GHz and 5GHz SSID entries with the same name will be merged and it will inherit the parameters of the original 2.4GHz SSID.

5. If you use External Radius Server with External Web Portal in old version controller, pay attention that the API has been changed in this version, thus you have to modify your External Web Portal, refer to FAQ-2390 for more details.

6. The log generated by EAP will be managed and storaged by Controller if you manage EAPs by Omada Controller.

7. Channel utilization will take effect only with new firmware.

發佈日期: 2019-03-08 語言: 英語 檔案大小: 127.5MB
作業系統: Windows 7/8/10/Server

New Feature/Enhancement:

1. Merge 2.4GHz and 5GHz SSID.

2. Add Guest Network function.

3. Optimize log field and content.

4. Add SSID Radius accounting to WPA-Enterprise security mode.

5. Optimize the site list which allows us to inquire the specific site based on the site name and add new entrance for the hotspot.

6. Add SSL encryption in Log Server, and Log setting/Mail Server can be only accessed by administrator account.

7. Add Layer-3 Accessibility in SSH.

8. Add Mesh settings to Backup and Restore file.

9. Add CHAP encryption and NAS ID in Radius portal authentication and the Radius Client role is transferred from EAP to Omada Controller.

10. Add SSID MAC Authentication to none security mode.

11. Add channel utilization function.

12. Add Full-Sector DFS function in Mesh network.

13. Channel limit is revised from private configuration to site settings.

14. Support inputting domain name in SMTP server.

 

Notes:

1. The log will be cleared when you upgrade the software from version 3.0.x to version 3.1.4.

2. Add push notification to Omada APP of version 2.1.4 or above when EAP is connected/disconnected from Omada Controller.

3. This version of Omada Controller is applied to Omada APP of version 2.1.4 or above.

4. When you upgrade your controller or backup files from lower version, the 2.4GHz and 5GHz SSID entries with the same name will be merged and it will inherit the parameters of the original 2.4GHz SSID.

5. If you use External Radius Server with External Web Portal in old version controller, pay attention that the API has been changed in this version, thus you have to modify your External Web Portal, refer to FAQ-2390 for more details.

6. The log generated by EAP will be managed and storaged by Controller if you manage EAPs by Omada Controller.

7. Channel utilization will take effect only with new firmware.

EAP發現工具

EAP發現工具可以幫助EAP控制器在L3網路中採用EAP,您還可以使用EAP發現工具尋找EAP的IP地址。

發佈日期: 2019-08-06 語言: 英語 檔案大小: 25.85 MB
作業系統: WinXP/Vista/7/8/8.1/10/Server2008/Server2012/Mac OS X 10.7/10.8/10.9/10.10/10.11

Bug fixed:

1. Fixed the bug that the Discovery Utility may fail to find EAPs.

2. Fixed the bug that the Cancel button may overlap with the display box after managing APs.

 

Note:

1. This version of software can be used in both Windows and Mac operation system.

2. Double click the software or run the command “java –jar **.jar” to run the software on MacOS (**.jar is the name of this software).

3. To run this software, you need to install JRE 8.0 on your PC first.

發佈日期: 2019-06-14 語言: 英語 檔案大小: 23.54 MB
作業系統: WinXP/Vista/7/8/8.1/10/Server2008/Server2012/Mac OS X 10.7/10.8/10.9/10.10/10.11

Bug fixed:

1. Fixed the bug that when the Discovery Utility issues Controller_IP to EAPs which are in factory status, Controller cannot batch manage the EAPs.

2. Fixed the bug that sometimes the Discovery Utility cannot find all EAPs when running in MacOS.

Note:

1. This version of software can be used in both Windows and Mac operation system.

2. Double click the software or run the command “java –jar **.jar” to run the software on MacOS(**.jar is the name of this software).

3. To run this software, you need to install JRE 8.0 on your PC.

發佈日期: 2018-07-24 語言: 英語 檔案大小: 84.16 MB
作業系統: Mac OS X 10.7/10.8/10.9/10.10/10.11

New Feature/Enhancement:
1. Change name to "Omada Discovery Utility".
2. Update background picture during installation.
3. Limit the maximum length of controller hostname to 79.
 
Bug Fixed:
Fix the bug that searching in the search box will cause the software to hang.
 
Note:
Operating System: Mac OS X 10.7/10.8/10.9/10.10/10.11.

發佈日期: 2017-12-07 語言: 英語 檔案大小: 3.39 MB
作業系統: WinXP/Vista/7/8/8.1/10/Server2008/Server2012
T2700G-28TQ License Download
License Model: T2700G-28TQ-L1000

Find your product MAC and Serial Number.
License Key:
Product Serial Number:
Product MAC:
Checking code:

SubscriptionTP-Link takes your privacy seriously. For further details on TP-Link's privacy practices, see TP-Link's Privacy Policy.