Setup Video

  • How to manage TP-Link EAPs centrally via the Software Controller

    This video demonstrates how to manage TP-Link EAPs centrally via the Software Controller. The setup consists of three steps:
    • Install the Software
    • Configure Discovery Utility (If your EAPs and the Controller Host are on different subnets)
    • Configure Software Controller

    THIS VIDEO APPLIES TO:
    • All TP-Link EAP models (except EAP120 and EAP220)
    • Omada Software Controller
    • Mass EAPs (usually more than three)

    Weitere Informationen

  • How to set up a TP Link EAP via your mobile phone

    This video demonstrates how to set up a TP-Link EAP via your mobile phone. The setup consists of four steps:
    • Connect the EAP to the network
    • Download the Omada APP
    • Connect to the EAP's wireless network
    • Set up the EAP using the Omada APP

    THIS VIDEO APPLIES TO:
    • All TP-Link EAP models. (except EAP120 and EAP220)
    • A small number (1-3) of EAPs.

    Weitere Informationen

  • How to setup the OC200 via a web browser

    This video will demonstrate how to set up the OC200 via a web browser. The setup consists of six steps:
    • Connect the OC200 to your local network.
    • Get ready for setup.
    • Create a TP-Link ID.
    • Log into your TP-Link ID.
    • Add the OC200 to your TP-Link ID.
    • Follow the wizard to set up the OC200.

    THIS VIDEO APPLIES TO:
    • All TP-Link EAP models (except EAP120 and EAP220)
    • Omada Cloud Controller OC200
    • Mass EAPs (usually more than three)

    Weitere Informationen

  • How to setup the OC200 via your mobile phone

    This video will demonstrate how to set up the OC200 via your mobile phone. You need to use the Omada APP to complete the setup. The setup consists of six steps:
    • Connect the OC200 to your local network.
    • Get ready for setup.
    • Create a TP-Link ID.
    • Log into your TP-Link ID.
    • Add the OC200 to your TP-Link ID.
    • Follow the wizard to set up the OC200.
    THIS VIDEO APPLIES TO:
    • All TP-Link EAP models (except EAP120 and EAP220)
    • Omada Cloud Controller OC200
    • Mass EAPs (usually more than three)

    Weitere Informationen

  • How to manage TP-Link EAPs centrally from a remote place via a web browser

    You can manage TP-Link EAPs at any time from anywhere with the Cloud Access function of our Omada Controller Software. This video introduces both the application scenario and concrete steps you can follow. Don't hesitate to give it a try.
    THIS VIDEO APPLIES TO:
    • All TP-Link EAP models (except EAP120 and EAP220)
    • Omada Controller Software (version 3.0.2 or above)
    • Mass EAPs (usually more than three)

    Weitere Informationen

  • A Quick Overview of EAP Management Methods

    This video introduces how to choose the optimum method to manage TP-Link EAPs in your scenario.
    Here are 3 most common scenarios and their corresponding methods:
    • Manage 1 or 2 EAPs locally
    • Manage 3 or more EAPs locally
    • Manage 3 or more EAPs remotely
    When choosing the method, consider the following questions:
    1. Standalone Mode or Controller Mode?
    2. In Controller mode, what kind of controller will you use, an OC200 or a PC with Omada Software Controller?
    3. What kind of user interface will you use, a web browser or the Omada app?

    Weitere Informationen

  • How to Set up a TP-Link EAP via Web browser

    This video will demonstrate how to set up a TP-Link EAP via a web browser. The setup consists of three steps:
    1. Connect the EAP to the network
    2. Log into the EAP (via a wired/wireless connection)
    3. Change the default SSID
    This video is suitable for users with a small number (1-3) of EAPs .

    Weitere Informationen

Häufig gestellte Fragen

Firmware

Ein Firmware-Update kann für Sie neue Funktionen und Fehlerbehebungen und Performanceverbesserungen bereithalten.

Zum Firmware-Upgrade

HINWEIS: Um Fehler bei der Aktualisierung zu vermeiden, lesen Sie sich bitte folgende Hinweise durch, bevor Sie das Upgrade tätigen.

  • Bitte stellen Sie sicher, dass die Firmwareversion, die Sie zu installieren beabsichtigen, für Ihre Hardwareversion freigegeben ist. Eine nicht passende Firmware kann Ihr Gerät beschädigen und Ihren Anspruch auf Garantie erlöschen lassen. Normalerweise gilt V1.x=V1.
    Es wird NICHT empfohlen, eine nicht für Ihren Standort vorgesehene Firmware zu installieren. Klicken Sie hier, um Ihren Standort zu wählen und dann eine geeignete Firmware herunterzuladen (z.B. bestehen Unterschiede zwischen der EU- und der US-Version)
  • Trennen Sie während des Upgradevorgangs KEINESFALLS die Spannungsversorgung.
  • Aktualisieren Sie die Firmware NICHT über eine WLAN-Verbindung, außer Ihr Gerät verfügt über keinen Kabelanschluss.
  • Es wird empfohlen, während des Upgrades keine Internetanwendungen auszuführen bzw. einfach vor dem Upgrade die Internetverbindung des Gerätes zu trennen.
  • Verwenden Sie Entpack-Software wie WinZIP oder WinRAR, um die heruntergeladene Datei vor dem Upgrade zu entpacken.
EAP115-Wall(EU)_V1_1.5.0 Build 20191014
Datum der Veröffentlichung: 2020-01-14 Sprache: Englisch Dateigröße: 5.70 MB

Recommended Controller Software Version: Omada Controller v3.2.x or above

Bug Fixed:
1. Fixed the bug that the CPU usage of EAP may be high when EAPs are deployed densely.
2. Fixed the bug that EAP may disconnect from Omada Controller when EAPs are deployed densely. 

Notes:
1. For EAP115-Wall v1 only.
2. Your device's configuration won't be lost after upgrading.
3. This version of firmware is applied to Omada APP of version 2.1.X or above.

4. You cannot downgrade if you upgrade from 2018 or older firmware to this version directly.

 

Verwendung von Third-Party-Firmware auf TP-Link-Produkten

Die Original-Firmware einiger TP-Link-Produkte kann durch Third-Party-Firmware wie DD-WRT ersetzt werden. TP-Link ist weder verpflichtet, für derart modifizierte Geräte Support oder Garantie zu leisten noch für deren Stabilität oder Leistungsfähigkeit zu garantieren. TP-Link wird keinerlei durch Third-Party-Firmware verursachte Schäden ersetzen.

Open-Source-Code für Entwickler (GPL)

Die folgenden Informationen sind für Entwickler gedacht und für die meisten Nutzer von TP-Link-Produkten uninteressant.

TP-Link-Produkte enthalten teilweise von Dritten entwickelten Softwarecode, darunter Code, der unter die GNU General Public Licence (“GPL“), Version 1/Version 2/Version 3 oder die GNU Lesser General Public License ("LGPL") gestellt ist. Diese Software können Sie unter Beachtung der damit verbundenen Bedingungen benutzen.

Sie können die GPL-Lizenzbedingungen hier ansehen, herunterladen und drucken. Sie bekommen die GPL-Sourcecodes der in TP-Link-Produkten verwendeten Software per Direktdownload sowie weitere Information, unter Anderem eine Liste der TP-Link-Software, welche GPL-Softwarecode enthält, unter GPL Code Center.

Diese Programme werden OHNE JEGLICHE GEWÄHRLEISTUNG weitergegeben. Auch die HERSTELLERGARANTIE und die GEWÄHRLEISTUNG gelten für diese nicht. Für Details sei auf die GNU General Public License verwiesen.

Controller Software

The EAP Controller is used to manage multiple EAPs intensively.

Datum der Veröffentlichung: 2020-01-21 Sprache: Englisch Dateigröße: 120.53MB
Betriebssystem: Windows 7/8/10/Server

New Feature/Enhancement:

1. Expand the number of Omada Controller’s User Account to 500.  

2. Optimize the External Portal Server to support URL with parameters.

 

Notes:

1. To use Omada Controller 3.2.X new features, you need to upgrade your EAP's firmware to the corresponding version.

2. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

3. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.X or earlier version.

 

Datum der Veröffentlichung: 2020-01-21 Sprache: Englisch Dateigröße: 124.45MB
Betriebssystem: Windows 7/8/10/Server

New Feature/Enhancement:

1. Expand the number of Omada Controller’s User Account to 500.  

2. Optimize the External Portal Server to support URL with parameters.

 

Notes:

1. To use Omada Controller 3.2.X new features, you need to upgrade your EAP's firmware to the corresponding version.

2. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

3. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.X or earlier version.

Datum der Veröffentlichung: 2020-01-16 Sprache: Englisch Dateigröße: 123.35MB
Betriebssystem: Ubuntu 14.04/16.04/17.04/18.04, CentOS 6.x/7.x and Fedora 20 or above, Debian 9.8.

New Feature/Enhancement:

1. Change the mechanism that when adopting an EAP, the Controller will retain the IP configuration of EAP in Standalone mode.

2. Change the mechanism that multiple Omada Controllers can run on the same subnet.

3. Add the button of “Start Omada Controller after installation” and check it by default.

4. Extend the Max Associated Clients in Load Balance to 255.

5. Optimize the UI of Channel Utilization.

6. Optimize the authentication page of portal.

7. Optimize the UI of the portal that you cannot click Apply when you are uploading a photo.

8. Optimize the External Portal Server to support URL with parameters.

 

Bug Fixed:

1. Fixed the bug that the page of MAC filter may not display all groups when there are more than 5 groups.

2. Fixed the bug that after deleting a site, the Voucher code and Local user of this site still exist.

3. Fixed the bug that the site configuration will fail to restore when the imported site contains same Voucher code as the current Controller.

4. Fixed the bug that when mesh AP is powered off during upgrade, Controller may fail to upgrade other APs, with a prompt message “Other APs are upgrading”.

 

Notes:

1. To use new features on Omada Controller 3.2.x, you need to upgrade your EAP's firmware to the corresponding version.

2. The Omada Controller program needs to use the system's netstat command. If the Linux system does not have net-tools installed (which contain the netstat command), the program may not be able to run normally.

3. Support 64-bit Linux operating system including Ubuntu 14.04/16.04/17.04/18.04, CentOS 6.x/7.x and Fedora 20 or above, Debian 9.8.

4. Built-in JRE 1.8 Java environment.

5. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

6. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.8.

7. When upgrading from Controller 2.5.3 Linux to this version via install.sh, you need to uninstall old version of Controller first.

 

Datum der Veröffentlichung: 2020-01-16 Sprache: Englisch Dateigröße: 99.4MB
Betriebssystem: Ubuntu 14.04/16.04/17.04/18.04/Debian 9.8

New Feature/Enhancement:

1. Change the mechanism that when adopting an EAP, the Controller will retain the IP configuration of EAP in Standalone mode.

2. Change the mechanism that multiple Omada Controllers can run on the same subnet.

3. Add the button of “Start Omada Controller after installation” and check it by default.

4. Extend the Max Associated Clients in Load Balance to 255.

5. Optimize the UI of Channel Utilization.

6. Optimize the authentication page of portal.

7. Optimize the UI of the portal that you cannot click Apply when you are uploading a photo.

8. Optimize the External Portal Server to support URL with parameters.

 

Bug Fixed:

1. Fixed the bug that the page of MAC filter may not display all groups when there are more than 5 groups.

2. Fixed the bug that after deleting a site, the Voucher code and Local user of this site still exist.

3. Fixed the bug that the site configuration will fail to restore when the imported site contains same Voucher code as the current Controller.

4. Fixed the bug that when mesh AP is powered off during upgrade, Controller may fail to upgrade other APs, with a prompt message “Other APs are upgrading”.

 

Notes:

1. To use new features on Omada Controller 3.2.X, you need to upgrade your EAP's firmware to the corresponding version.

2. The Omada Controller program needs to use the system's netstat command. If the Linux system does not have net-tools installed (which contain the netstat command), the program may not be able to run normally.

3. Support 64-bit Linux operating system including Ubuntu 14.04/16.04/17.04/18.04/Debian 9.8

4. Built-in JRE 1.8 Java environment.

5. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

6. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.8.

Datum der Veröffentlichung: 2020-01-09 Sprache: Englisch Dateigröße: 120.53MB
Betriebssystem: Windows 7/8/10/Server

New Feature/Enhancement:

1. Change the mechanism that when adopting an EAP, the Controller will retain the IP configuration of EAP in Standalone mode.

2. Change the mechanism that multiple Omada Controllers can run on the same subnet.

3. Add the button of “Start Omada Controller after installation” and check it by default.

4. Extend the Max Associated Clients in Load Balance to 255.

5. Optimize the UI of Channel Utilization.

6. Optimize the authentication page of portal.

7. Optimize the UI of the portal that you cannot click Apply when you are uploading a photo.

 

Bug Fixed:

1. Fixed the bug that the page of MAC filter may not display all groups when there are more than 5 groups.

2. Fixed the bug that after deleting a site, the Voucher code and Local user of this site still exist.

3. Fixed the bug that the site configuration will fail to restore when the imported site contains same Voucher code as the current Controller.

4. Fixed the bug that when mesh AP is powered off during upgrade, Controller may fail to upgrade other APs, with a prompt message “Other APs are upgrading”.

 

Notes:

1. To use Omada Controller 3.2.X new features, you need to upgrade your EAP's firmware to the corresponding version.

2. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

3. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.X or earlier version.

Datum der Veröffentlichung: 2020-01-09 Sprache: Englisch Dateigröße: 124.44MB
Betriebssystem: Windows 7/8/10/Server

New Feature/Enhancement:

1. Change the mechanism that when adopting an EAP, the Controller will retain the IP configuration of EAP in Standalone mode.

2. Change the mechanism that multiple Omada Controllers can run on the same subnet.

3. Add the button of “Start Omada Controller after installation” and check it by default.

4. Extend the Max Associated Clients in Load Balance to 255.

5. Optimize the UI of Channel Utilization.

6. Optimize the authentication page of portal.

7. Optimize the UI of the portal that you cannot click Apply when you are uploading a photo.

 

Bug Fixed:

1. Fixed the bug that the page of MAC filter may not display all groups when there are more than 5 groups.

2. Fixed the bug that after deleting a site, the Voucher code and Local user of this site still exist.

3. Fixed the bug that the site configuration will fail to restore when the imported site contains same Voucher code as the current Controller.

4. Fixed the bug that when mesh AP is powered off during upgrade, Controller may fail to upgrade other APs, with a prompt message “Other APs are upgrading”.

 

Notes:

1. To use Omada Controller 3.2.X new features, you need to upgrade your EAP's firmware to the corresponding version.

2. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

3. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.X or earlier version.

T2700G-28TQ License Download
License Model: T2700G-28TQ-L1000

Find your product MAC and Serial Number.
License Key:
Product Serial Number:
Product MAC:
Checking code:

Subscription Für TP-Link ist Datenschutz sehr wichtig. Weitere Informationen zu unseren Datenschutzbedingungen finden Sie in der Datenschutzerklärung von TP-Link.