Download for EAP230-Wall V1

If you are planning to upgrade from the old controller(v3.2.10 or below) to this version, please read the Omada Controller Upgrade Guide in the installation package before upgrading the controller.

Supported device models and firmware:

EAP:

EAP110_V4 3.20.0 Build 20200525 Rel. 36899 and above

EAP115_V4 3.20.0 Build 20200525 Rel.36931 and above

EAP225_V3 2.20.0 Build 20200422 Rel. 70513 and above

EAP245_V3 2.20.0 Build 20200423 Rel. 36779 and above

EAP115-Wall_V1 1.20.0 Build 20200509 Rel. 63986 and above

EAP225-Wall_V2 1.20.0 Build 20200422 Rel. 70504 and above

EAP110-Outdoor_V3 3.20.0 Build 20200511 Rel. 33388 and above

EAP225-Outdoor_V1 1.20.0 Build 20200422 Rel. 70543 and above

EAP265 HD_V1, EAP230-Wall_V1, EAP235-Wall_V1, EAP660 HD_V1, EAP620 HD_V1

Switch:

TL_SG3428MP_V1, TL_SG3428_V1, TL-SG2210MP_V1, TL-SG2210P_V3.20, TL-SG2428P_V1, TL-SG2008P_V1, TL-SG2008_V3, TL-SG3428X_V1, TL_SG3428XMP_V1, TL-SG3210XHP-M2_V1, TL-SG3452P_V1, TL-SG3452_V1, TL-SG3428MP_V1, TL-SG3210_V3, TL-SG2218_V1, TL-SL2428P_V4.2

Gateway:

TL-R605_V1, TL-ER7206_V1

Bug Fixed:

1. Fixed the bug that the IPSec and L2TP over IPSec VPN cannot be set on the same WAN port at the same time.

2. Fixed the bug that the speedtest in the dashboard may display general error and internet Capacity and Gateway are still displayed as N/A.

3. Fixed the bug that we may not be able to re-adopt the Mesh AP if we failed to adopt it with the wrong password for the first time.

4. Fixed the bug that the wireless client will be displayed as a wired client (LAN) on the controller.

5. Fixed the bug that the controller's band steering range is inconsistent with the actual supported range of EAP, resulting in the configuration not taking effect.

6. Fixed the bug that the wired clients that have passed portal authentication may display 0 traffic data in the Authorized Clients list.

7. Fixed the bug that the wired clients that have passed portal authentication may have lower traffic statistics.

8. Fixed the bug that the Controller may show a general error if we forget an EAP and then delete an SSID.

9. Fixed the bug that the wired clients that have passed RADIUS portal authentication may have higher RADIUS accounting traffic statistics.

Notes:

1. Omada SDN Controller can configure and manage only certain devices with supported firmware. You need to make sure your device is compatible with Omada SDN Controller.

2. If you are using Omada Controller and plan to upgrade to this version, please follow the procedure of Omada Controller Upgrade Guide.

3. Once upgraded to this version of Omada Controller, you will be NOT able to downgrade to version 3.2.10 or below. 

4. This version of the controller is applied to Omada APP of version 3.0.X or above.

If you are planning to upgrade from the old controller(v3.2.10 or below) to this version, please read the Omada Controller Upgrade Guide in the installation package before upgrading the controller.

Supported device models and firmware:

EAP:

EAP110_V4 3.20.0 Build 20200525 Rel. 36899 and above

EAP115_V4 3.20.0 Build 20200525 Rel.36931 and above

EAP225_V3 2.20.0 Build 20200422 Rel. 70513 and above

EAP245_V3 2.20.0 Build 20200423 Rel. 36779 and above

EAP115-Wall_V1 1.20.0 Build 20200509 Rel. 63986 and above

EAP225-Wall_V2 1.20.0 Build 20200422 Rel. 70504 and above

EAP110-Outdoor_V3 3.20.0 Build 20200511 Rel. 33388 and above

EAP225-Outdoor_V1 1.20.0 Build 20200422 Rel. 70543 and above

EAP265 HD_V1, EAP230-Wall_V1, EAP235-Wall_V1, EAP660 HD_V1, EAP620 HD_V1

Switch:

TL_SG3428MP_V1, TL_SG3428_V1, TL-SG2210MP_V1, TL-SG2210P_V3.20, TL-SG2428P_V1, TL-SG2008P_V1, TL-SG2008_V3, TL-SG3428X_V1, TL_SG3428XMP_V1, TL-SG3210XHP-M2_V1, TL-SG3452P_V1, TL-SG3452_V1, TL-SG3428MP_V1, TL-SG3210_V3, TL-SG2218_V1, TL-SL2428P_V4.2

Gateway:

TL-R605_V1, TL-ER7206_V1

Bug Fixed:

1. Fixed the bug that the IPSec and L2TP over IPSec VPN cannot be set on the same WAN port at the same time.

2. Fixed the bug that the speedtest in the dashboard may display general error and internet Capacity and Gateway are still displayed as N/A.

3. Fixed the bug that we may not be able to re-adopt the Mesh AP if we failed to adopt it with the wrong password for the first time.

4. Fixed the bug that the wireless client will be displayed as a wired client (LAN) on the controller.

5. Fixed the bug that the controller's band steering range is inconsistent with the actual supported range of EAP, resulting in the configuration not taking effect.

6. Fixed the bug that the wired clients that have passed portal authentication may display 0 traffic data in the Authorized Clients list.

7. Fixed the bug that the wired clients that have passed portal authentication may have lower traffic statistics.

8. Fixed the bug that the Controller may show a general error if we forget an EAP and then delete an SSID.

9. Fixed the bug that the wired clients that have passed RADIUS portal authentication may have higher RADIUS accounting traffic statistics.

Notes:

1. Omada SDN Controller can configure and manage only certain devices with supported firmware. You need to make sure your device is compatible with Omada SDN Controller.

2. If you are using Omada Controller and plan to upgrade to this version, please follow the procedure of Omada Controller Upgrade Guide.

3. Once upgraded to this version of Omada Controller, you will be NOT able to downgrade to an earlier version. 

4. This version of the controller is applied to Omada APP of version 3.0.X or above.

5. Controller needs Java 8 and MongoDB 3.0-3.6 for running. And there are no built-in JRE and MongoDB, so you need to install them by yourself.

6. Support 64-bit Linux operating system including Ubuntu 14.04/16.04/17.04/18.04, CentOS 6.x/7.x and Fedora 20 or above, Debian.

If you are planning to upgrade from the old controller(v3.2.10 or below) to this version, please read the Omada Controller Upgrade Guide in the installation package before upgrading the controller.

Supported device models and firmware:

EAP:

EAP110_V4 3.20.0 Build 20200525 Rel. 36899 and above

EAP115_V4 3.20.0 Build 20200525 Rel.36931 and above

EAP225_V3 2.20.0 Build 20200422 Rel. 70513 and above

EAP245_V3 2.20.0 Build 20200423 Rel. 36779 and above

EAP115-Wall_V1 1.20.0 Build 20200509 Rel. 63986 and above

EAP225-Wall_V2 1.20.0 Build 20200422 Rel. 70504 and above

EAP110-Outdoor_V3 3.20.0 Build 20200511 Rel. 33388 and above

EAP225-Outdoor_V1 1.20.0 Build 20200422 Rel. 70543 and above

EAP265 HD_V1, EAP230-Wall_V1, EAP235-Wall_V1, EAP660 HD_V1, EAP620 HD_V1

Switch:

TL_SG3428MP_V1, TL_SG3428_V1, TL-SG2210MP_V1, TL-SG2210P_V3.20, TL-SG2428P_V1, TL-SG2008P_V1, TL-SG2008_V3, TL-SG3428X_V1, TL_SG3428XMP_V1, TL-SG3210XHP-M2_V1, TL-SG3452P_V1, TL-SG3452_V1, TL-SG3428MP_V1, TL-SG3210_V3, TL-SG2218_V1, TL-SL2428P_V4.2

Gateway:

TL-R605_V1, TL-ER7206_V1

Bug Fixed:

1. Fixed the bug that the IPSec and L2TP over IPSec VPN cannot be set on the same WAN port at the same time.

2. Fixed the bug that the speedtest in the dashboard may display general error and internet Capacity and Gateway are still displayed as N/A.

3. Fixed the bug that we may not be able to re-adopt the Mesh AP if we failed to adopt it with the wrong password for the first time.

4. Fixed the bug that the wireless client will be displayed as a wired client (LAN) on the controller.

5. Fixed the bug that the controller's band steering range is inconsistent with the actual supported range of EAP, resulting in the configuration not taking effect.

6. Fixed the bug that the wired clients that have passed portal authentication may display 0 traffic data in the Authorized Clients list.

7. Fixed the bug that the wired clients that have passed portal authentication may have lower traffic statistics.

8. Fixed the bug that the Controller may show a general error if we forget an EAP and then delete an SSID.

9. Fixed the bug that the wired clients that have passed RADIUS portal authentication may have higher RADIUS accounting traffic statistics.

Notes:

1. Omada SDN Controller can configure and manage only certain devices with supported firmware. You need to make sure your device is compatible with Omada SDN Controller.

2. If you are using Omada Controller and plan to upgrade to this version, please follow the procedure of Omada Controller Upgrade Guide.

3. Once upgraded to this version of Omada Controller, you will be NOT able to downgrade to version 3.2.10 or below. 

4. This version of the controller is applied to Omada APP of version 3.0.X or above.

5. Support 64-bit Linux operating system including Ubuntu 14.04/16.04/17.04/18.04/Debian.

6. You may need to save the backup file and uninstall the old Omada Controller before installing this software.

Bundled Firmware:
EAP110_V1, EAP110_V2 EAP110_V4
EAP115_V1, EAP115_V2 EAP115_V4
EAP225_V1, EAP225_V2 EAP225_V3
EAP225-Outdoor_V1
EAP110-Outdoor_V1 EAP110-Outdoor_V3
EAP245_V1 EAP245_V3
EAP115-Wall_V1 (EAP115-Wall is suitable for EU version only)
EAP225-Wall_V2 
EAP320_V1 EAP320_V2
EAP330_V1 EAP330_V2

Bug Fixed:
1. Fixed the XSS attack vulnerability

Notes:
1. To use Omada Controller 3.2.X new features, you need to upgrade your EAP's firmware to the corresponding version.
2. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.
 

Bundled Firmware:
EAP110_V1, EAP110_V2 EAP110_V4
EAP115_V1, EAP115_V2 EAP115_V4
EAP225_V1, EAP225_V2 EAP225_V3
EAP225-Outdoor_V1
EAP110-Outdoor_V1 EAP110-Outdoor_V3
EAP245_V1 EAP245_V3
EAP115-Wall_V1 (EAP115-Wall is suitable for EU version only)
EAP225-Wall_V2 
EAP320_V1 EAP320_V2
EAP330_V1 EAP330_V2

Bug Fixed:
1. Fixed the XSS attack vulnerability

Notes:
1. To use Omada Controller 3.2.X new features, you need to upgrade your EAP's firmware to the corresponding version.
2. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

Bundled Firmware:
EAP110_V1, EAP110_V2 EAP110_V4
EAP115_V1, EAP115_V2 EAP115_V4
EAP225_V1, EAP225_V2 EAP225_V3
EAP225-Outdoor_V1
EAP110-Outdoor_V1 EAP110-Outdoor_V3
EAP245_V1 EAP245_V3
EAP115-Wall_V1 (EAP115-Wall is suitable for EU version only)
EAP225-Wall_V2 
EAP320_V1 EAP320_V2
EAP330_V1 EAP330_V2

Bug Fixed:
1. Fixed the XSS attack vulnerability

Notes:
1. To use Omada Controller 3.2.X new features, you need to upgrade your EAP's firmware to the corresponding version.
2. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.
 

Bundled Firmware:
EAP110_V1, EAP110_V2 EAP110_V4
EAP115_V1, EAP115_V2 EAP115_V4
EAP225_V1, EAP225_V2 EAP225_V3
EAP225-Outdoor_V1
EAP110-Outdoor_V1 EAP110-Outdoor_V3
EAP245_V1 EAP245_V3
EAP115-Wall_V1 (EAP115-Wall is suitable for EU version only)
EAP225-Wall_V2 
EAP320_V1 EAP320_V2
EAP330_V1 EAP330_V2

Bug Fixed:
1. Fixed the XSS attack vulnerability

Notes:
1. To use Omada Controller 3.2.X new features, you need to upgrade your EAP's firmware to the corresponding version.
2. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

If you are planning to upgrade from the old controller(v3.2.10 or below) to this version, please read the Omada Controller Upgrade Guide in the installation package before upgrading the controller.

Supported device models and firmware:

EAP:

EAP110_V4 3.20.0 Build 20200525 Rel. 36899 and above

EAP115_V4 3.20.0 Build 20200525 Rel.36931 and above

EAP225_V3 2.20.0 Build 20200422 Rel. 70513 and above

EAP245_V3 2.20.0 Build 20200423 Rel. 36779 and above

EAP115-Wall_V1 1.20.0 Build 20200509 Rel. 63986 and above

EAP225-Wall_V2 1.20.0 Build 20200422 Rel. 70504 and above

EAP110-Outdoor_V3 3.20.0 Build 20200511 Rel. 33388 and above

EAP225-Outdoor_V1 1.20.0 Build 20200422 Rel. 70543 and above

EAP265 HD_V1, EAP230-Wall_V1, EAP235-Wall_V1, EAP660 HD_V1, EAP620 HD_V1

Switch:

TL_SG3428MP_V1, TL_SG3428_V1, TL-SG2210MP_V1, TL-SG2210P_V3.20, TL-SG2428P_V1, TL-SG2008P_V1, TL-SG2008_V3, TL-SG3428X_V1, TL_SG3428XMP_V1, TL-SG3210XHP-M2_V1

Gateway:

TL-R605_V1, TL-ER7206_V1

New Feature/Enhancement:

1. Support to manage TL-SL2428P(UN) 4.20.

2. Optimize the protocol for the device reporting information of rate/duplex capability.

3. Optimize the password retrieval mechanism. If multiple local accounts are bound to one mailbox, you can choose which account to reset the password.

4. Add the batch cancelling of devices migration in the migration function.

5. Vulnerability optimization

Bug Fixed:

1. Fixed the bug that the device will move to the upper left corner when you visit again if the device location is locked in the MAP.

2. Fixed the bug that uplink signal strength of Mesh EAP is not displayed accurately on the devices private configuration page.

3. Fixed the bug that the user without device permission may display that it still has permission in the account settings.

4. Fixed the bug that the function of Log Server/Alert Email may not take effect after restoring the backup file of Controller.

5. Fixed the bug that you may unsuccessfully import the local user account in the Hotspot Manager.

6. Fixed the bug that the “Last Seen” time in the private configuration page of the switch is the last uptime (not the last disconnected time) after the switch disconnects from Omada Controller.

7. Fixed the bug that the expiration time of Facebook authentication in “->authorized clients” is inconsistent with the actual expiration time.

8. Fixed the bug that the Controller may generate lots of roaming logs if clients leave from one EAP to another EAP implicitly since clients still send auth frame to the previous EAP.

Notes:

1. Omada SDN Controller can configure and manage only certain devices with supported firmware. You need to make sure your device is compatible with Omada SDN Controller.

2. If you are using Omada Controller and plan to upgrade to this version, please follow the procedure of Omada Controller Upgrade Guide.

3. Once upgraded to this version of Omada Controller, you will be NOT able to downgrade to an earlier version. 

4. This version of the controller is applied to Omada APP of version 3.0.X or above.

5. Controller needs Java 8 and MongoDB 3.0-3.6 for running. And there are no built-in JRE and MongoDB, so you need to install them by yourself.

6. Support 64-bit Linux operating system including Ubuntu 14.04/16.04/17.04/18.04, CentOS 6.x/7.x and Fedora 20 or above, Debian.

If you are planning to upgrade from the old controller(v3.2.10 or below) to this version, please read the Omada Controller Upgrade Guide in the installation package before upgrading the controller.

Supported device models and firmware:

EAP:

EAP110_V4 3.20.0 Build 20200525 Rel. 36899 and above

EAP115_V4 3.20.0 Build 20200525 Rel.36931 and above

EAP225_V3 2.20.0 Build 20200422 Rel. 70513 and above

EAP245_V3 2.20.0 Build 20200423 Rel. 36779 and above

EAP115-Wall_V1 1.20.0 Build 20200509 Rel. 63986 and above

EAP225-Wall_V2 1.20.0 Build 20200422 Rel. 70504 and above

EAP110-Outdoor_V3 3.20.0 Build 20200511 Rel. 33388 and above

EAP225-Outdoor_V1 1.20.0 Build 20200422 Rel. 70543 and above

EAP265 HD_V1, EAP230-Wall_V1, EAP235-Wall_V1, EAP660 HD_V1, EAP620 HD_V1

Switch:

TL_SG3428MP_V1, TL_SG3428_V1, TL-SG2210MP_V1, TL-SG2210P_V3.20, TL-SG2428P_V1, TL-SG2008P_V1, TL-SG2008_V3, TL-SG3428X_V1, TL_SG3428XMP_V1, TL-SG3210XHP-M2_V1

Gateway:

TL-R605_V1, TL-ER7206_V1

New Feature/Enhancement:

1. Support to manage TL-SL2428P(UN) 4.20.

2. Optimize the protocol for the device reporting information of rate/duplex capability.

3. Optimize the password retrieval mechanism. If multiple local accounts are bound to one mailbox, you can choose which account to reset the password.

4. Add the batch cancelling of devices migration in the migration function.

5. Vulnerability optimization

Bug Fixed:

1. Fixed the bug that the device will move to the upper left corner when you visit again if the device location is locked in the MAP.

2. Fixed the bug that uplink signal strength of Mesh EAP is not displayed accurately on the devices private configuration page.

3. Fixed the bug that the user without device permission may display that it still has permission in the account settings.

4. Fixed the bug that the function of Log Server/Alert Email may not take effect after restoring the backup file of Controller.

5. Fixed the bug that you may unsuccessfully import the local user account in the Hotspot Manager.

6. Fixed the bug that the “Last Seen” time in the private configuration page of the switch is the last uptime (not the last disconnected time) after the switch disconnects from Omada Controller.

7. Fixed the bug that the expiration time of Facebook authentication in “->authorized clients” is inconsistent with the actual expiration time.

8. Fixed the bug that the Controller may generate lots of roaming logs if clients leave from one EAP to another EAP implicitly since clients still send auth frame to the previous EAP.

Notes:

1. Omada SDN Controller can configure and manage only certain devices with supported firmware. You need to make sure your device is compatible with Omada SDN Controller.

2. If you are using Omada Controller and plan to upgrade to this version, please follow the procedure of Omada Controller Upgrade Guide.

3. Once upgraded to this version of Omada Controller, you will be NOT able to downgrade to version 3.2.10 or below. 

4. This version of the controller is applied to Omada APP of version 3.0.X or above.

5. Support 64-bit Linux operating system including Ubuntu 14.04/16.04/17.04/18.04/Debian.

6. You may need to save the backup file and uninstall the old Omada Controller before installing this software.

If you are planning to upgrade from the old controller(v3.2.10 or below) to this version, please read the Omada Controller Upgrade Guide in the installation package before upgrading the controller.

Supported device models and firmware:
EAP:
EAP110_V4 3.20.0 Build 20200525 Rel. 36899 and above
EAP115_V4 3.20.0 Build 20200525 Rel.36931 and above
EAP225_V3 2.20.0 Build 20200422 Rel. 70513 and above
EAP245_V3 2.20.0 Build 20200423 Rel. 36779 and above
EAP115-Wall_V1 1.20.0 Build 20200509 Rel. 63986 and above
EAP225-Wall_V2 1.20.0 Build 20200422 Rel. 70504 and above
EAP110-Outdoor_V3 3.20.0 Build 20200511 Rel. 33388 and above
EAP225-Outdoor_V1 1.20.0 Build 20200422 Rel. 70543 and above
EAP265 HD_V1, EAP230-Wall_V1, EAP235-Wall_V1, EAP660 HD_V1, EAP620 HD_V1

Switch:
TL_SG3428MP_V1, TL_SG3428_V1, TL-SG2210MP_V1, TL-SG2210P_V3.20, TL-SG2428P_V1, TL-SG2008P_V1, TL-SG2008_V3, TL-SG3428X_V1, TL_SG3428XMP_V1, TL-SG3210XHP-M2_V1,TL-SL2428P(UN) 4.2

Gateway:
TL-R605_V1, TL-ER7206_V1

New Feature/Enhancement:
1. Support to manage TL-SL2428P(UN) 4.20.
2. Optimize the protocol for the device reporting information of rate/duplex capability.
3. Optimize the password retrieval mechanism. If multiple local accounts are bound to one mailbox, you can choose which account to reset the password.
4. Add the batch cancelling of devices migration in the migration function.
5. Vulnerability optimization

Bug Fixed:
1. Fixed the bug that the device will move to the upper left corner when you visit again if the device location is locked in the MAP.
2. Fixed the bug that uplink signal strength of Mesh EAP is not displayed accurately on the devices private configuration page.
3. Fixed the bug that the user without device permission may display that it still has permission in the account settings.
4. Fixed the bug that the function of Log Server/Alert Email may not take effect after restoring the backup file of Controller.
5. Fixed the bug that you may unsuccessfully import the local user account in the Hotspot Manager.
6. Fixed the bug that the “Last Seen” time in the private configuration page of the switch is the last uptime (not the last disconnected time) after the switch disconnects from Omada Controller.
7. Fixed the bug that the expiration time of Facebook authentication in “hotspot->authorized clients” is inconsistent with the actual expiration time.
8. Fixed the bug that the Controller may generate lots of roaming logs if clients leave from one EAP to another EAP implicitly since clients still send auth frame to the previous EAP. 

If you are planning to upgrade from the old controller(v3.2.10 or below) to this version, please read the Omada Controller Upgrade Guide before upgrading the controller.

Supported device models and firmware:

EAP:

EAP110_V4 3.20.0 Build 20200525 Rel. 36899 and above

EAP115_V4 3.20.0 Build 20200525 Rel.36931 and above

EAP225_V3 2.20.0 Build 20200422 Rel. 70513 and above

EAP245_V3 2.20.0 Build 20200423 Rel. 36779 and above

EAP115-Wall_V1 1.20.0 Build 20200509 Rel. 63986 and above

EAP225-Wall_V2 1.20.0 Build 20200422 Rel. 70504 and above

EAP110-Outdoor_V3 3.20.0 Build 20200511 Rel. 33388 and above

EAP225-Outdoor_V1 1.20.0 Build 20200422 Rel. 70543 and above

EAP265 HD_V1, EAP230-Wall_V1, EAP235-Wall_V1, EAP660 HD_V1, EAP620 HD_V1

Switch:

TL_SG3428MP_V1, TL_SG3428_V1, TL-SG2210MP_V1, TL-SG2210P_V3.20, TL-SG2428P_V1, TL-SG2008P_V1, TL-SG2008_V3, TL-SG3428X_V1, TL_SG3428XMP_V1, TL-SG3210XHP-M2_V1

Gateway:

TL-R605_V1, TL-ER7206_V1

New Feature/Enhancement:

1. Support to import the SSL certificate of PFX format. 

2. Support to create of up to 1000 sites.

3. Support arbitrary adjustment of logo display and closing logo.

4. Support to paste the IP address for everywhere there is IP setting.

5. Support to restore the site privilege setting for cloud users when backup and restore for the same controller.

6. Support to print all unused voucher codes. 

7. Support to delete the archived alert log and event log.

8. Support to export device list, client list, etc. in Export Data function. 

9. Support to drag and drop card adjust the dashboard display.

10. Add the Hostname/IP setting which will be used for the controller URL in the notification email.

11. Add Past Connection page in the Insight menu.

12. Improve the MAP topology display.  

Bug Fixed:

1. Fixed the bug that the Limited Online Users voucher code still can be used after expired.

2. Fixed the bug that cannot use the website subpath in The Promotional URL settings of portal function.

3. Fixed the bug that cannot import the picture in MAP and Portal settings if access controller with cloud access.

4. Fixed the bug that the cutout logo will show a black background.

5. Fixed the bug that auto backup and schedule function cannot work if the time zone uses summertime.

Notes:

1. Omada SDN Controller can configure and manage only certain devices with supported firmware. You need to make sure your device is compatible with Omada SDN Controller.

2. If you are using Omada Controller and plan to upgrade to this version, please follow the procedure of Omada Controller Upgrade Guide.

3. Once upgraded to this version of Omada Controller, you will be NOT able to downgrade to an earlier version. 

4. This version of the controller is applied to Omada APP of version 3.0.X or above.

5. Controller needs Java 8 and MongoDB 3.0-3.6 for running. And there are no built-in JRE and MongoDB, so you need to install them by yourself.

If you are planning to upgrade from the old controller(v3.2.10 or below) to this version, please read the Omada Controller Upgrade Guide in the installation package before upgrading the controller.

Supported device models and firmware:

EAP:

EAP110_V4 3.20.0 Build 20200525 Rel. 36899 and above

EAP115_V4 3.20.0 Build 20200525 Rel.36931 and above

EAP225_V3 2.20.0 Build 20200422 Rel. 70513 and above

EAP245_V3 2.20.0 Build 20200423 Rel. 36779 and above

EAP115-Wall_V1 1.20.0 Build 20200509 Rel. 63986 and above

EAP225-Wall_V2 1.20.0 Build 20200422 Rel. 70504 and above

EAP110-Outdoor_V3 3.20.0 Build 20200511 Rel. 33388 and above

EAP225-Outdoor_V1 1.20.0 Build 20200422 Rel. 70543 and above

EAP265 HD_V1, EAP230-Wall_V1, EAP235-Wall_V1, EAP660 HD_V1, EAP620 HD_V1

Switch:

TL_SG3428MP_V1, TL_SG3428_V1, TL-SG2210MP_V1, TL-SG2210P_V3.20, TL-SG2428P_V1, TL-SG2008P_V1, TL-SG2008_V3, TL-SG3428X_V1, TL_SG3428XMP_V1, TL-SG3210XHP-M2_V1

Gateway:

TL-R605_V1, TL-ER7206_V1

New Feature/Enhancement:

1. Support to import the SSL certificate of PFX format. 

2. Support to create of up to 1000 sites.

3. Support arbitrary adjustment of logo display and closing logo.

4. Support to paste the IP address for everywhere there is IP setting.

5. Support to restore the site privilege setting for cloud users when backup and restore for the same controller.

6. Support to print all unused voucher codes. 

7. Support to delete the archived alert log and event log.

8. Support to export device list, client list, etc. in Export Data function. 

9. Support to drag and drop card adjust the dashboard display.

10. Add the Hostname/IP setting which will be used for the controller URL in the notification email.

11. Add Past Connection page in the Insight menu.

12. Improve the MAP topology display.  

Bug Fixed:

1. Fixed the bug that the Limited Online Users voucher code still can be used after expired.

2. Fixed the bug that cannot use the website subpath in The Promotional URL settings of portal function.

3. Fixed the bug that cannot import the picture in MAP and Portal settings if access controller with cloud access.

4. Fixed the bug that the cutout logo will show a black background.

5. Fixed the bug that auto backup and schedule function cannot work if the time zone uses summertime.

Notes:

1. Omada SDN Controller can configure and manage only certain devices with supported firmware. You need to make sure your device is compatible with Omada SDN Controller.

2. If you are using Omada Controller and plan to upgrade to this version, please follow the procedure of Omada Controller Upgrade Guide.

3. Once upgraded to this version of Omada Controller, you will be NOT able to downgrade to version 3.2.10 or below. 

4. This version of the controller is applied to Omada APP of version 3.0.X or above.

If you are planning to upgrade from the old controller to this version, please read the Omada Controller Upgrade Guide in the installation package before upgrading the controller.

Supported device models and firmware:

EAP110_V4 3.20.0 Build 20200525 Rel. 36899 and above

EAP115_V4 3.20.0 Build 20200525 Rel.36931 and above

EAP225_V3 2.20.0 Build 20200422 Rel. 70513 and above

EAP245_V3 2.20.0 Build 20200423 Rel. 36779 and above

EAP115-Wall_V1 1.20.0 Build 20200509 Rel. 63986 and above

EAP225-Wall_V2 1.20.0 Build 20200422 Rel. 70504 and above

EAP110-Outdoor_V3 3.20.0 Build 20200511 Rel. 33388 and above

EAP225-Outdoor_V1 1.20.0 Build 20200422 Rel. 70543 and above

EAP265 HD_V1

EAP230-Wall_V1

EAP235-Wall_V1

New Feature/Enhancement:

1. Omada SDN software controller provides a unified approach to configuring enterprise networks comprised of routers, switches, and wireless access points.

2. Brand new UI and style to provide high-efficiency, rapid and comprehensive network settings and maintenance function.

3. Add brand new Dashboard interface to monitor network operation in real time.

4. Add Statistics interface to monitor devices and show the statistics of network operation data.

5. Add Topology interface to generate the network topology automatically.

6. Add Insight interface to view the detailed network history data.

7. Add Logs interface that supports 100+ types of logs and custom warning level of logs.

8. Support to configure for gateway, including Internet, LAN Network, ACL, URL Filtering, VPN, Routing, NAT, Session Limit, Bandwidth Control, Portal and so on.

9. Support to configure for switch, including 802.1Q VLAN, ACL, 802.1x, IGMP Snooping, STP and so on.

10. Add Reboot Schedule and PoE Schedule and support to set different schedules for each device.

Notes:

1. Omada SDN Controller can configure and manage only the certain devices with supported firmware. You need to make sure your device is compatible with Omada SDN Controller.

2. If you are using Omada Controller and plan to upgrade to this version, please follow the procedure of Omada Controller Upgrade Guide.

3. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

4. This version of controller is applied to Omada APP of version 3.0.X or above.

5. Controller needs Java 8 and MongoDB 3.0.15-3.6.18 for running. And there are no built-in JRE and MongoDB, so you need to install them by yourself.

If you are planning to upgrade from the old controller to this version, please read the Omada Controller Upgrade Guide in the installation package before upgrading the controller.

Supported device models and firmware:

EAP110_V4 3.20.0 Build 20200525 Rel. 36899 and above

EAP115_V4 3.20.0 Build 20200525 Rel.36931 and above

EAP225_V3 2.20.0 Build 20200422 Rel. 70513 and above

EAP245_V3 2.20.0 Build 20200423 Rel. 36779 and above

EAP115-Wall_V1 1.20.0 Build 20200509 Rel. 63986 and above

EAP225-Wall_V2 1.20.0 Build 20200422 Rel. 70504 and above

EAP110-Outdoor_V3 3.20.0 Build 20200511 Rel. 33388 and above

EAP225-Outdoor_V1 1.20.0 Build 20200422 Rel. 70543 and above

EAP265 HD_V1

EAP230-Wall_V1

EAP235-Wall_V1

New Feature/Enhancement:

1. Omada SDN software controller provides a unified approach to configuring enterprise networks comprised of routers, switches, and wireless access points.

2. Brand new UI and style to provide high-efficiency, rapid and comprehensive network settings and maintenance function.

3. Add brand new Dashboard interface to monitor network operation in real time.

4. Add Statistics interface to monitor devices and show the statistics of network operation data.

5. Add Topology interface to generate the network topology automatically.

6. Add Insight interface to view the detailed network history data.

7. Add Logs interface that supports 100+ types of logs and custom warning level of logs.

8. Support to configure for gateway, including Internet, LAN Network, ACL, URL Filtering, VPN, Routing, NAT, Session Limit, Bandwidth Control, Portal and so on.

9. Support to configure for switch, including 802.1Q VLAN, ACL, 802.1x, IGMP Snooping, STP and so on.

10. Add Reboot Schedule and PoE Schedule and support to set different schedules for each device.

Notes:

1. Omada SDN Controller can configure and manage only the certain devices with supported firmware. You need to make sure your device is compatible with Omada SDN Controller.

2. If you are using Omada Controller and plan to upgrade to this version, please follow the procedure of Omada Controller Upgrade Guide.

3. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

4. This version of controller is applied to Omada APP of version 3.0.X or above.

5. Controller needs Java 8 and MongoDB 3.0.15-3.6.18 for running. And there are no built-in JRE and MongoDB, so you need to install them by yourself.

If you are planning to upgrade from the old controller to this version, please read the Omada Controller Upgrade Guide in the installation package before upgrading the controller.

Supported device models and firmware:

EAP110_V4 3.20.0 Build 20200525 Rel. 36899 and above

EAP115_V4 3.20.0 Build 20200525 Rel.36931 and above

EAP225_V3 2.20.0 Build 20200422 Rel. 70513 and above

EAP245_V3 2.20.0 Build 20200423 Rel. 36779 and above

EAP115-Wall_V1 1.20.0 Build 20200509 Rel. 63986 and above

EAP225-Wall_V2 1.20.0 Build 20200422 Rel. 70504 and above

EAP110-Outdoor_V3 3.20.0 Build 20200511 Rel. 33388 and above

EAP225-Outdoor_V1 1.20.0 Build 20200422 Rel. 70543 and above

EAP265 HD_V1

EAP230-Wall_V1

EAP235-Wall_V1

New Feature/Enhancement:

1. Omada SDN software controller provides a unified approach to configuring enterprise networks comprised of routers, switches, and wireless access points.

2. Brand new UI and style to provide high-efficiency, rapid and comprehensive network settings and maintenance function.

3. Add brand new Dashboard interface to monitor network operation in real time.

4. Add Statistics interface to monitor devices and show the statistics of network operation data.

5. Add Topology interface to generate the network topology automatically.

6. Add Insight interface to view the detailed network history data.

7. Add Logs interface that supports 100+ types of logs and custom warning level of logs.

8. Support to configure for gateway, including Internet, LAN Network, ACL, URL Filtering, VPN, Routing, NAT, Session Limit, Bandwidth Control, Portal and so on.

9. Support to configure for switch, including 802.1Q VLAN, ACL, 802.1x, IGMP Snooping, STP and so on.

10. Add Reboot Schedule and PoE Schedule and support to set different schedules for each device.

Notes:

1. Omada SDN Controller can configure and manage only the certain devices with supported firmware. You need to make sure your device is compatible with Omada SDN Controller.

2. If you are using Omada Controller and plan to upgrade to this version, please follow the procedure of Omada Controller Upgrade Guide.

3. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

4. This version of controller is applied to Omada APP of version 3.0.X or above.

New Feature/Enhancement:

1. Added the feature that the system logs can be exported.

2. Changed the priority that non-administrator role cannot change the history data retention settings.

3. Optimized the UI of Statistics in Omada Controller.

Bug Fixed:

1. Fixed the bug that the External Web Portal cannot authenticate successfully if the SSID of this portal has special characters.

2. Fixed the bug that the Cloud Access cannot be displayed normally in the low version of Firefox.

3. Fixed the bug that Omada Controller allow any user to read the files of controller.

4. Fixed the bug that controller will report an error when Top Usage data is empty.

Notes:

1. To use Omada Controller 3.2.X new features, you need to upgrade your EAP's firmware to the corresponding version.

2. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

3. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.X or earlier version.

New Feature/Enhancement:

1. Added the feature that the system logs can be exported.

2. Changed the priority that non-administrator role cannot change the history data retention settings.

3. Optimized the UI of Statistics in Omada Controller.

Bug Fixed:

1. Fixed the bug that the External Web Portal cannot authenticate successfully if the SSID of this portal has special characters.

2. Fixed the bug that the Cloud Access cannot be displayed normally in the low version of Firefox.

3. Fixed the bug that Omada Controller allow any user to read the files of controller.

4. Fixed the bug that controller will report an error when Top Usage data is empty.

Notes:

1. To use Omada Controller 3.2.X new features, you need to upgrade your EAP's firmware to the corresponding version.

2. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

3. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.X or earlier version.

Bug Fixed:

1. Fixed the bug that Omada Controller allow any user to read the files of controller.

2. Fixed the bug that controller will report an error when Top Usage data is empty. 

Notes:

1. To use new features on Omada Controller 3.2.X, you need to upgrade your EAP's firmware to the corresponding version.

2. The Omada Controller program needs to use the system's netstat command. If the Linux system does not have net-tools installed (which contain the netstat command), the program may not be able to run normally.

3. Support 64-bit Linux operating system including Ubuntu 14.04/16.04/17.04/18.04/Debian 9.8

4. Built-in JRE 1.8 Java environment.

5. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

6. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.8.

Bug Fixed:

1. Fixed the bug that Omada Controller allow any user to read the files of controller.

2. Fixed the bug that controller will report an error when Top Usage data is empty. 

Notes:

1. To use new features on Omada Controller 3.2.x, you need to upgrade your EAP's firmware to the corresponding version.

2. The Omada Controller program needs to use the system's netstat command. If the Linux system does not have net-tools installed (which contain the netstat command), the program may not be able to run normally.

3. Support 64-bit Linux operating system including Ubuntu 14.04/16.04/17.04/18.04, CentOS 6.x/7.x and Fedora 20 or above, Debian 9.8.

4. Built-in JRE 1.8 Java environment.

5. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

6. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.8.

7. When upgrading from Controller 2.5.3 Linux to this version via install.sh, you need to uninstall old version of Controller first.

New Feature/Enhancement:

1. Add the feature that the system logs can be exported.

2. Change the priority that non-administrator role cannot change the history data retention settings.

3. Optimize the UI of Statistics in Omada Controller.

Bug Fixed:

1. Fix the bug that the External Web Portal cannot authenticate successfully if the SSID of this portal has special characters.

2. Fix the bug that the Cloud Access cannot be displayed normally in the low version of Firefox.

Notes:

1. To use new features on Omada Controller 3.2.X, you need to upgrade your EAP's firmware to the corresponding version.

2. The Omada Controller program needs to use the system's netstat command. If the Linux system does not have net-tools installed (which contain the netstat command), the program may not be able to run normally.

3. Support 64-bit Linux operating system including Ubuntu 14.04/16.04/17.04/18.04/Debian 9.8

4. Built-in JRE 1.8 Java environment.

5. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

6. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.8.

New Feature/Enhancement:

1. Add the feature that the system logs can be exported.

2. Change the priority that non-administrator role cannot change the history data retention settings.

3. Optimize the UI of Statistics in Omada Controller.

Bug Fixed:

1. Fix the bug that the External Web Portal cannot authenticate successfully if the SSID of this portal has special characters.

2. Fix the bug that the Cloud Access cannot be displayed normally in the low version of Firefox.

Notes:

1. To use new features on Omada Controller 3.2.x, you need to upgrade your EAP's firmware to the corresponding version.

2. The Omada Controller program needs to use the system's netstat command. If the Linux system does not have net-tools installed (which contain the netstat command), the program may not be able to run normally.

3. Support 64-bit Linux operating system including Ubuntu 14.04/16.04/17.04/18.04, CentOS 6.x/7.x and Fedora 20 or above, Debian 9.8.

4. Built-in JRE 1.8 Java environment.

5. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

6. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.8.

7. When upgrading from Controller 2.5.3 Linux to this version via install.sh, you need to uninstall old version of Controller first.

New Feature/Enhancement:

1. Expand the number of Omada Controller’s User Account to 500.  

2. Optimize the External Portal Server to support URL with parameters.

Notes:

1. To use Omada Controller 3.2.X new features, you need to upgrade your EAP's firmware to the corresponding version.

2. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

3. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.X or earlier version.

New Feature/Enhancement:

1. Expand the number of Omada Controller’s User Account to 500.  

2. Optimize the External Portal Server to support URL with parameters.

Notes:

1. To use Omada Controller 3.2.X new features, you need to upgrade your EAP's firmware to the corresponding version.

2. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

3. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.X or earlier version.

New Feature/Enhancement:

1. Change the mechanism that when adopting an EAP, the Controller will retain the IP configuration of EAP in Standalone mode.

2. Change the mechanism that multiple Omada Controllers can run on the same subnet.

3. Add the button of “Start Omada Controller after installation” and check it by default.

4. Extend the Max Associated Clients in Load Balance to 255.

5. Optimize the UI of Channel Utilization.

6. Optimize the authentication page of portal.

7. Optimize the UI of the portal that you cannot click Apply when you are uploading a photo.

8. Optimize the External Portal Server to support URL with parameters.

Bug Fixed:

1. Fixed the bug that the page of MAC filter may not display all groups when there are more than 5 groups.

2. Fixed the bug that after deleting a site, the Voucher code and Local user of this site still exist.

3. Fixed the bug that the site configuration will fail to restore when the imported site contains same Voucher code as the current Controller.

4. Fixed the bug that when mesh AP is powered off during upgrade, Controller may fail to upgrade other APs, with a prompt message “Other APs are upgrading”.

Notes:

1. To use new features on Omada Controller 3.2.x, you need to upgrade your EAP's firmware to the corresponding version.

2. The Omada Controller program needs to use the system's netstat command. If the Linux system does not have net-tools installed (which contain the netstat command), the program may not be able to run normally.

3. Support 64-bit Linux operating system including Ubuntu 14.04/16.04/17.04/18.04, CentOS 6.x/7.x and Fedora 20 or above, Debian 9.8.

4. Built-in JRE 1.8 Java environment.

5. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

6. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.8.

7. When upgrading from Controller 2.5.3 Linux to this version via install.sh, you need to uninstall old version of Controller first.

New Feature/Enhancement:

1. Change the mechanism that when adopting an EAP, the Controller will retain the IP configuration of EAP in Standalone mode.

2. Change the mechanism that multiple Omada Controllers can run on the same subnet.

3. Add the button of “Start Omada Controller after installation” and check it by default.

4. Extend the Max Associated Clients in Load Balance to 255.

5. Optimize the UI of Channel Utilization.

6. Optimize the authentication page of portal.

7. Optimize the UI of the portal that you cannot click Apply when you are uploading a photo.

8. Optimize the External Portal Server to support URL with parameters.

Bug Fixed:

1. Fixed the bug that the page of MAC filter may not display all groups when there are more than 5 groups.

2. Fixed the bug that after deleting a site, the Voucher code and Local user of this site still exist.

3. Fixed the bug that the site configuration will fail to restore when the imported site contains same Voucher code as the current Controller.

4. Fixed the bug that when mesh AP is powered off during upgrade, Controller may fail to upgrade other APs, with a prompt message “Other APs are upgrading”.

Notes:

1. To use new features on Omada Controller 3.2.X, you need to upgrade your EAP's firmware to the corresponding version.

2. The Omada Controller program needs to use the system's netstat command. If the Linux system does not have net-tools installed (which contain the netstat command), the program may not be able to run normally.

3. Support 64-bit Linux operating system including Ubuntu 14.04/16.04/17.04/18.04/Debian 9.8

4. Built-in JRE 1.8 Java environment.

5. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

6. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.8.

New Feature/Enhancement:

1. Change the mechanism that when adopting an EAP, the Controller will retain the IP configuration of EAP in Standalone mode.

2. Change the mechanism that multiple Omada Controllers can run on the same subnet.

3. Add the button of “Start Omada Controller after installation” and check it by default.

4. Extend the Max Associated Clients in Load Balance to 255.

5. Optimize the UI of Channel Utilization.

6. Optimize the authentication page of portal.

7. Optimize the UI of the portal that you cannot click Apply when you are uploading a photo.

Bug Fixed:

1. Fixed the bug that the page of MAC filter may not display all groups when there are more than 5 groups.

2. Fixed the bug that after deleting a site, the Voucher code and Local user of this site still exist.

3. Fixed the bug that the site configuration will fail to restore when the imported site contains same Voucher code as the current Controller.

4. Fixed the bug that when mesh AP is powered off during upgrade, Controller may fail to upgrade other APs, with a prompt message “Other APs are upgrading”.

Notes:

1. To use Omada Controller 3.2.X new features, you need to upgrade your EAP's firmware to the corresponding version.

2. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

3. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.X or earlier version.

New Feature/Enhancement:

1. Change the mechanism that when adopting an EAP, the Controller will retain the IP configuration of EAP in Standalone mode.

2. Change the mechanism that multiple Omada Controllers can run on the same subnet.

3. Add the button of “Start Omada Controller after installation” and check it by default.

4. Extend the Max Associated Clients in Load Balance to 255.

5. Optimize the UI of Channel Utilization.

6. Optimize the authentication page of portal.

7. Optimize the UI of the portal that you cannot click Apply when you are uploading a photo.

Bug Fixed:

1. Fixed the bug that the page of MAC filter may not display all groups when there are more than 5 groups.

2. Fixed the bug that after deleting a site, the Voucher code and Local user of this site still exist.

3. Fixed the bug that the site configuration will fail to restore when the imported site contains same Voucher code as the current Controller.

4. Fixed the bug that when mesh AP is powered off during upgrade, Controller may fail to upgrade other APs, with a prompt message “Other APs are upgrading”.

Notes:

1. To use Omada Controller 3.2.X new features, you need to upgrade your EAP's firmware to the corresponding version.

2. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

3. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.X or earlier version.

New Feature/Enhancement:

1. Add “Select Page” feature on voucher management page.

2. Change default status of “Terms of Service” on default portal page to uncheck.

3. Optimize the “Free Authentication Policy” to support URL with suffixes.

4. Change the default status of new added “Free Authentication Policy” to enable.

Bug Fixed:

1. Fixed the bug that when clients disconnect from the Facebook portal, the connection time and traffic usage of these clients may be zero in the log.

2. Fixed the bug that AP may disconnect from Omada Controller when it is upgrading the firmware.

3. Fixed the bug that in some cases, the channel configuration of 2.4G frequency may show up in 5G by mistake.

4. Fixed the bug that the configuration of SSID will not be issued correctly when changing the WLAN Group on the provisioning status.

Notes:

1. To use new features on Omada Controller 3.2.X, you need to upgrade your EAP's firmware to the corresponding version.

2. The Omada Controller program needs to use the system's netstat command. If the Linux system does not have net-tools installed (which contain the netstat command), the program may not be able to run normally.

3. Support 64-bit Linux operating system including Ubuntu 14.04/16.04/17.04/18.04/Debian 9.8

4. Built-in JRE 1.8 Java environment.

5. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

6. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.8.

New Feature/Enhancement:

1. Add “Select Page” feature on the management page of vouchers.

2. Change the default status of “Terms of Service” to uncheck.

3. Optimize the “Free Authentication Policy” to support URL with suffixes.

4. Change the default status of new added “Free Authentication Policy” to enable.

Bug Fixed:

1. Fixed the bug that when clients disconnect from the Facebook portal, the connection time and traffic usage of these clients may be zero in the log.

2. Fixed the bug that AP may disconnect from Omada Controller when it is upgrading the firmware.

3. Fixed the bug that in some cases, the channel configuration of 2.4G frequency may show up in 5G by mistake.

4. Fixed the bug that the configuration of SSID will not be issued correctly when changing the WLAN Group on the provisioning status.

Notes:

1. To use new features on Omada Controller 3.2.x, you need to upgrade your EAP's firmware to the corresponding version.

2. The Omada Controller program needs to use the system's netstat command. If the Linux system does not have net-tools installed (which contain the netstat command), the program may not be able to run normally.

3. Support 64-bit Linux operating system including Ubuntu 14.04/16.04/17.04/18.04, CentOS 6.x/7.x and Fedora 20 or above, Debian 9.8.

4. Built-in JRE 1.8 Java environment.

5. Once upgraded to this version of Omada Controller, you will NOT able to downgrade to an earlier version.

6. Portal configuration will be lost after upgraded to Omada Controller 3.2.X from 2.4.8.

7. When upgrading from Controller 2.5.3 Linux to this version via install.sh, you need to uninstall old version of Controller first.

New Feature/Enhancement:

1. Add “Select Page” feature on the voucher management page.

2. Change the default status of “Terms of Service” on default portal page to uncheck.

3. Optimize the “Free Authentication Policy” to support URL with suffixes.

4. Change the default status of new added “Free Authentication Policy” to enable.

Bug Fixed:

1. Fixed the bug that when clients disconnect from the Facebook portal, the connection time and traffic usage of these clients may be zero in the log.

2. Fixed the bug that AP may disconnect from Omada Controller when it is upgrading the firmware.

3. Fixed the bug that in some cases, the channel configuration of 2.4G frequency may show up in 5G by mistake.

4. Fixed the bug that the configuration of SSID will not be issued correctly when changing the WLAN Group on the provisioning status.

Notes:

1. To use Omada Controller 3.2.x new features, you need to upgrade your EAP's firmware to the corresponding version.

2. Once upgraded to this version of Omada Controller, you will NOT be able to downgrade to an earlier version.

3. Portal configuration will be lost after upgrading to Omada Controller 3.2.X from 2.4.X or earlier version.

4. You are recommended to create a backup before upgrading, or you will not be permitted to install this version of Omada Controller.

New Feature/Enhancement:

1. Add “Select Page” feature on the voucher management page.

2. Change the default status of “Terms of Service” on default portal page to uncheck.

3. Optimize the “Free Authentication Policy” to support URL with suffixes.

4. Change the default status of new added “Free Authentication Policy” to enable.

Bug Fixed:

1. Fixed the bug that when clients disconnect from the Facebook portal, the connection time and traffic usage of these clients may be zero in the log.

2. Fixed the bug that AP may disconnect from Omada Controller when it is upgrading the firmware.

3. Fixed the bug that in some cases, the channel configuration of 2.4G frequency may show up in 5G by mistake.

4. Fixed the bug that the configuration of SSID will not be issued correctly when changing the WLAN Group on the provisioning status.

Notes:

1. To use Omada Controller 3.2.x new features, you need to upgrade your EAP's firmware to the corresponding version.

2. Once upgraded to this version of Omada Controller, you will NOT be able to downgrade to an earlier version.

3. Portal configuration will be lost after upgrading to Omada Controller 3.2.X from 2.4.X or earlier version.

4. You are recommended to create a backup before upgrading, or you will not be permitted to install this version of Omada Controller.

New Feature/Enhancement:

1. Support to discover the gateway and switch that support Omada SDN platform.

2. Add timeout mechanism during adopting the devices.

Note:

1. This version of software can be used in both Windows and Mac operation system.

2. Double click the software or run the command “java –jar **.jar” to run the software on MacOS (**.jar is the name of this software).

3. To run this software, you need to install JRE 8.0 on your PC first.

4. Omada Controller and Discover Utility cannot run on the same computer at the same time.

New Feature/Enhancement:

1. Fully adapted to Omada SDN Controller v4.1.4.

2. Support to discover the gateway and switch that support Omada SDN platform.

Note:

1. This version of software can be used in both Windows and Mac operation system.

2. Double click the software or run the command “java –jar **.jar” to run the software on MacOS (**.jar is the name of this software).

3. To run this software, you need to install JRE 8.0 on your PC first.

4. Omada Controller and Discover Utility cannot run on the same computer at the same time.